ABB DOL Starter Bedienungsanleitung

Installation

Remove cover by releasing 2 off screws with a screwdriver.

Wiring to overload:

Connect leads provided from – terminal 14 to terminal 95 and terminal A2 to terminal 96

Check operating coil voltage and frequency

Remove appropriate top/bottom knockouts. Attach conduit bushes to conduit

Mount base and connect to bushes. If continuous grounding is required fit separate bonding strap. For on-site control

circuit conversions see overleaf.

Connect cables and ensure that all terminals are tight.

When installed, set the hand/auto rest selector and adjust the current calibration to the desired value.

Replace cover and re-tighten cover screws.

Note: If an extra control device is required, see overleaf.

Overload Selection

Order references

Overload

rating

Full load A

Approximate motor rating Recommended

max. fuse size for

short circuit

protection A

400V/3PH

AC3

230V/1PH

Min. Max. kW hp kW hp

TA25DU1.4 1.0 1.4 0.37 0.55 0.07 0.09 4

TA25DU1.8 1.3 1.8 0.55 0.75 0.1 0.125

TA25DU2.4 1.7 2.4 0.75 1.0 0.18 0.25

TA25DU3.1 2.2 3.1 1.1 1.5 0.25 0.33

TA25DU4.0 2.8 4.0 1.5 2.0 0.37 0.5

TA25DU6.5 4.5 6.5 2.2 3.0 0.55 0.75

TA25DU11 7.5 11.0 4.0 5.5 1.1 1.5

TA25DU14 10.0 14.0 5.5 7.5 1.5 2.0

TA25DU19 13.0 19.0 7.5 10.0 2.2 3.0

TA25DU25 18.0 25.0 11.0 15.0 3.0 4.0

TA25DU32 22.0 32.0 15.0 20.0 4.0 5.5

Note: This product is not suitable for d.c. applications.

Terminal capacity

Main Auxiliary

Contactor 1 x 4mm2

2 x 2.5mm2

1 x 4mm2

2 x 2.5mm2

Overload 1 x 10mm2

2 x 6mm2

2 x 2.5mm2

Summary

A direct-on-line motor starter with ingress protection to

IP66. Two-tone plastic enclosure with ABS lid and base.

Trip class 10 requirements IEC 947-4-1

1.05 x FLC No tripping

1.2 x FLC Trip within 2 hours

1.5 x FLC Trip within 4 minutes

7.2 x FLC Trip between 4s and 10s

NOTE: FLC = Full load current

1TVS013114P0300 Rev1 01/1

DOL Starter

Plastic Enclosure to IP65

IEC947-4-1 Issue 1

Installation Instructions

ABB

Connection Data

Type (400Vcoil) Type (230V coil)

Circuits

Standard circuit Special circuits

Line-to-line plus remote 3-wire control Two-wire controls

Fitting an extra control device

Council of European Communities Directives: The products in

this publication conform to relevant EEC Directives and EN

Standards. Installation and use of such products must be carried

out by competent, properly trained personnel, complying with any

instructions supplied by the manufacturer. Liability for improper

incorporation, assembly, use, processing, storing or handling of

goods remains the sole responsibility of the individual, or company

carrying out such work. This publication is for information only.

Whilst every care has been taken in the preparation of this leaflet,

no liability is accepted for any consequence of its use. No licence

to use any patent should be assumed. All dimensions are

approximate only and subject to change without notice, as are

other technical features resulting from continual development and

improvement.

For further information please contact your

ABB

Tec

hnical Helpline 02476 368500

Start Remote

start

Remove

link

Remote

stop

Stop/reset

Remove

link

Reset

Control

contact

4 6

Start

Stop/

reset

(A)

(B)

(C)

A knockout is provided in

the lid of the DOL for an

extra control device.

1. Remove lid of starter

2. Cut around serrated

label insert

and remove

3. Remove front 22mm

knockout.

4. Fit control device kit.

U V W

(A) (B) (C)

L1 L2 L3 E

1 3 5

2 4 6

U V W

(A) (B) (C)

N L1 L2 L3 E

1 3 5

2 4 6

N L

N L E

1 3 5

2 4 6

Note: For

Single phase

Operation link

1 to A1,

3 to 2 as shown.

Andere ABB Controller Handbücher

ABB

ABB Series Bedienungsanleitung

ABB

ABB Pulsar Edge Bedienungsanleitung

ABB

ABB Protronic 100 Bedienungsanleitung

ABB

ABB AC 31 Bedienungsanleitung

ABB

ABB ControlMaster CM30 Bedienungsanleitung

ABB

ABB TZIDC Bedienungsanleitung

ABB

ABB ACS 600 Series Bedienungsanleitung

ABB

ABB PM564-R-AC Bedienungsanleitung

ABB

ABB MS325 Bedienungsanleitung

ABB

ABB COMMANDER 310 Bedienungsanleitung

ABB

ABB FC/S 1.1 Bedienungsanleitung

ABB

ABB ACS880-01 Series Bedienungsanleitung

ABB

ABB i-bus FCC/S 1 1 Series Bedienungsanleitung

ABB

ABB i-bus KNX Bedienungsanleitung

ABB

ABB REC650 ANSI Bedienungsanleitung

ABB

ABB C310 Betriebsanleitung

ABB

ABB ACS55 Bedienungsanleitung

ABB

ABB ACS550 Series Bedienungsanleitung

ABB

ABB ACS 800 Series Gebrauchs- und Pflegehandbuch

ABB

ABB Busch-Jaeger Busch-Jalousiecontrol II Series Bedienungsanleitung

ABB

ABB ACS150 series Bedienungsanleitung

ABB

ABB 650 series Installations- und Betriebshandbuch

ABB

ABB ACB530 Series Bedienungsanleitung

ABB

ABB MS132-32-HKF1-11 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung