ABB PLUTO Safety-PLC Benutzerhandbuch

1 2TLC172007M0203_B.doc

Startup guide for Pluto Safety PLC, connected in a bus system

1. Check the bus cable

·How many meters of bus cable have been

used?

·Is the system connected with stub

cables?

·How long is each stub?

·What is the total length of stub cables?

·Resistors for end termination must only

be connected in the beginning and the

end of the system.

·When measuring the resistance between

CH and CL at one Pluto (all units shall be

dead) the resistance shall be somewhat

under 60 Ω.

The following data are necessary to select the correct communication speed in the system. A lower speed

gives the possibility to communicate over a longer distance, but it results in that somewhat fewer Pluto’s can

be connected. A more detailed description can be found in the Pluto Hardware Manual, chapter Bus

communication.

Bus speed

Cable length

Stub length

Total stub length

100 kbit/s 600 m 25 m 120 m

125 kbit/s 500 m 20 m 100 m

200 kbit/s 300 m 13 m 70 m

250 kbit/s 250 m 10 m 50 m

400 kbit/s 150 m 6 m 30 m

500 kbit/s 100 m 5 m 25 m

800 kbit/s 60 m 3 m 15 m

1 Mbit/s < 20 m 1 m 5 m

Communication speed for the project is set in the Pluto Manager. Open the window Project NoName, open

the pop-up menu under Baudrate Pluto Canbus and select the correct speed.

2. Read the IDFIX number

·Must be performed before the program is downloaded to any of the units.

·The programming cable must be connected to each Pluto when reading that particular Pluto’s IDFIX.

·Read IDFIX numbers to all Pluto’s using the command “Copy online IDFIX to clipboard” under the

menu “Tools”. Paste the number to the corresponding Pluto.

2 2TLC172007M0203_B.doc

3. Check the Operating System version

·To avoid problems with different OS versions in the Pluto

system, it is a good idea to check that the correct version

of the OS is downloaded to all Pluto units. The most

convenient way to do this is with “OnlineInfo →Pluto

connected to PC” under the “Tools” menu.

The latest version of OS can be obtained by contacting support.jokabsaf[email protected].com or your local ABB

Jokab support.

4. Check that Er20 is shown in the Pluto display window

·If another fault code is shown in the display window; the program shall be erased from the unit,

resulting in Er20 shown on the display. If another fault code is shown, the Pluto can be restarted with

voltage off/on or with the command “Reset all Pluto’s” under the “Tools” menu.

·Repeat the procedure for all units in the system.

5. Download the program

·Compile and download the project file in one of the Pluto units. Check that all units have the program

downloaded in the window that is shown. Pay attention to the units that eventually have not been

correctly loaded. Select “Start PLC program”.

·Fault code Er26 is going to be shown in the Pluto display. This is normal and is acknowledged with

the “Reset all Pluto’s” command under the “Tools” menu or with voltage off/on at all units.

·Check the system with the “Bus Status” command under the “Tools” menu. All units shall be

green/OK. If there are fault codes, check in the manual and perform necessary measures.

3 2TLC172007M0203_B.doc

Problems due to communication and downloading of programs in the network

·If the Pluto units in the “Bus Status” window is flashing red/green and showing the fault code Er18

and some other fault codes (among others Er24, Er27 and Er60) it is probable that the bus cable is

not correctly connected/installed or that a Pluto unit is causing disturbances on the bus.

·Start by disconnecting the upper left connection block at all Pluto units (put a screwdriver in the slot

on the contact block and lift the block upwards). For each and every of the units, switch off and on

the voltage and download the program again without connecting the Pluto to the bus. Check that the

correct station number is shown on all units. N.B.! Make no changes in the program and no

compilations in this stage. All units must be loaded with exactly the same project.

·Check the connections of the bus cable to the Pluto units. All CH shall be connected to each other

and all CL shall be connected to each other. The ends of the cable shall be equipped with

termination resistors of 120Ωeach.

·If the length of the bus cable is not possible to read/estimate it is possible to measure the bus cable

with a multimeter. Create a short circuit at one end of the bus cable and measure the resistance

between the two conductors for CH and CL without a termination resistor in the other end. When

performing the measurement all Pluto’s must be powered off and the terminal block for the bus

connection shall be disconnected.

Total resistance = resistivity * total cable length * 2/ cable area

For copper with the area 0,5 mm2the resistivity is 0,0172 mm2/m.

Example:

With a total resistance of 10,3Ωthe cable length will be approximately 150m.

·Now reconnect one Pluto at a time and check in the “Bus Status” window that the units are shown

and are OK. The fault code Er18 can be shown; try to reset by pressing the button “K” at the Pluto or

make a “Reset all Pluto’s” to get started again. If this doesn’t help; replace the last Pluto that was

connected with another unit, which must have the program downloaded before being connected.

·All Pluto units in a project are loaded with the same program. The IDFIX number determines which

part of the project that is being executed for the particular Pluto. This can be a help for

troubleshooting: Pluto units can be changed around to see if the fault follows a particular Pluto or

not.

10,3*0,5

0,0172*2 =149,7

Andere Handbücher für PLUTO Safety-PLC

Inhaltsverzeichnis

Andere ABB Controller Handbücher

ABB

ABB ACS880 Series Bedienungsanleitung

ABB

ABB PST30 Bedienungsanleitung

ABB

ABB AC500 Series Referenzhandbuch

ABB

ABB DCT880 Bedienungsanleitung

ABB

ABB ACS880-07 Bedienungsanleitung

ABB

ABB PSE18 Bedienungsanleitung

ABB

ABB CBT-STAT Bedienungsanleitung

ABB

ABB PSTX 30***105 Bedienungsanleitung

ABB

ABB M2301 Bedienungsanleitung

ABB

ABB ACS 800 Series Benutzerhandbuch

ABB

ABB IRC5 Compact Bedienungsanleitung

ABB

ABB ACS 6000 Kurzanleitung

ABB

ABB Relion 630 Series Bedienungsanleitung

ABB

ABB UMC100.3 Bedienungsanleitung

ABB

ABB PSTX470 Bedienungsanleitung

ABB

ABB COM600 4.0 Bedienungsanleitung

ABB

ABB MotiFlex e180 Benutzerhandbuch

ABB

ABB COM600 3.4 Bedienungsanleitung

ABB

ABB ACS800 Multidrive Bedienungsanleitung

ABB

ABB ACQ580 Gebrauchs- und Pflegehandbuch

ABB

ABB ACS580-04 Bedienungsanleitung

ABB

ABB ACS55 Bedienungsanleitung

ABB

ABB ControlMaster CMF Bedienungsanleitung

ABB

ABB COMMANDER 310 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung