AAXA Technologies M2 Bedienungsanleitung

Table of Contents 1

Warnings 2

Package Contents 3

Product Overview 4

Keypad & Remote Control Functions 5

General Operation 6

External Inputs 9

PMP Menu System 11

Videos 12

Pictures 14

Music 16

eBooks 19

Games 21

Settings 25

Troubleshooting 27

Specications       28

Table of Contents

Warnings

*Do not operate the Projector in direct sun-

light or near heat sources such as heaters,

res, and stoves as this may cause a re

hazard.

*Do not operate the projector close to

sources of steam or oil such as a humidi-

erasthismaycauseelectricshock.

*Do not operate the projector near water such as by the sink or bathtub

as this may cause electric shock.

*Donotblockorrestrictairowfromventilationholesasthismaycause

the projector to overheat.

*Do not place inammable materials beside the projector as this may

causearehazard.

*Do not drop the projector or allow heavy impacts or shock as this will

damage the projector.

Package Contents

Projector Remote Control Tripod

Composite A/V Cable USB Cable

Power Cord VGA Cable

Product Overview

Projection Lens

Focus Adjustment

Keypad Controls

Power Button

VGA A/V

Input Input

Headphone/

Speaker Out

USB Input SD-HC Reader

Power Input HDMI Input

Keypad & Remote Control Functions

Navigation Buttons

(Play = Select/Enter)

Exit/Back

(Quick Press)

Open Menu

(Long Press)

Source Select

Power On/Off

Display Settings Menu

System Navigation &

Volume Controls

Flip Vertical Image

Flip Horizontal Image

Media Player Menu

Select Source

Mute Sound

Adjust Vertical Keystone

PMP Volume Up

PMP Menu Navigation

PMP Volume Down

General Operation

Turning on the projector

To turn on the projector rst plug the power supply into a suitable wall outlet

and to the rear of the projector. Then power the projector on by holding the

power button for 3 seconds until the optical engine turns on.

Shutting down the projector

To shut down the projector, press and hold the power button for 3 sec. The

optical engine should shut off and the fan should stop spinning.

Adjusting focus

To adjust the focus, spin the focus wheel up or down

until the image becomes clear. The recommended

focus distance for this projector is 18” to innity.

Projection lens

The projection lens emits the image from the projector. Make sure there is

nothing obstructing the lens to obtain a clear image.

Keypad Controls

Use the keypad control buttons to navigate through

each menu. The control panel behaves differently in

each submenu. Controls for submenus are explained

later in this manual.

General Operation

Accessing the Onboard Memory

The M2 Micro Projector includes 1GB of

onboard memory. To access this memory,

connect a USB cable from your computer

to the back of the projector in the slot that

reads “USB”. A folder will appear on your

computer screen after the projector is

detected. You can store any type of supported photos, video and/or les in

this folder to view.

Note: If your computer fails to detect the projector, check to make sure the

cable is securely inserted on both sides. If you’re still unable to view the

folder, please consult with your operating system’s owner manual.

Accessing a SD Memory Card

Multimedia le can also be accessed via

an SD memory card. To access your SD

card, insert it into the back of the projector

in the slot that reads “SD”. Once your SD

card has been inserted, you can navigate

through the main menu to select what you

want to view under each submenu.

*Review the Specications section of this manual to read about supported le

formats.

General Operation

Accessing a USB Storage Device

In addition to data transfer with the

onboard memory, the M2 has the ability to

read data from a USB storage devices

(such as memory sticks, cell phones, USB

hard drives, etc). This allows the user to

view the data stored on the USB storage

device through the onboard media player.

To access data on your USB storage device,

plug your USB device into the USB slot on the back of the M2. The supplied

mini USB adapter cable may be required for some USB thumbdrives.

