ABB i-bus BDB/S 1.1 Bedienungsanleitung
Product Manual ABB i-bus
®
EIB / KNX
Data Logging Unit
BDB/S 1.1
Intelligent Installation Systems
ABB
This manual describes the function of the Data Logging Unit BDB/S 1.1.
Subject to changes and errors excepted.
Exclusion of liability:
Despite checking that the contents of this document match the hardware and software,
deviations cannot be completely excluded.
We therefore cannot accept any liability for this. Any necessary corrections will be inserted in
new versions of the manual.
Please inform us of any suggested improvements.
BDB/S, Data Logging Unit
© 2006 ABB STOTZ-KONTAKT GmbH 3
ABB i-bus®EIB / KNX
Contents Page
1General 4
1.1 Product and functional overview...........................................................5
2Device technology 6
2.1 Technical data.......................................................................................6
2.2 Circuit diagram......................................................................................7
2.3 Dimension drawing...............................................................................8
2.4 Assembly and installation.....................................................................9
3Commissioning 11
3.1 Overview.............................................................................................11
3.2 Parameters .........................................................................................12
3.2.1 “General” parameter window............................................................12
3.2.2 Parameter window “Channel designator”.........................................16
3.2.3 Channel parameter settings “Individual for each channel” ..............17
3.2.3.1 Parameter window “Channel parameters page 1 of 2”..................17
3.2.3.2 Parameter window “Channel parameters page 2 of 2”..................24
3.2.4 Channel parameter settings “Same for all channels”.......................27
3.2.4.1 Parameter window “Channel parameters page 1 of 2”..................27
3.2.4.2 Parameter window “Channel parameters page 2 of 2”..................28
3.3 Communication object........................................................................29
3.3.1 Channel 1.........................................................................................29
3.3.2 Channel 2…35 .................................................................................31
3.3.3 General.............................................................................................32
4Planning and application 34
4.1 Application fields.................................................................................34
4.1.1 Application 1.....................................................................................34
4.1.2 Application 2.....................................................................................34
4.1.3 Application 3.....................................................................................34
4.1.4 Application 4.....................................................................................34
4.2 Reaction on bus voltage failure ..........................................................35
4.3 Reaction on bus voltage recovery ......................................................35
Appendix VII
A.1 Scope of delivery............................................................................... VII
A.2 Directory of drawings........................................................................ VIII
A.3 Directory of tables............................................................................... IX
A.4 Index.................................................................................................... X
A.5 Ordering information............................................................................ X
A.6 Notes.................................................................................................. XII
General
© 2006 ABB STOTZ-KONTAKT GmbH 4
ABB i-bus®EIB / KNX
1 General
The Data Logging Unit BDB/S 1.1 is an EIB / KNX device for logging
operational data (in hours) and counting operations on up to 35 channels.
Limit values are defined for the individual counter values which automatically
initiate an alarm message on the ABB i-bus®if they are exceeded.
Data logging can be used for example, to co-ordinate the maintenance
expenditure and to determine the operational life of different devices.
Possible applications for use of the BDB/S 1.1 can be found for example in
the fields of lighting, ventilation, pumps as well as transport systems.
This manual provides you with detailed technical information relating to the
Data Logging Unit BDB/S 1.1 installation and programming, and explains the
use of the device using examples.
This manual is divided into the following sections:
•Chapter 1 General
•Chapter 2 Device technology
•Chapter 3 Commissioning
•Chapter 4 Planning and application
•Appendix
General
© 2006 ABB STOTZ-KONTAKT GmbH 5
ABB i-bus®EIB / KNX
1.1 Product and functional
overview
The Data Logging Unit BDB/S 1.1 is a modular installation device for fast
installation in the distribution board with a module width of 2 space units.
The Data Logging Unit enables you to count the switching operations of
switch actuator channels in an ABB i-bus®system. Furthermore, the
operating hours of the connected loads can be recorded with a resolution of
up to one second. 35 independent channels are available each with seven
communication objects provided. The switching operations as well as the
operating hours can be recorded on a channel basis, where the counting
method from zero upwards or from a set value downwards can be selected.
The operating data of every channel is derived from the state of the
communication object Channel X switch position – received.
Via a communication object or parameter it is possible to define the
corresponding start or limit value for each individual switch operation counter
value. With a total value mode of counting, i.e. counting from zero up to a set
limit value, an alarm message is generated if the limit value is exceeded.
With a remaining value mode of counting, i.e. counting from an adjustable
start value down to zero, an alarm message is generated if zero is reached.
