3M 7500 Series Bedienungsanleitung

Andere Handbücher für 7500 Series

2

Inhaltsverzeichnis

Beliebte Atemwegsprodukt Handbücher anderer Marken

Omron

Omron COMP A-I-R NE-C801 Bedienungsanleitung

CERES

CERES nosko nebulizer kit Bedienungsanleitung

Dr.Frei

Dr.Frei NE-SM1 Bedienungsanleitung

North

North 5400 series Bedienungsanleitung

John Bunn

John Bunn Neb-u-Lite LX2 Bedienungsanleitung

DeVilbiss

DeVilbiss UltraNeb Bedienungsanleitung

Sperian

Sperian Panther Hip-Pac P9684 Series Bedienungsanleitung

Dräger

Dräger X-plore 6570 Bedienungsanleitung

Respironics

Respironics SideStream HS860 Bedienungsanleitung

Sundstrom

Sundstrom SR 500 Bedienungsanleitung

JARDIBRIC

JARDIBRIC KPBRU20 Bedienungsanleitung

Ombra

Ombra 63506 Bedienungsanleitung

Lotus

Lotus M-9520A Bedienungsanleitung

Philips

Philips Respironics EE Leak 1 AF541 Bedienungsanleitung

EVOLU

EVOLU Nano AiR MINI Bedienungsanleitung

Ambu

Ambu SPUR II Bedienungsanleitung

MSA AUER

MSA AUER 3S-PF Bedienungsanleitung

MSA

MSA C420 Bedienungsanleitung

Respirators must be inspected before each use to ensure good operating condition.

The facepiece must be repaired or replaced if there are damaged or defective parts.

7500 SERIES RESPIRATOR INSTRUCTIONS

Inspection Procedure

Check facepiece for cracks,

tears and dirt. Be certain

facepiece, especially face-

seal area, is not distorted.

1

Examine inhalation valves

for signs of distortion,

cracking or tearing.

2

Make sure that head straps

are intact and have good

elasticity.

3

Examine all plastic parts

for signs of cracking or

fatiguing. Make sure filter

gaskets and seal areas are

in good condition.

4

Examine exhalation valve

and valve seat for signs of

dirt, distortion, cracking or

tearing.

5

7500 SERIES RESPIRATOR INSTRUCTIONS

Donning Procedure

Proper donning procedures must be followed to ensure the respiratory

protection rating is achieved.

Place halo shaped plastic

strap on back of head.

1

Attach clasp on strap behind

neck.

2

Pull all straps until

mask is firm on face.

3

7500 SERIES RESPIRATOR INSTRUCTIONS

To ensure adequate respiratory protection the facepiece must form a

seal on your face. If you cannot achieve a proper seal do not enter the

contaminated area.

Seal Check Procedure

The 3M 7093 Filter Cartridge

is designed to seal and block

airflow when compressed

together.

1

Using hands squeeze both

filter cartridges between

palm and fingers. Be careful

not to disturb the position of

the respirator.

2

Inhale gently. If you feel the

facepiece collapse slightly and

pull closer to your face with

no leaks between your face

and the facepiece, a proper

seal has been achieved.

3

If face-seal air leakage is

detected, reposition

respirator on face and/or

readjust tension of

straps to eliminate the

leakage.

4

7500 SERIES RESPIRATOR INSTRUCTIONS

Doffing Procedure

Proper doffing procedures must be followed to reduce the risk of

exposure to contaminates on the outside of the mask. Ensure that

your gown has been doffed before doffing your respirator.

Doff contaminated PPE

And

Remove contaminated

gloves.

1

Put a new pair of

clean gloves on.

2

Undo clasp on strap behind

neck.

3

Locate the elastic straps

near your ears and pull

out/up, removing the

mask away from you.

4

Carefully remove and

place in an area ready for

cleaning.

5

7500 SERIES RESPIRATOR INSTRUCTIONS

Cleaning Procedure

Respirators must be thoroughly cleaned after being contaminated and

at the end of each shift. Whena full cleaning is not possibleSani-Hands

wipes may be used to wipe the outside of the mask to perform partial

cleaning. Do not wipe the inside of the maskwith the same wipe used

to wipe the outside.

Use the following supplies

from your station inventory:

•2 Red Buckets (cleaned)

•Waxie 910 solution

•Wipe-all towels

•Nitrile Gloves

1

Fill two buckets with warm

Waxie 910 cleaner using the

mop bucket filler.

not to exceed 120º F

2

Remove filter cartridges. Wipe

plastic with 910 saturated

Wipe-all.

3

DO NOT spray cleaner

inside the cartridge.

DO NOT use compressed

air to clean cartridge.

Clean FACEPIECE ONLY (not

filters) by immersing in first

bucket of warm 910 solution,

rubbing with Wipe-all.

4

Disinfect by submerging in

second bucket of warm 910

solution for 60 seconds.

Allow 910 cleaner to stay on

mask for 9 minutes before

rinsing with water.

5

Rinse in fresh, warm water and

air dry in non-contaminated

atmosphere.

6

When reassembling your mask

ensure that your filter is in

good working order and not

expired.

7

Replace the filter if it is expired, damaged or

producing excess resistance when breathing.