ABB Relion RED615 Bedienungsanleitung
Relion® 615 series
Line Differential Protection and Control
RED615
DNP3 Point List Manual
Document ID: 1MRS756879
Issued: 03.07.2009
Revision: A
Product version: 2.0
© Copyright 2009 ABB. All rights reserved
Copyright
This document and parts thereof must not be reproduced or copied without written
permission from ABB, and the contents thereof must not be imparted to a third
party, nor used for any unauthorized purpose.
The software or hardware described in this document is furnished under a license
and may be used, copied, or disclosed only in accordance with the terms of such
license.
Trademarks
ABB and Relion are registered trademarks of ABB Group. All other brand or
product names mentioned in this document may be trademarks or registered
trademarks of their respective holders.
Guarantee
Please inquire about the terms of guarantee from your nearest ABB representative.
ABB Oy
Distribution Automation
P.O. Box 699
FI-65101 Vaasa, Finland
Telephone: +358 10 2211
Facsimile: +358 10 22 41094
http://www.abb.com/substationautomation
Disclaimer
The data, examples and diagrams in this manual are included solely for the concept
or product description and are not to be deemed as a statement of guaranteed
properties. All persons responsible for applying the equipment addressed in this
manual must satisfy themselves that each intended application is suitable and
acceptable, including that any applicable safety or other operational requirements
are complied with. In particular, any risks in applications where a system failure and/
or product failure would create a risk for harm to property or persons (including but
not limited to personal injuries or death) shall be the sole responsibility of the
person or entity applying the equipment, and those so responsible are hereby
requested to ensure that all measures are taken to exclude or mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be
completely ruled out. In case any errors are detected, the reader is kindly requested
to notify the manufacturer. Other than under explicit contractual commitments, in
no event shall ABB be responsible or liable for any loss or damage resulting from
the use of this manual or the application of the equipment.
Conformity
This product complies with the directive of the Council of the European
Communities on the approximation of the laws of the Member States relating to
electromagnetic compatibility (EMC Directive 2004/108/EC) and concerning
electrical equipment for use within specified voltage limits (Low-voltage directive
2006/95/EC). This conformity is the result of tests conducted by ABB in
accordance with the product standards EN 50263 and EN 60255-26 for the EMC
directive, and with the product standards EN 60255-6 and EN 60255-27 for the low
voltage directive. The IED is designed in accordance with the international
standards of the IEC 60255 series.
Table of contents
Section 1 Introduction.......................................................................3
This manual........................................................................................3
Intended audience..............................................................................3
Product documentation.......................................................................4
Product documentation set............................................................4
Document revision history.............................................................5
Related documentation..................................................................5
Document symbols and conventions..................................................6
Safety indication symbols..............................................................6
Document conventions..................................................................6
Functions, codes and symbols......................................................7
Section 2 DNP3 data mappings.......................................................9
Overview.............................................................................................9
Point list for RED615 Ver.2.0 DE01-03............................................10
Section 3 DNP3 protocol implementation.......................................19
DNP3 device profile..........................................................................19
DNP3 implementation table..............................................................21
Section 4 Glossary.........................................................................25
Table of contents
RED615 1
Point List Manual
2
Section 1 Introduction
1.1 This manual
Point List Manual describes the outlook and properties of the data points specific to
the IED. The manual should be used in conjunction with the corresponding
Communication Protocol Manual.
1.2 Intended audience
This manual addresses the communication system engineer or system integrator
responsible for pre-engineering and engineering for communication setup in a
substation from an IED perspective.
The system engineer or system integrator must have a basic knowledge of
communication in protection and control systems and thorough knowledge of the
specific communication protocol.
1MRS756879 A Section 1
Introduction
RED615 3
Point List Manual
1.3 Product documentation
1.3.1 Product documentation set
Planning & purchase
Engineering
Installing
Commissioning
Operation
Maintenance
Decommissioning
deinstalling & disposal
Application manual
Operation manual
Installation manual
Service manual
Engineering manual
Commissioning manual
Communication protocol
manual
Technical manual
Planning & purchase
Engineering
Installing
Commissioning
Operation
Maintenance
Decommissioning
deinstalling & disposal
Planning & purchase
Engineering
Installing
Commissioning
Operation
Maintenance
Decommissioning
deinstalling & disposal
Application manualApplication manual
Operation manualOperation manual
Installation manualInstallation manual
Service manualService manual
Engineering manualEngineering manual
Commissioning manualCommissioning manual
Communication protocol
manual
Communication protocol
manual
Technical manualTechnical manual
en07000220.vsd
IEC07000220 V1 EN
Figure 1: The intended use of manuals in different lifecycles
Engineering Manual contains instructions on how to engineer the IEDs. The
manual provides instructions on how to use the different tools for IED engineering.
It also includes instructions on how to handle the tool component available to read
disturbance files from the IEDs on the basis of the IEC 61850 definitions. It further
introduces the diagnostic tool components available for IEDs and the PCM600 tool.
Installation Manual contains instructions on how to install the IED. The manual
provides procedures for mechanical and electrical installation. The chapters are
organized in chronological order in which the IED should be installed.
Commissioning Manual contains instructions on how to commission the IED. The
manual can also be used as a reference during periodic testing. The manual
provides procedures for energizing and checking of external circuitry, setting and
configuration as well as verifying settings and performing directional tests. The
Section 1 1MRS756879 A
Introduction
4RED615
Point List Manual
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere ABB Controller Handbücher
ABB
ABB SA-M 16.2.2 Series Bedienungsanleitung
ABB
ABB LME620-AI Bedienungsanleitung
ABB
ABB ACS880-01 Series Bedienungsanleitung
ABB
ABB COM600 series Merkblatt
ABB
ABB RHDE250 Bedienungsanleitung
ABB
ABB ACS550-U1-08A8-4 Bedienerhandbuch
ABB
ABB ControlMaster CM30 Bedienungsanleitung
ABB
ABB UMC100.3 Bedienungsanleitung
ABB
ABB RHDE8000 Bedienungsanleitung
ABB
ABB ControlMaster CM50 Bedienungsanleitung
ABB
ABB IRC5 Compact Bedienungsanleitung
ABB
ABB MS116 Bedienungsanleitung
ABB
ABB COMMANDER 360 Bedienungsanleitung
ABB
ABB DCS800-EP Installations- und Betriebshandbuch
ABB
ABB i-bus KNX ABA/S 1.2.1 Bedienungsanleitung
ABB
ABB Welcome M2300 Bedienungsanleitung
ABB
ABB MS165 Bedienungsanleitung
ABB
ABB ES/S 4.1.2.1 Bedienungsanleitung
ABB
ABB Relion 620 Series Bedienungsanleitung
ABB
ABB ACS800-U4 Bedienungsanleitung