Once the connection is made, select USB Host Mode in one of the PMP me-

dia players submenus (Videos, Photos, etc). After selecting USB Host Mode

you should now be able to access the data on the USB device through the

onboard media player. If the data does not appear, check the formating of

the le system on the USB device and also conrm that the device is com-

patible with a USB On-The-Go host device.

External Inputs

The M2 micro projector can be toggled to accept different types of inputs.

This includes VGA (Mini VGA), HDMI and Composite Video (3.5mm jack). To

toggle through the sources, press the far right button on touchpad or the

input button on the remote control to select the appropriate source.

To Connect to a VGA Source

The projector can accept a VGA input signal.

Connect the VGA cable to your source and

the other end should be inserted in the slot

on the side of the projector that reads ‘VGA’.

Toggle through the input sources and once

you select VGA input, your display should

appear.

Important: Be sure to setup the computer to enable a video signal output.

On some laptops this is done by pressing and holding Function F5 Key. If

using the M2 as an external monitor on Windows based systems, this can be

done by selecting “extend my desktop to this monitor”. The native resolution

of the M2 projector is XGA (1024 x 768) and it accepts up to a 1600x1200

signal. Depending on the video driver different resolutions many need to be

selected for proper output.

Note: Each computer system is different - please check with your owner’s

manual for how to properly output video signals. Some Apple computers may

requre a DVI to VGA adapter.

External Inputs

To Connect to a Composite Video Source

The projector can accept a compositive video

signal. This signal is comes through the 3.5mm

composite A/V cable. Connect the composite

A/V able to the projector and the other end into

the video source. Toggle through the input

sources and once you select AV input, your

display should appear.

To Connect to an HDMI Source

The projector can accept a digital HDMI input

signal. This is done by connecting the HDMI

cable to the HDMI input port of the projector.

Toggle through the input sources and once you

select HDMI input, your display should appear.

The M2 accepts up to a HDMI 1.2 signal.

Andere Handbücher für M2

Inhaltsverzeichnis

Andere AAXA Technologies Projektor Handbücher

AAXA Technologies

AAXA Technologies ST200 Bedienungsanleitung

AAXA Technologies

AAXA Technologies M1 Standard Bedienungsanleitung

AAXA Technologies

AAXA Technologies P700 Bedienungsanleitung

AAXA Technologies

AAXA Technologies P2 Jr Pico Bedienungsanleitung

AAXA Technologies

AAXA Technologies M7 Bedienungsanleitung

AAXA Technologies

AAXA Technologies P3 Pico Bedienungsanleitung

AAXA Technologies

AAXA Technologies P700 PRO PICO PROJECTOR Bedienungsanleitung

AAXA Technologies

AAXA Technologies M1 Standard Bedienungsanleitung

AAXA Technologies

AAXA Technologies P450 Bedienungsanleitung

AAXA Technologies

AAXA Technologies P7 Bedienungsanleitung

AAXA Technologies

AAXA Technologies SLC450 Bedienungsanleitung

AAXA Technologies

AAXA Technologies P4X Bedienungsanleitung

AAXA Technologies

AAXA Technologies P2-B Bedienungsanleitung

AAXA Technologies

AAXA Technologies LED PICO Bedienungsanleitung

AAXA Technologies

AAXA Technologies P4X Bedienungsanleitung

AAXA Technologies

AAXA Technologies M1 Ultimate Bedienungsanleitung

AAXA Technologies

AAXA Technologies P300 Neo Bedienungsanleitung

AAXA Technologies

AAXA Technologies P450 Bedienungsanleitung

AAXA Technologies

AAXA Technologies P4 Bedienungsanleitung

AAXA Technologies

AAXA Technologies P5 Bedienungsanleitung

AAXA Technologies

AAXA Technologies M4 Bedienungsanleitung

AAXA Technologies

AAXA Technologies HP3 Halloween Projector Bedienungsanleitung

AAXA Technologies

AAXA Technologies P2jr Pico Bedienungsanleitung

AAXA Technologies

AAXA Technologies M6 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung