3M Speedglas 9002 Montageanleitung

User Instruction

Bedienungsanleitung

Notice d’instructions

Èíñòðóêöèÿ ïî ýêñïëóàòàöèè

²íñòðóêö³ÿ ç åêñïëóàòàö³¿

Instruzioni d’uso

Gebruiksaanwijzing

Instrucciones de uso

Instruções de uso

Bruksanvisning

Brugsanvisning

Käyttöohjeet

Kasutusjuhend

Vartotojo žinynas

Lietošanas instrukcija

Instrukcja obs³ugi

Uživatelská pøíruèka

Használati utasítás

Instrucţiuni

Navodila za uporabo

Užívatel’ská príruèka

Upute za uporabu

Èíñòðóêöèè çà èçïîëçâàíå

Kullanýcý Talimatlarý

Oäçãßåò XñÞóçò

KKvvttyyrrhhttkkssmmbbwwvvmmyywwttvvaarrvvhh

™

SPEEDGLAS

™

9002

Parts List

40 11 90

40 18 90

40 11 95

40 18 95

16 60 00

16 50 10

42 20 00

17 10 20-23

42 80 00

42 80 10

42 80 20

42 80 30

42 80 40

42 80 50

43 20 00

43 10 00

42 60 00

42 70 00

42 70 71

16 75 20

16 75 25

16 80 00

16 80 10

16 50 20

16 40 09

16 40 05

43 20 15

16 91 00 16 90 01

User manual 3MTM SpeedglasTM 9002

0196

Notified body 0196 DIN CERTCO

Prüf- und Zertifizierungszentrum Aalen

Augenschutz und Persönliche Schutzausrüstung

Gartenstraße 133, 73430 Aalen, Germany

1ïUser Instruction . . . . . . . . . . . . . . . . . . . . . . . page 5-14

3Bedienungsanleitung . . . . . . . . . . . . . . . . . . . . . . . Seite 15-24

2Notice d’instructions . . . . . . . . . . . . . . . . . . . . . . . page 25-33

rÈíñòðóêöèÿ ïî ýêñïëóàòàöèè

. . . . . . . . . . . .

ñòðàíèöà 34-42

u²íñòðóêö³ÿ ç åêñïëóàòàö³¿

. . . . . . . . . . . . . . . . .

ñòîð³íêà 43-51

4Instruzioni d’uso . . . . . . . . . . . . . . . . . . . . . . . . . Pagina 52-60

6Gebruiksaanwijzing . . . . . . . . . . . . . . . . . . . . . . pagina 61-69

5Instrucciones de uso . . . . . . . . . . . . . . . . . . . . . página 70-78

-Instruções de uso . . . . . . . . . . . . . . . . . . . . . . . . página 79-87

9Bruksanvisning . . . . . . . . . . . . . . . . . . . . . . . . . . . . side 88-95

7Bruksanvisning . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sida 96-104

8Brugsanvisning . . . . . . . . . . . . . . . . . . . . . . . . . . . . side 105-113

0Käyttöohjeet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . sivu 114-121

éKasutusjuhend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lk. 122-130

|Vartotojo žinynas . . . . . . . . . . . . . . . . . . . . . . . puslapis 131-138

lLietošanas instrukcija . . . . . . . . . . . . . . . . . . . lappuse 139-147

HInstrukcja obs³ugi . . . . . . . . . . . . . . . . . . . . . . . . strona 148-157

FUživatelská pøíruèka . . . . . . . . . . . . . . . . . . . . . . strana 158-166

JHasználati utasítás . . . . . . . . . . . . . . . . . . . . . . . . . oldal 167-175

LInstrucţiuni . . . . . . . . . . . . . . . . . . . . . . . . . . . . . paginæ 176-184

SNavodila za uporabo . . . . . . . . . . . . . . . . . . . . . . . stran 185-192

DUžívatel’ská príruèka . . . . . . . . . . . . . . . . . . . . . . strana 193-201

AUpute za uporabu . . . . . . . . . . . . . . . . . . . . . . . . . strana 202-210

KÈíñòðóêöèè çà èçïîëçâàíå . . . . . . . . . . . . . . . . . . ñòð. 211-219

:Kullanýcý Talimatlarý . . . . . . . . . . . . . . . . . . . . . . . . Sayfa 220-227

=Oäçãßåò ×ñÞóçò . . . . . . . . . . . . . . . . . . . . . . . . . Óåëßäá 228-236

iKKvvttyyrrhhttkkssmmbbwwvvmmyywwttvvaarrvvhh. . . . . . . . . . . . . . . . . . . MMyyddvvmmii237-244

Instruction Speedglas 9002

BEFORE WELDING

For your own protection read these instructions carefully before

using Speedglas 9002.

Assemble the equipment according to the illustrations in this

manual. The complete equipment is illustrated in figure A:1

Adjust the welding shield according to your individual require-

ments. The headband should be adjusted both in diameter and

height. The angle between face and shield should also be adju-

sted and is recommended to be 10°-12° according to figure A:2

All Speedglas automatically darkening welding filters are desi-

gned to be used in arc welding or gas cutting applications. The

unit is suitable for all arc welding processes such as MIG, MAG,

TIG, MMA, Plasma Arc, and Air Carbon. The welding filter can

also be used for gas welding when the filter is in the “off” state,

shade 5-6.

The shade number in the dark state is marked on the product. The

suitable shade number should be chosen according to EN 379

(also available in EN 169).

Speedglas 9002 automatically darkening welding filter gives

permanent protection (shade13) against harmful UV- and IR-radia-

tion, regardless if the filter is in the light or dark state and also in

the event of battery or electronic failure.

The welding filter has two photo sensors that react independent-

ly as the welding arc is struck and causes the filter to darken. Two

lithium batteries (3V CR2032) are used as the power source.

Speedglas 9002X has an additional solar panel for extended bat-

tery lifetime. The welding filter is automatically switched off appro-

ximately 60 minutes after the last time the arc was struck.

1 ï

Note!

The Speedglas 9000 welding shield should always be used

together with original Speedglas spare parts such as inner and

outer protection plates, part numbers according to parts list.

The use of non Speedglas components might impair protection

and will void warranty claims and approvals.

Note!

Speedglas 9000 welding shields are not suitable for laser welding

or laser cutting. Speedglas 9000 welding shields are suitable

for all positions except heavy duty overhead cutting/welding

operation due to the risk of molten metal.

Markings

The welding filter is marked with the shade range.

The eye and face protection classification is made according to

EN 379, EN 166, EN 169 and EN 175.

The following is an example (EN 379):

Note! The above is an example. Valid classification is marked on

each product.

On the welding shield and the outer protection plate, marking can

be found that indicates safety class for protection against high

1ï

Light shade

3 / 9-13 3M 1 / 1 / 1 / 2 / EN379 CE

Dark shade(s)

Manufacturer identification

Optical class

Diffusion of light class

Variations in Luminous transmittance class

Angle dependency class (optional marking)

Certification mark or number of standard

speed particles. F stands for low energy impact and B stands for

medium energy impact. If the protection meets the requirements

at extremes of temperature (-5°C to +55°C) the marking is

completed with the letter T.

Additional markings on the product refer to other standards.

Storage

The equipment should be stored in a clean and dry environment,

temperature range -30°C to + 70°C and relative humidity less

than 90 % RH.

FUNCTIONS

On/Off (Figure B)

To activate the welding filter, press the ON button. After each short

press of the ON button, the current settings (shade, sensitivity and

delay) are displayed by flashing LED’s. The welding filter is swit-

ched off approximately 60 minutes after welding has been com-

pleted. The welding filter can also be switched off manually by

pressing the ON button for a few seconds.

Selection of Shade Number setting

In order to see which Shade Number the welding filter is current-

ly set to, momentarily press the Shade button. To reselect ano-

ther Shade Number, press the Shade button again while the LED

is flashing, and then keep pressing the button to increment the

flashing LED to the correct Shade Number.

Speedglas 9002V, 9002X

Five different Shade Number settings are available in the dark

state, 9, 10, 11, 12 and 13.

Speedglas 9002D

Two different Shade Number settings are available in the dark

state, 9 and 11.

1 ï

Setting of detector Sensitivity function

Setting the performance of the photo detector system (which res-

ponds to the light from the welding arc) is made with the Sensitivi-

ty button. In order to see which position the welding filter is current-

ly set to, momentarily press the Sensitivity button. To select ano-

ther setting, press the Sensitivity button again while the LED is flas-

hing, and continue to press until the LED shows the desired setting

Speedglas 9002V, 9002X

Position 1 Least sensitive setting. Used if there is disturbing light

from other welders in the vicinity.

Position 2 Normal position. Used for most types of welding

indoors and outdoors.

Position 3 Position for welding with low current or where the

welding arc becomes stable. (eg TIG welding at low

amps)

Position 4 Extreme photo detector sensitivity. Suitable for very

low current welding or pipe welding where part of the

arc is obscured from view.

Speedglas 9002D

Position - Normal position. Used for most types of welding indo-

ors and outdoors.

Position + Position for welding with low current or where the

welding arc becomes stable. (eg TIG welding at low

amps)

Finding the right setting of detector

Speedglas 9002V, 9002X

In order to find a suitable sensitivity setting for the detector, start

with the setting, before welding, in Position 2. This is a normal

position that functions in the majority of situations. If the filter does

not darken during welding as desired, raise the sensitivity to Posi-

tion 3 or 4 until a definite shift to dark position takes place. Should

1ï

a too high sensitivity be selected, it is possible that the filter

remains in the dark position after welding is complete due to sur-

rounding light. Should this arise, make an adjustment to a less

sensitive setting where the welding filter both darkens or lightens

as desired. If the welding filter functions well in Position 2, but dar-

kens due to another welding process being in progress in the vici-

nity, select Position 1.

Speedglas 9002D

In order to find a suitable sensitivity setting for the detector, start

with the setting, before welding, in – position. This is a normal

position that functions in the majority of situations. If the filter does

not darken during welding as desired, raise the sensitivity to

+position.

Setting of the Delay to the light state

(Speedglas 9002V/9002X)

The Delay setting controls how fast the filter returns to the light

state after welding has finished. In order to see which position it

is currently set to, momentarily press the Delay button. To select

another setting, press the Delay button again while the LED is

flashing, and continue to press until the LED increments to the

desired setting.

Position - This position causes the filter to return to the light

state very rapidly and is used for example in spot or

tack welding where the welder needs to have a clear

view quickly after finishing the weld.

Position I Normal position.

Position + This position extends the delay time almost doubling

it over the normal setting and is for use in situations

where the weld pool is extremely bright after finishing

the weld.

1 ï

Andere Handbücher für Speedglas 9002

Inhaltsverzeichnis

Sprachen:

Andere 3M Schweißsystem Handbücher

3M SPEEDGLAS SL Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung