ABB ACS800-37-0060-3 Bedienungsanleitung

ACS800

Hardware Manual

ACS800-37 Drives (55 to 2700 kW / 75 to 3000 HP)

ACS800-37 Drives

55 to 2700 kW (75 to 3000 HP)

Hardware Manual

3AFE68557925 REV B EN

EFFECTIVE: 01.11.2005

Safety instructions

What this chapter contains

This chapter contains safety instructions you must follow when installing, operating

and servicing the drive. If ignored, physical injury or death may follow, or damage

may occur to the drive, the motor or driven equipment. Read the safety instructions

before you work on the unit.

Usage of warnings and notes

There are two types of safety instructions throughout this manual: warnings and

notes. Warnings caution you about conditions which can result in serious injury or

death and/or damage to the equipment, and advise on how to avoid the danger.

Notes draw attention to a particular condition or fact, or give information on a

subject. The warning symbols are used as follows:

Dangerous voltage warning warns of high voltages which can cause

physical injury and/or damage to the equipment.

General warning warns about conditions, other than those caused by

electricity, which can result in physical injury and/or damage to the

equipment.

Electrostatic discharge warning warns of electrostatic discharge which

can damage the equipment.

Safety instructions

Installation and maintenance work

These warnings are intended for all who work on the drive, motor cable or motor.

Ignoring the instructions can cause physical injury or death, or damage the

equipment.

WARNING!

•Only qualified electricians are allowed to install and maintain the drive.

•The main switch on the cabinet door does not remove the voltage from the input

busbars of the drive. Before working on the drive, isolate the whole drive from

the supply.

•Never work on the drive, the motor cable or the motor when main power is

applied. After switching off the input power, always wait for 5 min to let the

intermediate circuit capacitors discharge before you start working on the drive,

the motor or the motor cable. Measure the voltage between terminals UDC+

and UDC- (L+ and L–) with a multimeter (impedance at least 1 Mohm) to

ensure that the drive is discharged before beginning work.

•Apply temporary grounding before working on the unit.

•Do not work on the control cables when power is applied to the drive or to the

external control circuits. Externally supplied control circuits may cause

dangerous voltages to exist inside the drive even when the main power of the

drive is switched off.

•Do not make any insulation or voltage withstand tests on the drive or drive

modules.

•When reconnecting the motor cable, always check that the phase order is

correct.

•When joining shipping splits (if any), check the cable connections at the joints

before switching on the supply voltage.

•Live parts on the inside of the doors are protected against direct contact.

Special attention shall be paid when handling metallic shrouds.

Note:

•The motor cable terminals on the drive are at a dangerously high voltage when

the input power is on, regardless of whether the motor is running or not.

•The brake control terminals (UDC+, UDC-, R+ and R- terminals) carry a

dangerous DC voltage (over 500 V).

•Depending on the external wiring, dangerous voltages (115 V, 220 V or 230 V)

may be present on the relay outputs of the drive system.

•The Prevention of Unexpected Start function does not remove the voltage from

the main and auxiliary circuits.

Safety instructions

WARNING!

•During the installation procedure, supply, filter or inverter modules may have to

be temporarily extracted from the cabinet. The modules have a high centre of

gravity. In order to minimise the danger of toppling over, keep the support legs

(if provided) of the modules extended whenever manoeuvring the modules

outside the cabinet. An overturning module can cause physical injury.

•Electrically conductive dust inside the unit may cause damage or lead to

malfunction. Make sure that dust from drilling does not enter the drive when

installing.

•Fastening the cabinet by riveting or welding is not recommended. However, if

welding is necessary, ensure the return wire is properly connected in order not

to damage the electronic equipment in the cabinet. Also ensure that welding

fumes are not inhaled.

•Ensure sufficient cooling of the unit.

•Cooling fans may continue to rotate for a while after the disconnection of the

electrical supply.

•Some parts inside the drive cabinet, such as heatsinks of power

semiconductors, remain hot for a while after the disconnection of the electrical

supply.

WARNING!

•The printed circuit boards contain components sensitive to electrostatic

discharge. Wear a grounding wrist band when handling the boards. Do not

touch the boards unnecessarily.

Do not tilt!

Safety instructions

Grounding

These instructions are intended for all who are responsible for the grounding of the

drive. Incorrect grounding can cause physical injury, death or equipment malfunction

and increase electromagnetic interference.

Fibre optic cables

WARNING!

•Ground the drive, the motor and adjoining equipment to ensure personnel

safety in all circumstances, and to reduce electromagnetic emission and pick-

up.

•Make sure that grounding conductors are adequately sized as required by

safety regulations.

•In a multiple-drive installation, connect each drive separately to protective

earth (PE).

•Do not install a drive equipped with an EMC (line) filter to an ungrounded

power system or a high resistance-grounded (over 30 ohms) power system.

Note:

•Power cable shields are suitable for equipment grounding conductors only

when adequately sized to meet safety regulations.

•As the normal leakage current of the drive is higher than 3.5 mA AC or 10 mA

DC (stated by EN 50178, 5.2.11.1), a fixed protective earth connection is

required.

WARNING!

•Handle the fibre optic cables with care. When unplugging optic cables, always

grab the connector, not the cable itself. Do not touch the ends of the fibres with

bare hands as the fibre is extremely sensitive to dirt. The minimum allowed

bend radius is 25 mm (1 in.).

Safety instructions

Operation

These warnings are intended for all who plan the operation of the drive or operate

the drive. Ignoring the instructions can cause physical injury or death or damage the

equipment.

WARNING!

•Before adjusting the drive and putting it into service, make sure that the motor

and all driven equipment are suitable for operation throughout the speed range

provided by the drive. The drive can be adjusted to operate the motor at

speeds above and below the speed provided by connecting the motor directly

to the power line.

•Do not activate automatic fault reset functions of the Standard Application

Program if dangerous situations can occur. When activated, these functions

will reset the drive and resume operation after a fault.

•Do not control the motor with the disconnecting device (means); instead, use

the control panel keys and , or commands via the I/O board of the drive.

The maximum allowed number of charging cycles of the DC capacitors (i.e.

power-ups by applying power) is five in ten minutes.

•Do not use the Prevention of Unexpected Start feature for stopping the drive

when the inverter unit(s) is running. Give a Stop command instead.

Note:

•If an external source for start command is selected and it is ON, the drive (with

Standard Application Program) will start immediatelyafter fault reset unless the

drive is configured for 3-wire (a pulse) start/stop.

•When the control location is not set to Local (L not shown in the status row of

the display), the stop key on the control panel will not stop the drive. To stop

the drive using the control panel, press the LOC/REM key and then the stop

key .

Safety instructions

Permanent magnet motor drives

These are additional warnings concerning permanent magnet motor drives.

WARNING! Do not work on the drive when the permanent magnet motor is rotating.

Also when the supply power is switched off, a rotating permanent magnet motor

feeds power to the intermediate circuit of the drive and also the supply connections

become live (even when the inverter is stopped!).

Installation and maintenance work

• Disconnect the motor from the drive with a safety switch

and additionally, if possible,

• lock the motor shaft and ground the motor connection terminals temporarily by

connecting them together as well as to the PE.

Operation

Do not run the motor above the rated speed. Motor overspeed leads to overvoltage

which may result in explosion of the capacitors in the intermediate circuit of the drive.

Application program

Controlling a permanent magnet motor is only allowed using the ACS800 Permanent

Magnet Synchronous Motor Drive Application Program, or using other application

programs in scalar control mode only.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ABB Controller Handbücher

ABB

ABB Totalflow mflo Series Benutzerhandbuch

ABB

ABB HF Series Bedienungsanleitung

ABB

ABB RC/A 8.2 Bedienungsanleitung

ABB

ABB GPS2436 Bedienungsanleitung

ABB

ABB ACQ580 Fehlerbehebungshandbuch

ABB

ABB Relion 620 Series Bedienungsanleitung

ABB

ABB PSTX30 370 Series Bedienungsanleitung

ABB

ABB Relion 670 series REC670 Bedienungsanleitung

ABB

ABB ACS320 series Bedienungsanleitung

ABB

ABB ACS880-07 Bedienungsanleitung

ABB

ABB ACS550-01 Bedienungsanleitung

ABB

ABB AC500 Series Bedienungsanleitung

ABB

ABB Advant Controller 450 Bedienungsanleitung

ABB

ABB ARC600 Bedienungsanleitung

ABB

ABB C1900 Series Bedienungsanleitung

ABB

ABB IRC5 Compact Bedienungsanleitung

ABB

ABB IRC5 Compact Bedienungsanleitung

ABB

ABB BSFC-02C Bedienungsanleitung

ABB

ABB IRC5 Compact Bedienungsanleitung

ABB

ABB ECA06 Kurzanleitung

ABB

ABB ACS550-01 Bedienungsanleitung

ABB

ABB i-bus KNX FCA/S 1.1M Bedienungsanleitung

ABB

ABB AC 800M Bedienungsanleitung

ABB

ABB AC500-S Montage- und Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung