3D Systems Cubify CUBEX Duo Bedienungsanleitung

CUBEX

Measuring

Stepper motor

chip voltages

Contents

What you will need ..................................................................................................... 3

Removing the Jet Wipe .............................................................................................. 4

Removing the Case and floor panel. .......................................................................... 4

Voltage Measurement Locations................................................................................ 6

Reading the Voltages................................................................................................. 7

Re attaching the floor panel and case........................................................................ 8

What you will need

Multimeter

3mm hex driver

Small Screwdriver

Before beginning this process please ensure that all cartridges have been

removed from the machine.

Removing the Jet Wipe

Run the bed to the bottom of the machine using manual move.

Lift Jet wipe out of the machine

Removing the Case and floor panel.

Using the 3mm hex driver remove the 8 case bolts (4 either side of the machine).

Unplug the CubeX screen.

Lift the case up off the CubeX.

Using the 3mm hex driver undo the 5 bolts holding the floor panel to the machine.

Lift the front of the floor panel and cable tie it to the bed arms. This will allow you

access to the Main Board PCB.

Voltage Measurement Locations

Depending which stepper motor chip voltage you want to read, you will need to

position your multimeter in different positions of the board. You will need to place a

small screwdriver with one end of the multimeter clipped onto it on the small screw

head labelled TP – and another end of the multimeter will need to be set to ground

on the board.

TP X will measure the voltage for the X axis.

TP Y will measure the voltage for the Y axis.

TP Z will measure the voltage for the Z axis.

TP E1, TP E2 and TP E3 will measure the voltage for print jets 1, 2 and 3.

TP Z

TP Y

TP X

Ground

Reading the Voltages

Plug the CubeX into mains power

Set the multimeter to read DC voltage.

Place the Red (positive) lead onto the desired TP screwhead.

TP E1

TP E2

TP E3

Hold the other end of the multimeter against the ground point.

The multimeter screen will give you your voltage reading.

TP X should read 1.3VDC

TP Y should read 1.6VDC

TP Z should read 1.3VDC

TP E1, E2 and E3 should read 1.1VDC

If your voltage is not correct use the small screwdriver to turn the screwhead in very

small increments measuring the voltage between each turn until it is correct.

Unplug your CubeX from mains power.

Re attaching the floor panel and case.

Cut the cable tie holding the floor panel in place and gently lower it down.

Using the 3mm hex driver re attach the 5 bolts that hold the floor panel.

Slide the case onto the CubeX and plug in the CubeX screen.

Using the 3mm Driver re attach the 8 case bolts.

You may now power up your CubeX.

Andere Handbücher für Cubify CUBEX Duo

Inhaltsverzeichnis

Andere 3D Systems 3D-Drucker Handbücher

3D Systems

3D Systems CubePro 3D Printer Bedienungsanleitung

3D Systems

3D Systems CubePro Bedienungsanleitung

3D Systems

3D Systems ProJet 6000 Bedienungsanleitung

3D Systems

3D Systems BFB-3000 Bedienungsanleitung

3D Systems

3D Systems CubePro Bedienungsanleitung

3D Systems

3D Systems CubePro Bedienungsanleitung

3D Systems

3D Systems Cubify CUBEX Duo Bedienungs- und Sicherheitshinweise

3D Systems

3D Systems CubePro Bedienungsanleitung

3D Systems

3D Systems ProX 800 Bedienungsanleitung

3D Systems

3D Systems ProJet MJP 5600 Bedienungsanleitung

3D Systems

3D Systems ProX DMP 100 Bedienungsanleitung

3D Systems

3D Systems CubePro Bedienungsanleitung

3D Systems

3D Systems SLA 750 Series Bedienungsanleitung

3D Systems

3D Systems ProX 500 Bedienungsanleitung

3D Systems

3D Systems ProJet 5500X Bedienungsanleitung

3D Systems

3D Systems DuraForm TPU Elastomer Bedienungsanleitung

3D Systems

3D Systems ProJet MJP 3600 Bedienungsanleitung

3D Systems

3D Systems ProJet 1200 Bedienungsanleitung

3D Systems

3D Systems iPro 8000 SLA Center Bedienungsanleitung

3D Systems

3D Systems ProX DMP320 Bedienungsanleitung

3D Systems

3D Systems CUBE Bedienungsanleitung

3D Systems

3D Systems ProX 950 Bedienungsanleitung

3D Systems

3D Systems Cube 3rd Generation Bedienungsanleitung

3D Systems

3D Systems ProJet 1200 Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch