ABB LP Bedienungsanleitung

INSTRUCTION MANUAL

LINEAR PISTON ACTUATORS

Type “LP”

Simple Cylinder Actuators

PN25008

WARNING notices as used in this manual apply to hazards or unsafe practices which could result in

personal injury or death.

CAUTION notices apply to hazards or unsafe practices which could result in property damage.

NOTES highlight procedures and contain information which assist the operator in understanding the

information contained in this manual.

All software, including design, appearance, algorithms and source codes, is owned and copyrighted by

ABB Inc. or its suppliers.

WARNING

INSTRUCTION MANUALS

Do not install, maintain or operate this equipment without reading, understanding and following the proper

ABB Inc. instructions and manuals, otherwise injury or damage may result.

POSSIBLE PROCESS UPSETS

Operation and maintenance must be performed only by qualified personnel and only after securing

equipment controlled by this product. Adjusting or removing this product while it is in the system may

upset the process being controlled. Some process upsets may cause injury or damage.

NOTICE

The information contained in this document is subject to change without notice. ABB Inc. reserves the

right to make minor changes to this publication, such as company name & logos as well as other minor

corrections, without necessarily changing the publication number.

ABB Inc., its affiliates, employees, and agents, and the authors of and contributors to this publication

specifically disclaim all liabilities and warranties, express and implied (including warranties of

merchantability and fitness for a particular purpose), for the accuracy, currency, completeness, and/or

reliability of the information contained herein and/or for the fitness for any particular use and/or for the

performance of any material and/or equipment selected in whole or part with the user of/or in reliance

upon information contained herein. Selection of materials and/or equipment is at the sole risk of the user

of this publication.

This document contains proprietary information of ABB Inc. and is issued in strict confidence. Its use, or

reproduction for use, for the reverse engineering, development or manufacture of hardware or software

described herein is prohibited. No part of this document may be photocopied or reproduced without the

prior written consent of ABB Inc.

LP LINEAR PISTON ACTUATORS INSTRUCTION MANUAL

TABLE OF CONTENTS

READ FIRST................................................................................................................... 2

1.0 SPECIFICATIONS / FEATURES .............................................................................. 3

2.0 THRUST RATINGS................................................................................................... 4

3.0 MODEL NUMBER DETAILS ..................................................................................... 5

4.0 OUTLINE DIMENSIONS ........................................................................................... 6

2 ½ in. Sizes (LP10).................................................................................................. 6

4 in. Sizes (LP20) ...................................................................................................... 7

6 in. Sizes (LP32) ...................................................................................................... 8

5.0 PARTS ...................................................................................................................... 9

LP LINEAR PISTON ACTUATORS INSTRUCTION MANUAL

READ FIRST

WARNING

INSTRUCTION MANUALS

Do not install, maintain, or operate this equipment without reading, understanding and following the

proper ABB Inc. instructions and manuals, otherwise injury or damage may result.

RETURN OF EQUIPMENT

All equipment being returned to ABB Inc. for repair must be free of any hazardous materials (acids,

alkalis, solvents, etc). A Material Safety Data Sheet (MSDS) for all process liquids must accompany

returned equipment. Contact ABB Inc. for authorization prior to returning equipment.

Read these instructions before starting installation; save these instructions for future reference.

WARNING

Stay clear of moving components when performing procedures that require the

equipment to be energized. The equipment can operate automatically. There is a

risk of entanglement of body parts if caution is not observed. When possible,

remove the supply source or remove the equipment from the process before

servicing.

Contacting ABB Inc.

Should assistance be required with any ABB Instrumentation product, contact the following:

Telephone:

Automation Services Call Center

1-800-HELP-365

E-Mail:

ins.techsuppor[email protected]

LP LINEAR PISTON ACTUATORS INSTRUCTION MANUAL

1.0 SPECIFICATIONS / FEATURES

LP linear piston actuators are used to control the

position of air dampers or louvers on furnaces,

boilers, and air distribution systems. They are

also used on burner and SOFA Tilts. They are

suitable for Windbox damper control in NOx

reduction control systems.

Operation with TZID-C Smart Positioners offers

digital communication, self-calibration,

diagnostics and monitoring functions. The

“AutoStroke” feature calibrates and tunes itself

automatically.

FEATURES :

High resolution, sensitivity, and fast response

with proven AV and TZID-C Positioners.

• Cylinders available with Buna-N or Viton

seals.

• Temperature range up to 250oF with

AV15, 185oF with TZID-C.

• Easy adaptability to air dampers and

louvers via clevis and pivot pin

mounting.

• Drop in replacement for many “older”

piston actuators.

• Available with built-in 4 to 20ma.

position feedback.

Linear Piston Actuator Assemblies

The LP series of damper drives provide a linear

actuation solution that is ideally suited for

applications like Windbox-dampers. The

conventional assembly, which uses the AV

Positioner series, offers a high-temperature

option up to 25oF. In comparison, our digital

solution allows for operation up to 185oF, plus

the added features of digital control.

LP sizes range from a 2.5” diameter cylinder

with a 5” stroke (2.5”x 5”) up to a 12”x 14”

diameter cylinder. The most common sizes,

2.5”x 5” and 4”x 4,” are readily available.

TZID-C Digital Features

• Microprocessor-based

• Local keypad, two line LCD and

position indicator

• Easy local configuration and operation

• Digital communication via HART,

FOUNDATION Fieldbus, and Profibus

• Remote configuration and monitoring

Configurable operating parameters

• Easy set-up of direct/reverse action, limit

stops, etc.

• Integrated position feedback

• Analog and/or digital feedback without

additional external devices to calibrate and

maintain

• Diagnostics and self-monitoring capabilities

• Easy trouble-shooting and preventive

maintenance

• Immunity to shock and vibration allows

installation in high vibration areas

Simple Cylinder Actuators From 21/2” dia. x 5” Stroke

to 10”dia. x 16” Stroke

LP LINEAR PISTON ACTUATORS INSTRUCTION MANUAL

2.0 THRUST RATINGS

The basic thrust rating of a

pneumatic piston is equal to the area

of the piston times the supply

pressure. The minimum supply

pressure for both the TZID-C and the

AV1 is 20 psi.

The maximum supply pressure for

the TZID-C is 90 psi and 125 psi for

the AV positioner.

The area of the piston is A = πD2/4.

Subtract approximately 10% for

friction losses and because the rod

side of the piston has less area. An

example is shown for an 80 psi air

supply:

To find the lever length that would result

in 90orotation of the damper shaft,

multiply the cylinder stroke length by

0.707.

Please refer to the individual Product

Specifications for details on the AV

and TZID-C Positioner performance.

LP Cylinder Thrust @ 80psi

2.5” d x 5” s 353 lbs.

4” d x 4” s 905 lbs

6” d x 8” s 2036 lbs.

8” d x 16” s 3619 lbs.

10” d x 16” s 5655 lbs.

LP LINEAR PISTON ACTUATORS INSTRUCTION MANUAL

3.0 MODEL NUMBER DETAILS

“Simple Cylinder” type Linear pneumatic piston actuators are supplied with either type AV conventional

or type TZID intellegent positioners mounted on the cylinder. Cylinders are supplied with a threaded

clevis on the rod end and a standard MP pivot on the base.

The cylinders can be supplied with either Buna-N nitrile rubber seals suitable for 200oF operation or Viton

seals suitable for 300oF operation. The Buna-N seals have a lower breakaway pressure, offering

smoother modulating control. High temperature Viton seals are inherently higher friction and tend to stick

and breakaway, causing somewhat jerky motion. The operating temperature for the AV15 & AV16 is

250oF. All other positioners have a 185oF maximum ambient. Buna-N seals are recommended unless

temperatures > 200oF dictate Viton.

Please refer to the individual Instruction Books for the AV and the TZID-C for

details on the two types of Positioners.

Nomenclature: Digits 1

thru 4

5 6 7 8 9 10

Cylinder Size:

2 ½” d. X 5” stroke LP10

4” d. X 4” stroke LP20

6” d. X 8” stroke LP30

6” d X 16” stroke LP 32

8” d. X 8” stroke LP40

8” d X 16” stroke LP50

10” d X 16” stroke LP60

Buna-N cylinder seals B

Viton cylinder seals V

Positioner type

AV15, 3-15psi in, 250oF 1

AV16, 3-27psi in, 250oF 2

AV23, 4-20 ma. in, 185oF, fail safe (1) 3

TZID-C, 4-20ma. in, 185oF, fail safe A

TZID-C, 4-20ma. in, 185oF,failinplace B

No Position Feedback 0

With 4-20ma. Position Feedback (185oF) 1

No Travel Switches 0

With 2 digital switches (TZID-C only) 1

Without Manifold 0

Manifold w Bypass valve & gage ports 1

Standard clevis and pivot base w/o boot 0

Standard clevis & base with boot 1

Special Mounting X

LP LINEAR PISTON ACTUATORS INSTRUCTION MANUAL

4.0 OUTLINE DIMENSION DRAWINGS

(Certified Drawings available on request).

LP 10: 2.5 x 5 Linear Piston

Shown with TZID-C Smart Positioner

LP LINEAR PISTON ACTUATORS INSTRUCTION MANUAL

LP 20 : 4 x 4 Linear Piston

Shown with AV15 Positioner.

LP LINEAR PISTON ACTUATORS INSTRUCTION MANUAL

LP 32 : 6 x 16 Linear Piston

Shown with AV15 Positioner.

Inhaltsverzeichnis

Andere ABB Controller Handbücher

ABB

ABB SA-M 16.2.2 Series Bedienungsanleitung

ABB

ABB C1900RC Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

ABB

ABB MotiFlex e180 Benutzerhandbuch

ABB

ABB RELION 650 SERIES Kurzanleitung

ABB

ABB MS116 Bedienungsanleitung

ABB

ABB i-bus FCC/S 1 1 Series Bedienungsanleitung

ABB

ABB COMMANDER 300 Betriebsanleitung

ABB

ABB RHD8000 Series Bedienungsanleitung

ABB

ABB RVC Bedienungsanleitung

ABB

ABB ACQ80-04 Series Bedienungsanleitung

ABB

ABB Jocab Safety Vital 2 Bedienungsanleitung

ABB

ABB ACS 601 Bedienungsanleitung

ABB

ABB ACS 600 MultiDrive Bedienungsanleitung

ABB

ABB ACS550 Series Bedienungsanleitung

ABB

ABB Pulsar Edge Bedienungsanleitung

ABB

ABB AC500-S Montage- und Bedienungsanleitung

ABB

ABB ACS880-07 Bedienungsanleitung

ABB

ABB Ability BECL/D.200.16 Bedienungsanleitung

ABB

ABB S4Cplus Bedienungsanleitung

ABB

ABB COMMANDER 500 Bedienungsanleitung

ABB

ABB ACS310 Installations- und Betriebsanleitung

ABB

ABB ACS580-04 Bedienungsanleitung

ABB

ABB ACS880-07 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung