3M PPS Series 2.0 Bedienungsanleitung

Andere Handbücher für PPS Series 2.0

3

Andere 3M Spritzpistole Handbücher

3M

3M Performance Spray Gun Bedienungsanleitung

3M

3M Accuspray Bedienungsanleitung

3M

3M PPS Series 2.0 Bedienungsanleitung

3M

3M PPS HVLP Bedienungsanleitung

3M

3M Series 05 Bedienungsanleitung

3M

3M Accuspray Bedienungsanleitung

3M

3M Accuspray HGP Spray Gun Bedienungsanleitung

3M

3M Accuspray 16580 Bedienungsanleitung

3M

3M 10 Bedienungsanleitung

3M

3M 16212 Bedienungsanleitung

3M

3M Accuspray 26580 Bedienungsanleitung

3M

3M PPS Series 2.0 Bedienungsanleitung

3M

3M Performance Spray Gun Bedienungsanleitung

3M

3M PPS Series 2.0 Bedienungsanleitung

3M

3M Series 52 Bedienungsanleitung

3M

3M Accuspray Bedienungsanleitung

3M

3M Scotchkote HSS-450 Bedienungsanleitung

3M

3M PPS 16121 Bedienungsanleitung

3M

3M 97-044 Bedienungsanleitung

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

Graco

Graco EM 390 Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung

Graco

Graco HydroShield WMBH00 Stücklistenhandbuch

WAGNER

WAGNER W 125 Bedienungsanleitung

Assembly

1Attach the supplied air flow valve to the bottom of the gun.

2Attach the nozzle to the spray gun with the locking collar fully connected. Note: It

is easier to install the nozzle while pulling the trigger backward toward the spray

gun handle. To remove the nozzle from the spray gun, reverse the process.

3Attach 3M™PPS™Series 2.0 spray cup to nozzle. See back for directions.

4Once the spray gun is properly assembled you may attach the air line.

For additional questions, contact your local 3M representative

or email: aaduk[email protected].

See manual for additional use and health and safety information.

Recommended set up starting points

Fan control knob: Open 1.5 turns for HVLP nozzles, 2.5 turns for Fine Finish

nozzles from closed position

Fluid control knob: Open 4 rotations from closed position

See recommended pressure setting on Atomising Head Air Cap.

Nozzle recommendation

* Starting points only, refer to Paint Manufacture for recommendation

onfluid tip size.

2.0 1.8 1.6 1.4 1.3 1.2 0.9

High viscosity coatings • •

Sprayable fillers • •

High build primer • • •

Primer surfacer • • •

Wet on wet primer • •

Primer sealer • •

Direct gloss •

Single stage top coat •

Solvent base colour • •

Clearcoat • • •

Waterborne base coat • •

UV Primers • • •

Midcoat / Effect Coats • • •

Smart / Spot repair •

WARNING! Do not immerse spray gun or nozzles in cleaning solvents or gun washers.

*Operating Pressure Range (OPR) is the inlet pressure range for safe function of the spray gun.

3M™Performance Spray Gun – Gravity

Operating Pressure Range* is between 7 psi - 37 psi (0.5 bar - 2.6 bar)

Adding the 3M™PPS™Series 2.0 SprayCup

SystemComponents

1Insert the 3M™PPS™Series 2.0 Spray Cup System

disposable liner into the 3M™PPS™Series 2.0 Spray

Cup System mixing cup.

2Pour material to be sprayed into the 3M™PPS™

Series 2.0 Spray Cup System mixing cup. Stir

asneeded.

3Place the 3M™PPS™Series 2.0 Spray Cup System

lid with built-in filter on top of the 3M™PPS™mixing

cup with liner and snap into place.

4Turn until tight. Insert 3M™PPS™Series 2.0 Spray

Cup System sealing plug prior to shaking or sealing.

5Attach spray gun to filled 3M™PPS™Series 2.0

Spray Cup System cup.

Cleaning

1Once coating application is complete, disconnect the air hose

fromthegun.

2To drain back paint into cup – invert cup, pull trigger, and tap

the3M™PPS™Series 2.0 cup on a table 3 times.

3Rinse out nozzle spout and flush cleaning solvent through the nozzle

by pulling trigger with fluid tip pointed straight down into receptacle

tocollect waste solvent.

4Store spray gun with a clean nozzle attached to protect the needle.

3M™Performance Spray Gun – Gravity

Operating Pressure Range* is between 7 psi - 37 psi (0.5 bar - 2.6 bar)

ATTENTION

Note: Do not put Spray Gun/Spray Gun Body in Gun Washer.

© 3M 2022. 3M and PPS are trademarks of 3M Company. All rights reserved.

For additional questions, contact your local 3M representative

or email: [email protected].

See manual for additional use and health and safety information.