3M 4084 Bedienungsanleitung

February 2002

78-8122-2476-0-A

4084/4086 Expansion Kit

Instructions

2.0 Description

2.1 Kit Parts

-Side Rail Assemblies (2)

-Door Assemblies (4)

-Frame Supports, upper and lower

-Replacement Gasket and Weather-strip.

-4015C Cap Replacement Kit

-300 pair Frame (3)

-600 pair Frame (3)

-Labels and Hardware

2.2 Tools needed for Installation:

-Drill or hammer and chisel

-1/4” ratchet with 7/16” and 9/16 sockets

3.0 Prepare Existing Cabinets for

Expansion

3.1 Remove the cap bolts and the cap by pushing it up.

3.2 Remove the doors.

a. Cabinet with door Piano Hinges.

1. Loosen door bolts.

2. Lift doors up and off, remove the bolts.

b. Cabinet with door hinge posts.

1. Lift doors up and off.

2. Use a drill or hammer and chisel to remove

all cabinet hinges from side rails.

3.3 Remove jumper wire spools, plastic trays and

discard spool holder brackets.

3.4. Knock out the press nut inserts from the top of

the side rails.

1.0 General

1.1 The 4084/4086 Expansion Kit increases the cross connect capacity of an existing 4084 or 4086 Cabinet to

3600 pairs. There is no service interruption during installation and the new and existing feeder and

distribution pairs can be jumpered to each other.

Narrow 4084

Narrow 4086

Wide 4084

Wide 4086

4086 Expansion

Side Rail

Existing Cabinet Side Rails

Hole for carriage bolt

on old style side rail

#10 carr bolt

3.5 Installing the Expansion Side Rail

a. Figure 1 shows the four versions of the

existing cabinet Side Rails and the

Expansion Kit Side Rail:

4.0 Install the 4084/4086 Expansion Kit

See Figure 2 for placement of new Kit parts

to the cabinet.

4.1 Place the Expansion Rails on the top edge of

the cabinet base, align the attachment holes to

the side rails. Secure the expansion rails to

the side rails with carriage bolt heads out.

4.2 Install the new jumper runs on the lower

support.

4.3 Remove the bolts holding the existing upper

support to old side rails and install the new

lower support

4.4 Install the upper support.

4.5 Install either a 300 or 600 pair Frame as

required, secure between upper and lower

supports.

4.6 Mount the new cap with the cup washer bolts.

4.7 Install the jumper spool trays over the nylon

buttons on upper support.

4.8 Remove the old weather-stripping from skirt,

wipe the surfaces clean and install new

weather-stripping.

4.9 Install the new doors and latch assemblies.

4.10 Install two new 4247 Tool and Probe

Assemblies, front and rear.

4.11 Check and tighten all existing cabinet

hardware.

Cap

Wire Spool & Tray

Upper Support

300 pr. or 600 pr.

Frame Assembly (3)

Extended Side Rails

Jumper Runs (2)

Lower Support

Existing Upper Support

Figure 1

Figure 2

Important Notice

Before using this product, you must evaluate it and determine if it is suitable for your intended application.You assume all risks and liability

associated with such use.

Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture as of the date of purchase.

3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FIT-

NESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be,

at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will

not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential

regardless of the legal theory asserted.

Telecommunications

6801 River Place Blvd.

Austin, TX 78726-9000

800/426-8688

FAX 800/626-0329

www.3M.com/telecom Litho in USA

40% Pre-consumer waste paper

10% Post-consumer waste paper

5.0 Cable Routing in the Expansion Cabinet

5.1 After the cabinet has the Expansion Kit installed route the new cables to the expansion frames according

to Figure 3.

Cable Routing

Figure 3

Dieses Handbuch passt für folgende Modelle

Andere 3M Industrieanlagen Handbücher

3M 3M-Matic S-857 Datenblatt

3M Attest 390 Bedienungsanleitung

3M 3M-Matic 120af3 Datenblatt

3M AccuGlide HST Upper Datenblatt

3M Flexiguard 8517762 Bedienerhandbuch

3M Flexiguard 8560025 Bedienerhandbuch

3M DBI SALA 2100090 Bedienungsanleitung

3M 39600 Datenblatt

3M SelfCheck System 6210 Bedienungsanleitung

3M Detection System 3500 Series Bedienungsanleitung

3M 3M-Matic Accuglide NPH 11200 Datenblatt

3M Liqui-Cel EXF-10x28 Series Montageanleitung

3M 4990 Bedienungsanleitung

3M 8350 D Montageanleitung

3M QT-III Bedienungsanleitung

3M Crimplok 8702-UPC Bedienungsanleitung

3M Liqui-Cel EXF-14 28 Series Montageanleitung

3M Attest Auto-reader 490 Bedienungsanleitung

3M FDC 08M Bedienungsanleitung

3M 3M-Matic Accuglide 21700 Datenblatt

3M 4220CUE-6000 Bedienungsanleitung

3M MEMBRANA Liqui-Cel Bedienungsanleitung

3M Scotchlok Tap Connector 558 Bedienungsanleitung

3M 50AN Technisches Datenblatt

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung