A & H AMFLOW A6 Bedienungsanleitung
A & H Enterprises, Inc.
11812 NE 116th Street
TEL:
+425.883.4040
Kirkland, WA 98034 USA
FAX:
+425.823.1962
www.amflow.com
EMAIL:
QUICK START: H1 WIRING
Copyright©2015 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. C, 09/15
Page 1 of 17
Amflow®
AMFLOW®
A6 VALVE ACTUATOR
A6 Quick Start: H1
CONTENTS
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. A, 07/16
Page 2 of 17
AMFLOW®
Contents
1. What is Included
2. Installation: Actuator
3. Installation: Valve
4. Wiring: H1
5. Caution Information
6. Safety Information
7. Support
8. Representatives
A6 Quick Start: H1
WHAT IS INCLUDED
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. A, 07/16
Page 3 of 17
AMFLOW®
What is included with your Amflow®product?
☐ACTUATOR: A6
Actuator
Adjustment Handle
Adjustment Handle Mounting Screw & Lockwasher
Installation Manual & Service Manual
A6 Quick Start: H1
INSTALLATION
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. A, 07/16
Page 4 of 17
AMFLOW®
Installation: Actuator
Step 1
Cut-out panel for mounting per instructions in Installation
Manual.
A6 Quick Start: H1
INSTALLATION
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. A, 07/16
Page 5 of 17
AMFLOW®
Step 2
Attach actuator base plate assembly to front of panel.
Step 3
Mount actuator to base plate assembly using M6x16 SHCS.
A6 Quick Start: H1
INSTALLATION
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. A, 07/16
Page 6 of 17
AMFLOW®
Step 4
Prior to installing valve, confirm handle is in manual position.
AUTOMATION MODE
(Handle at Side)
MANUAL MODE
(Handle at Front)
A6 Quick Start: H1
INSTALLATION
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. A, 07/16
Page 7 of 17
AMFLOW®
Installation: Valve
Step 1
Place FLANGE ADAPTOR onto VALVE STEM prior to installation.
Step 2
Insert VALVE ADAPTOR LINK into FLANGE ADAPTOR.
Place valve into BEARNG HOUSING.
VALVE ADAPTOR LINK
FLANGE ADAPTOR
BEARING HOUSING
VALVE ADAPTOR LINK
A6 Quick Start: H1
INSTALLATION
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. A, 07/16
Page 8 of 17
AMFLOW®
Step 3
While valve is being inserted into BEARING HOUSING; rotate
valve to align VALVE ADAPTOR LINK while handle is in manual
mode.
Step 4
Once properly aligned and engaged, tighten three (3)
SETSCREWS to lock valve in place.
SETSCREWS
SETSCREWS
A6 Quick Start: H1
INSTALLATION
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. A, 07/16
Page 9 of 17
AMFLOW®
Controls: Applicable to AM7E-001 Valve Only
There are two controls used to operate the AM7E-001 flow control valve:
The first control is the SWITCH by which the operator can select
a high or low flow range.
The second is the flow rate ADJUSTMENT KNOB. This control
knob allows the operator to set a desired flow rate in either the
high flow or low flow range.
AM7E-001 ADAPTOR with
SWITCH
View of AM7E-001
looking up from bottom of OUTLET BODY
toward bottom of ADAPTOR
A6 Quick Start: H1
WIRING
Copyright©2016 A & H Enterprises, Inc.
All rights reserved
00000329-0900-013 * Rev. A, 07/16
Page 10 of 17
AMFLOW®
ACTUATOR WIRING: H1
Step 1
Provide 24VDC supply capable of providing up to 3 amps
current.
Step 2
Requires a minimum of 5 connections for H-1 operation.
Step 3
Requires a minimum of 9 connections for set-up , Industrial
Ethernet and H-1 communication.
Terminal block wiring reference for field connections
WARNING
Incorrect wiring may damage the unit!
Inhaltsverzeichnis
Andere A & H Controller Handbücher
