A-Neuvideo HD-44G Bedienungsanleitung

ETHERNET (TCP)

SET UP GUIDE V 1.0

INSTRUCTION MANUAL

A-NeuVideo.com | Frisco, Texas 75034 | (317) 456-2461

Ethernet Guide

This document only applies to A-Neuvideo products that have a built-in Ethernet Port.

Thank you for purchasing theA-Neuvideo product. You will ﬁnd this unit easy to install and highly reliable. It is essential

that you read this manual thoroughly before attempting to use it.

INTRODUCTION

The Ethernet port (TCP) allows control of the unit via a computer by redirecting serial commands (COM port) to the unit’s IP address. To

do this, you must:

(1) Install the unit and your computer on the same sub-network . (Step 1~4)

(2) Locate the Routing Control software on the supplied CD and install it on the computer. (Step 5)

Follow the steps below and you will be able to use theAP to control the unit.The default IP address of the unit is 192.168.1.3. If your PC is

not on the same sub-net, you must ﬁrst change your computer’s IPaddress to allow access to the unit. Once this is done, you can change

the IP address of the unit and then restore your computer’s IP address.

A-Neuvideo products with Ethernet port are designed for remote control on a network using our included GUI software. The Ethernet port

is not a web server for direct access via a web browser.

SETUP THE NETWORK (1)

STEP 1. NETWORK THE UNIT

(1-1) Set up the network of the unit.

(1-1.1) Plug the unit into a power outlet.

(1-1.2) Plug the Ethernet cable to the unit and the other end to an open port on your hub.

(1-1.3) Turn the unit on.

(1-2) Set up your computer in the same network of the unit.

(1-2.1) Go to start and click on control panel.

(1-2.2) Double click on Network Connections.

(1-2.3) Click on Properties.

(1-2.4) Click to select Internet Protocol (TCP/IP) and click Properties.

(1.2-5) Make note of the numbers for IP address and Default gateway.

(1.2-6) Choose use the following IP address and key in the IP number of the unit:

IP address: 192.168.0.x Default Gateway: 192.168.0.x

The ﬁrst three numbers must be 192.168. 0 while the last number must not be: number 3; lower than 255; one that has been

assigned to another device. After the numbers are set, press enter.

1. You can also locate the unit on any

network provided you setup port forwarding

on your router.

2. You can also use an external controller

provided it is capable of communication to

a COM portAND you can install the re-direct

software.

Picture 1-2.3 Picture 1-2.4

Picture 1-2.6

SETUP THE NETWORK (2)

STEP 2. CHANGE THE IP ADDRESS OF THE UNIT

(2-1) Open the A-Neuvideo AP and enter ﬁnd Ethernet Settings ﬁnd Setting. Click Search to detect the presence of the unit. Click on

the detected IP of the unit. If the unit is not detected, return to Step 1 and reset the IP address of your computer.

(2-2) After you click the unit IP, the box will be checked off. Then, you can begin to select the options on the left. Look for the Network

Settings area, get the DHCP Server to Enable. Then, change the ﬁrst three numbers of Static IP Address and Static Default Gateway

to the ones noted in step 1.2-5. Then, click Submit. (If the IP address 192.168.1.3 has already been in use in your network, you have to

assign a different number to the unit, for example, 192.168.1.6.)

Enter Ethernet Settings ﬁnd Setting. Unit IP detected

SETUP THE NETWORK (3) (4)

STEP 3. RETURN TO THE ORIGINAL IP ADDRESS

(3-1) Repeat Step 1 to reset the network of your computer. Let all the numbers of the IP address and the Default gateway match those

noted in step 1.2-5. This step shall bring your computer to the original network.

STEP 4. CONNECT THE UNIT TO THE NETWORK

(4-1) Open the AP again. Go to the Ethernet Settings ﬁnd Setting.

(4-2) Click Search to detect the unit IP.

(4-3) Then, click the unit IP to check off the box.

(4-4) Next, click Connect. Wait for a few seconds for the Connected sign to show up.

(4-5) After Connected appears, click Exit to close the window.

AP OPERATION (5)

AP OPERATION

STEP 5. START USING THE AP

Interface Introduction:

The left side shows the 7 input signals and the right shows the 5 resolution options.

Use POWER to turn on and off the unit.

Use STATUS to see the current input and output status.

Use ENTER to conﬁrm your connection from input to output.

(5-1) Click your source input signal on the left.

(5-2) Click your target resolution on the right. Aline will be

formed to show connection.

(5-3) Click ENTER.

(5-4) When the red line turns blue, the operation is done

Note: If the unit is not receiving the signal you select,

the operation will fail.

Picture 5-4: The input VGA signal has been

successfully set to display in WXGA

resolution.

Andere Handbücher für HD-44G

Inhaltsverzeichnis

Andere A-Neuvideo Schalten Handbücher

A-Neuvideo

A-Neuvideo ANI-8PDU-24V Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-PS112 Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-8MFS Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-MINI601HD Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-PS112 Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-H-KIT Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-1x2COMPDA Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-PiP-41UHD Bedienungsanleitung

A-Neuvideo

A-Neuvideo HD-88CT-A Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-5MFS Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-23TCDTX/RX Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-PIP-44UHD Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-1201HD Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-1201HD Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-4KHPN Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-QUAD-LITE-4K Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-16-4K60-S Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-QUAD-MINI Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-88UHD Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-44VGA Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-8X2MFS Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-PiP-41UHD Bedienungsanleitung

A-Neuvideo

A-Neuvideo HD-88 Series Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-3AUTOHDMI Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch