4qd JSK-120 Bedienungsanleitung
JSK-120 V1.0 05/21 Page 1 ©4QD Ltd www.4qd.co.uk
Instruction Manual
JSK-120
Contents
Section Page Section Page
1. Description................................. 1
2. Mounting..................................... 2
3. Connections............................... 2
4. Calibration ..................................2
5. Disassembly...............................3
1. Description
The JSK-120 is a single axis joystick designed for use with our Pro-160 /
360 series controllers.
It has a hall effect sensor for long life.
It has a removable detent to identify the center off position.
It has a removable end stop to limit the travel to 120 degrees.
All parts are replaceable.
JSK-120 V1.0 05/21 Page 2 ©4QD Ltd www.4qd.co.uk
2. Mounting
The JSK-120 requires a 47mm diameter hole in the mounting panel. There is no
limitation on the panel thickness.
3. Connections
The JSK-120 uses the Vishay 981HE sensor and the wiring colours are somewhat
counter intuitive….
Green = +5V
Red = Signal
Yellow = Ground [0V]
These should be connected to the Pro-160 / 360 control board as follows.
4. Calibration
The Pro-160 / 360 should have the throttle setting / input mode set to “volt”.
If the center detent is being kept, joystick mode should be set to “on”.
The pot learn procedure should then be carried out as described in the
controller manual.
JSK-120 V1.0 05/21 Page 3 ©4QD Ltd www.4qd.co.uk
5. Disassembly
The JSK-120 can be dismantled as follows.
1. Insert a 1.5 mm allen key through the collar hole into the drum grub screw.
2. Undo the M4 handle retaining screw.
3. Place the JSK-120 handle side down and lift off the collar / drum / sensor
assembly. Take care to retain the ball bearing, spring and serrated washer.
4. Loosen the drum grub screw and the sensor holding screws, then separate
the parts.
Collar
Handle
Drum
Sensor
Lever
JSK-120 V1.0 05/21 Page 4 ©4QD Ltd www.4qd.co.uk
6. Reassembly
1. Insert the M4 handle retaining screw into the handle and place the handle
face down. Drop the serrated washer onto the part of the screw still visible.
2. Place the spring into its hole and position the ball bearing on top.
3. Apply silicon grease to the bearing surfaces of the drum and insert it into
the collar with the grub screw aligning with the hole. Insert an allen key
through the hole into the grub screw.
4. Place the collar and drum assembly onto the handle.
5. Carefully pick up all three parts and tighten the handle retaining screw.
6. Insert the sensor shaft into the drum, the wires should be at the top,
nearest to the grub screw, the shaft flat should align with the grub screw.
7. Fit the sensor holding screws and then gently tighten the grub screw.
Inhaltsverzeichnis
Andere 4qd Controller Handbücher
4qd
4qd Uni Series Bedienungsanleitung
4qd
4qd pro-150 Bedienungsanleitung
4qd
4qd 4QD Series Bedienungsanleitung
4qd
4qd PRO-160 Series Bedienungsanleitung
4qd
4qd Pro-120 Series Bedienungsanleitung
4qd
4qd PRO-160 Series Bedienungsanleitung
4qd
4qd PRO-360 Series Bedienungsanleitung
4qd
4qd pro-150 Bedienungsanleitung
4qd
4qd VTX Series Bedienungsanleitung
