3M X56 Handbuch
1
WARNING ►Before using this product, be sure to read all manuals for this
product. After reading them, store them in a safe place for future reference.
►Follow all the instructions in the manuals or on the product. The manufacturer
assumes no responsibility for any damage caused by mishandling that is beyond
normal usage dened in the manuals.
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
Trademark acknowledgment
All the trademarks in this manual are the properties of their respective owners.
Features
This projector can be used with another projector of the same type to project an
image on the same screen using the Instant Stack feature.
The two projectors can be operated simultaneously to make the image brighter.
Moreover, if you connect two projectors with RS-232C cross-over cable, it turns to
a kind of intellectual stacking system. The two projectors can work alternately by
themselves, and once one projector has an accident the other voluntarily starts to
work to keep your presentation going.
These features, generically called Instant Stack, provide you with the broad use.
Digital Projector X56
Operator's Guide
Instant Stack Guide
Thank you for purchasing this product.
This manual is intended to explain only Instant Stack feature. Other than what is
mentioned in this manual, please see other manuals of this product.
2
3M™ Digital Projector X56
© 3M 2011. All Rights Reserved.
1. Introduction ........................3
1.1 Entries and graphical
symbols explanation ........................ 3
1.2 Important safety instruction .......... 3
Instant Stack feature ............................ 3
General installation .............................. 5
1.3 Basic information
and preparations ............................. 6
Instant Stack ........................................ 6
Intellectual Stack and Simple Stack ..... 6
Remote control for Intellectual Stack
and Simple Stack ............................. 6
Installation styles ................................. 6
Tentative terms for the two projectors .. 6
2. Installation ..........................7
2.1 Preparing for Intellectual Stack..... 7
2.2 Installing
the rst projector (Set A) ................ 8
Removing pocket caps ........................ 8
Preparing elevator feet ........................ 8
Deciding installation position ............... 8
Setting up Set A ................................... 9
2.3 Installing
the second projector (Set B) ........ 11
Stacking the projectors ...................... 11
Connecting projectors ........................ 11
Setting up Set B ................................. 12
2.4 Conrming Main
and Sub settings ............................ 14
2.5 Fine adjusting
image position ............................... 15
For Intellectual Stack users ............... 15
For Simple Stack users ...................... 16
3. STACK menu settings ......17
3.1 Displaying STACK menu ............ 17
3.2 Selecting Main, Sub or off .......... 18
3.3 Selecting lamp operation mode .. 19
3.4 Selecting lamp switching mode .. 21
3.5 Selecting input source for Sub.... 22
3.6 Exiting Intellectual
Stack menu ................................... 23
STACK menu ..................................... 23
Dialog from STACK menu .................. 23
3.7 Important information
for Intellectual Stack ...................... 24
4. Connecting cables ...........27
4.1 Connecting an RS-232C cable ... 27
4.2 Connecting signal cables............ 28
Inputting image from Main to Sub ...... 28
Inputting image
to Sub and Main individually ........... 28
5. Setting input ports
using menu.........................29
5.1 Preparing for menu operations ... 29
5.2 Checking Main projector's
operating status ............................. 29
5.3 Starting up Main projector .......... 30
5.4 Setting the menu ........................ 31
Inputting image from Main to Sub
- Computer signal ........................... 31
Inputting image from Main to Sub
- Video signal
(either component or video) ........... 32
Inputting image to
Sub and Main individually ............... 32
6. Restrictions
on Schedule function ........34
7. Troubleshooting ...............36
Contents
3
3M™ Digital Projector X56
© 3M 2011. All Rights Reserved.
1.1 Entries and graphical symbols explanation
The following entries and graphical symbols are used for the manuals and the
product as follows, for safety purpose. Please know their meanings beforehand,
and heed them.
1.2 Important safety instruction
The followings are important instructions for safely using the product in Instant
Stack. First of all, read the following instructions and be sure to always follow
them when using Instant Stack of this product.
(continued on next page)
WARNING This entry warns of a risk of serious personal injury or even
death.
CAUTION This entry warns of a risk of personal injury or physical
damage.
NOTICE This entry notices of fear of causing trouble.
WARNING ► Take a special care not to fall the stacked projectors.
• When stacking two projectors, make sure the elevator feet and heel of the
upper projector are inserted into the corresponding pockets of the lower
projectors. (
11
)
• When using the Instant Stack function by piling up two projectors, you can
change the projection angle by adjusting the
elevator feet of the unit that is placed underneath.
(
8
) Exercise care to prevent the stacked projector
from falling off or tipping over while adjusting the
elevator feet.
• A maximum of two projectors can be stacked. Do
not stack three or more projectors.
• Do not install the projectors that are stacked using
the stack pockets, elevator feet and heel of this
projector at a place higher than a person's height.
• Do not install the projectors that are stacked using
the stack pockets, elevator feet and heel of this
projector on a ceiling.
• Do not touch the stacked projectors except when
instructions are given in this manual. Do not hit the
projectors with any type of object.
Pocket cap
Stack pocket
LOCK
Elevator feet
Heel
Cap storage
pocket
Lens
adjuster
door
Stack
pocket
1. Introduction
Instant Stack feature
4
Introduction
3M™ Digital Projector X56
© 3M 2011. All Rights Reserved.
1.2 Important safety instruction - For Instant Stack feature (continued)
NOTICE ► Instant Stack is a feature that allows you to stack two projectors
or arrange them side by side easily. Depending on the installation and
surrounding environment, images projected from the two projectors may not
superimpose well enough. The images cannot superimpose well enough
especially when the screen is slanted, deformed or the surface is uneven.
• Images projected immediately after turning on the projectors are unstable due
to rising internal temperature. Wait for more than 20 minutes before starting
to adjust the superimposed images.
• The image positions may shift due to temperature change, vibration, or shock
caused by hitting the projector. Install the projectors in a stable environment
when using Instant Stack. If the image positions are shifted, readjust the
images. (
9, 12, 15
)
• The image positions may shift over time due to the tension and the weight of
the connecting cables. Make sure not to impose any load on the projectors
when arranging the cables.
• If the volume level of the built-in speakers is too high, the two projectors may
resonate, noise may occur and the image quality may deteriorate. In this
case, check the volume setting on both projectors. Lower the volume until the
symptoms disappear or arrange the projectors side by side.
• When two projectors are connected using the RS-232C cable, the Main
projector will be able to control the Sub projector. This feature is known as
Intellectual Stack. (
11
) When Intellectual Stack by means of RS-232C
feature is used, RS-232C communication cannot be used to control the
projector. If you wish to control the projectors, use the LAN connection that is
connected to any of the projectors.
• When Intellectual Stack is used, the operations or settings of some functions
are restricted. Refer to this manual for details. (
34
)
WARNING ► When removing the pocket caps from the stack pockets, be
sure to store them securely and safely inside the lens adjuster door to prevent
children and pets from swallowing the caps. (
3
) If swallowed, consult a
physician immediately.
CAUTION ► Be careful not to injure your nail and nger when removing
the pocket caps. (
3
)
5
Introduction
3M™ Digital Projector X56
© 3M 2011. All Rights Reserved.
General installation
NOTICE ► Position the projector to prevent light from directly hitting the
projector’s remote sensor.
• Do not place the product in a place where radio interference may be caused.
CAUTION ► Place the projector in a cool place with sufcient ventilation.
• Keep a space of 30 cm or more between a side of the projector and other
objects such as a wall. If you install two projectors in Style 2 (
6
), keep a
space of 30 cm or more between the two projectors.
• Do not stop up, block nor cover the projector’s vent holes.
• Do not place the projector at places that are exposed to magnetic elds, doing
so can cause the cooling fans inside the projector to malfunction.
► Avoid placing the projector in smoky, humid or dusty place.
• Do not place the projector near humidiers. Especially for an ultrasonic
humidier, chlorine and minerals contained in tap water are atomized and
could be deposited in the projector causing image degradation or other
problems.
WARNING ► Install the projector where you can access the power outlet
easily.
► Do not subject the projector to unstable conditions. Install the projector in a
stable horizontal position.
• Do not use any mounting accessories except the accessories specied by the
manufacturer. Read and keep the manuals of the accessories used.
• For special installation such as ceiling mounting, be sure to consult your
dealer beforehand. Specic mounting accessories and services may be
required.
► Do not install the projector near thermally conductive or ammable things.
► Do not place the projector where any oils, such as cooking or machine oil,
are used.
► Do not place the projector in a place where it may get wet.
6
Introduction
3M™ Digital Projector X56
© 3M 2011. All Rights Reserved.
Tentative terms for the two projectors
For better understanding of the descriptions in this
manual, the following terms are used when explain-
ing the vertical stacking installation.
Set A : Projector placed underneath
Set B : Projector placed on top of Set ASet A
Set B
Installation styles
Following are two styles to install the projectors. Instant Stack supports both
styles.
Style 1 : Stack vertically
Style 2 : Arrange side by side
The descriptions in this manual are mainly on Style 1 installation. If you wish to
install two projectors in Style 2, refer to the descriptions required in this manual.
1.3 Basic information and preparations
Instant Stack
Instant Stack is a feature that allows you to superimpose images projected from
two projectors easily. This projector is designed to provide this feature, with func-
tions to install two projectors and superimpose the images.
Intellectual Stack and Simple Stack
Instant Stack includes the following two features.
When two projectors are connected via an RS-232C cable with necessary set-
tings performed on the projectors, these two projectors will automatically operate
in synchronization with each other according to the settings. This is known as
Intellectual Stack in this manual.
The two projectors operate individually without the RS-232C connection. This is
known as Simple Stack in this manual.
Remote control for Intellectual Stack and Simple Stack
For Intellectual Stack, one projector is set as Main and the other is set as Sub.
(
18
) Only the Main projector is capable of receiving the remote control signals.
To operate the Sub projector, you need to point the remote control at the Main
projector.
For Simple Stack, both projectors can receive the remote control signals. To
avoid crosstalk when operating with the remote control, it is recommended to
operate one projector with the remote control and the other with the control panel
on the projector or a wired remote control. In this case, disable the remote control
receiving on the other projector with the KEY LOCK feature. (Operator's Guide
→ OPTION menu)
7
3M™ Digital Projector X56
© 3M 2011. All Rights Reserved.
For safety reasons, read 1.2 Important safety instruction (
3~5
) carefully before
installation. In addition, take note of the followings for proper use of Instant Stack.
● When using Intellectual Stack, both projectors will respond to the remote control
signals until STACK MODE on either projector is set to SUB.
During installation, it is recommended to operate one projector with the remote
control and the other with the control panel on the projector or a wired remote
control. In this case, disable the remote control receiving on the other projector
with the KEY LOCK feature. (Operator's Guide → OPTION menu)
●Images from Set A and Set B may superimpose well but the image positions
can shift over time.
Readjust to superimpose the images.
●If the volume level of the built-in speakers is too high, the two projectors may
resonate, noise may occur and the image quality may deteriorate.
In this case, check the volume setting on both projectors. Lower the volume
until the symptoms disappear or arrange the projectors side by side. If the
image positions are shifted, readjust.
2.1 Preparing for Intellectual Stack
When using Intellectual Stack via RS-232C connection, ensure the following set-
tings are set on the two projectors. Otherwise, the Intellectual Stack menu cannot
be operated.
●STANDBY MODE in SETUP menu: NORMAL
(Operator's Guide → SETUP menu)
●COMMUNICATION TYPE under COMMUNICATION in SERVICE menu: OFF
(Operator's Guide → OPTION menu)
●STACK LOCK in SECURITY menu: OFF
When STACK LOCK is set to on, menus related to Instant Stack cannot be
operated. It is therefore necessary to set it to off during installation and menu
setting.
(1) Use the ▲/▼/◄/► buttons to go into the following menu.
ADVANCED MENU > SECURITY
> STACK LOCK
STACK LOCK dialog will appear on screen. (Operator's
Guide → SECURITY menu)
(2) Use the ▲/▼ buttons to highlight OFF, and press the ► button to complete
the setting.
2. Installation
8
Installation
3M™ Digital Projector X56
© 3M 2011. All Rights Reserved.
NOTE • Set the tilt angle of Set A to within 12 degrees from the level line.
• Take the followings into account when considering the installation position.
- VERTICAL adjuster should be set to the upper limit position.
- ZOOM ring should not be set to the widest position.
- HORIZONTAL adjuster is recommended to be set near the center position.
Preparing elevator feet
When stacking the two projectors, set the length of the
elevator feet to the minimum using the elevator but-
tons on Set A and B.
CAUTION ► Be careful when stacking the two
projectors, the projector on top may slide down.
NOTE • Cap storage pockets for the pocket caps
are inside the lens adjuster door. Be sure to keep
the caps in the storage pockets after removing the
caps from the stack pockets.
To store the cap to the pocket, place the thin end of
the cap into the pocket rst, then push the other side
of the cap down rmly to the bottom of the pocket.
It is important to ensure that the caps are securely
stored to prevent children and pets from swallowing
them.
Thin end
Cap storage
pocket
Pocket caps
CAUTION ► It is recommended to use a pin or
the like to remove the caps. If you are using nger,
be careful not to injure your nail and nger.
Removing pocket caps
When stacking the two projectors, remove the pocket
caps on Set A.
Deciding installation position
Decide the position of Set A and its projection angle. (Operator’s Guide →
Arrangement and Adjusting the projector’s elevator)
2.2 Installing the rst projector (Set A)
9
Installation
3M™ Digital Projector X56
© 3M 2011. All Rights Reserved.
2. Set the lens position to the upper limit with the VERTICAL adjuster.
NOTE • If it is not set to the upper limit, the image of Set B may not
superimpose well enough to the image of Set A.
• Perform the MIRROR setting rst if necessary as it may change the image
position. (Operator's Guide →SETUP menu)
• HORIZONTAL adjuster is recommended to be set near the center position.
3. Adjust the image of Set A to t the screen with the VERTICAL adjuster,
HORIZONTAL adjuster, ZOOM ring and FOCUS ring. (Operator’s Guide →
Displaying the picture)
Adjust the image position using KEYSTONE and PERFECT FIT if necessary.
(Operator's Guide →EASY MENU or SETUP menu)
NOTE • Do not adjust ZOOM ring to the widest position, otherwise the
image of Set B may not superimpose well enough to the image of Set A. Fine
adjusting the image position of Set B electrically does not increase its image
size. Use the ZOOM ring to adjust the image size of Set B to slightly larger
than Set A.
• KEYSTONE cannot be operated when PERFECT FIT is in use. To adjust
the image using both KEYSTONE and PERFECT FIT, adjust KEYSTONE
rst.
• If you are using Simple Stack, go to 2.3 Installation of the second projector
(Set B). (
11
)
(continued on next page)
Setting up Set A
1. Turn on Set A.
4. Display the menu with the MENU button. (Operator's Guide →Using the
menu function)
5. Use the ▲/▼/◄/► buttons to go into the following menu.
ADVANCED MENU > OPTION
> SERVICE > COMMUNICATION
> STACK
STACK menu will appear on screen.
(Operator's Guide →OPTION menu)
10
Installation
3M™ Digital Projector X56
© 3M 2011. All Rights Reserved.
NOTE • Set A will not be operated by the remote control hereafter. To
avoid crosstalk when operating with the remote control, it is recommended to
disable the remote control receiving using KEY LOCK.
• After the STACK MODE setting is completed, Set A (Sub) will not be able
to receive the remote control signals. When STACK MODE is set to OFF,
enable the remote control receiving using KEY LOCK if necessary.
8. If you are using Intellectual Stack, disable the remote control receiving using
KEY LOCK. (Operator's Guide →OPTION menu)
7. After pressing the ► button, a dialog to
conrm whether or not to save the setting is
displayed.
Press the ► button to complete the setting. (
23
)
2.2 Installing the rst projector (Set A) - Setting up Set A (continued)
6. Use the ▲/▼ buttons to highlight STACK
MODE, and press the ► button to display
the STACK MODE dialog.
Highlight SUB pressing the ▲/▼ buttons,
and press the ► button.
Andere Handbücher für X56
3
Inhaltsverzeichnis
Andere 3M Projektor Handbücher
3M
3M WX20 - Digital Projector WXGA LCD Bedienungsanleitung
3M
3M MP 180 Bedienungsanleitung
3M
3M 1825 Plus Bedienungsanleitung
3M
3M Multimedia Projector X62 Bedienungsanleitung
3M
3M Multimedia Projector MP8780 Handbuch
3M
3M X46i Handbuch
3M
3M Multimedia Projector MP8610 Bedienungsanleitung
3M
3M Multimedia Projector X70 Bedienungsanleitung
3M
3M X21 Handbuch
3M
3M Overhead Projector 1700 Bedienungsanleitung
3M
3M DMS800 - Digital Media System 800 XGA DLP... Installations- und Betriebsanleitung
3M
3M Multimedia Projector MP7760 Handbuch
3M
3M PX5 Series Bedienungsanleitung
3M
3M Multimedia Projector X65 Bedienungsanleitung
3M
3M X95 - Digital Projector XGA LCD Betriebsanleitung
3M
3M X64W - Digital Projector XGA LCD Handbuch
3M
3M Multimedia Projector MP8730 Bedienungsanleitung
3M
3M DX60 Bedienungsanleitung
3M
3M Multimedia Projector S15 Betriebsanleitung
3M
3M Multimedia Projector S10 Bedienungsanleitung
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