Via a communication object or parameter it is possible to define the
corresponding start or limit value for each individual operating hours counter
value. With a total run time mode of counting, i.e. counting from zero up to
set limit value, an alarm message is generated if the limit value is exceeded.
With a remaining run time mode of counting, i.e. counting from adjustable
start value down to zero, an alarm message is generated if the zero is
reached.
The counter values and start or limit values can be changed via the bus.
The values can only be modified after enabling via a communication object.
Via the communications object “Delete all operating data - System” all
operating data can be deleted in the Data Logging Unit.
Every state change adjustable via parameters increments the current
counter value of the operations counter by one.
The level to count the operating hours can be defined via a parameter.
The Data Logging Unit can even be set to count permanently via the level
setting. Counting is undertaken every second.
During a new start the switching states of the monitored switch actuator
channels are read after a settable time. A pause can be programmed
between the two corresponding telegrams. If a switch actuator does not
respond, the telegram will be repeated twice.
On bus voltage failure all counter values and start or limit values are saved
in BDB/S 1.1 and restored when the bus voltage recovers. If the limit values
are exceeded the Data Logging Unit sends the respective alarm messages
on the ABB i-bus®.
Device technology
© 2006 ABB STOTZ-KONTAKT GmbH 6
ABB i-bus®EIB / KNX
2 Device technology
For installation in the distribution board. The device is used for recording of
switching operations and operating hours on 35 channels. The BDB/S 1.1 is
operational after of the bus voltage. The module is programmed directly via
the application program ETS. The connection to the ABB i-bus®is
established via the bus connection terminal at the front of the device.
Fig. 1: BDB/S 1.1
2.1 Technical data
Power supply - Bus voltage 21 … 32V DC
- Current consumption, bus < 12 mA
- Leakage loss, bus Max. 250 mW
Connections - EIB / KNX via bus connection terminals
Operating and display elements - Programming LED for assignment of the physical address
- Programming button for assignment of the physical address
Enclosure - IP 20 to DIN EN 60 529
Safety class - II to DIN EN 61 140
Isolation category Overvoltage category III to DIN EN 60 664-1
Pollution degree 2 to DIN EN 60 664-1
EIB / KNX safety extra low voltage SELV 24 V DC
Temperature range - Operation
- Storage
- Transport
-5° C…+ 45° C
-25°C…+ 55°C
-25°C…+ 70°C
Ambient conditions - Maximum air humidity 93%, no condensation allowed
Design - Modular installation device (MDRC) Modular installation device, ProM
- Dimensions 90 x 36 x 64.5 mm (H x W x D)
- Mounting width in space units 2 (2 modules at 18 mm)
- Mounting depth 64.5 mm
Installation - On 35 mm mounting rail to DIN EN 60 715
Mounting position - as required
Weight – 0.1 kg
Housing/colour - Plastic housing, grey
Approvals - EIB / KNX to EN 50 090-1, -2 Certification
CE mark - in accordance with the EMC guideline and
- low voltage guideline
Table 1: Technical data
2CDC 071 247 F0006
Device technology
© 2006 ABB STOTZ-KONTAKT GmbH 7
ABB i-bus®EIB / KNX
Application program Max. number of
communication objects Max. number of
group addresses Max. number of
associations
Operating data recording/1 250 254 255
Table 2: Application program
Note: ETS is required for programming. If ETS3 is used a “.VD3” type
file must be imported. The application program is available in
the ETS under ABB/Safety and Monitoring/Controller.
2.2 Circuit diagram
2CDC 072 053 F0006
Fig. 2: Circuit diagram
1 Label carrier
2 Programming button
3 Programming LED
4 Bus connection terminal
Device technology
© 2006 ABB STOTZ-KONTAKT GmbH 8
ABB i-bus®EIB / KNX
2.3 Dimension drawing
2CDC 072 051 F0006
Fig. 3: Dimension drawing
Device technology
© 2006 ABB STOTZ-KONTAKT GmbH 9
ABB i-bus®EIB / KNX
2.4 Assembly and installation
The Data Logging Unit is a modular installation device for fast installation in
the distribution board on 35 mm mounting rails to DIN EN 60 715.
The connection to the bus is implemented using the supplied bus connection
terminal.
The device is ready for operation after connection to the bus voltage.
Accessibility of the devices for the purpose of operation, testing, visual
inspection, maintenance and repair must be must be provided (conform to
DIN VDE 0100-520).
Commissioning requirements
In order to commission the Data Logging Unit, a PC with ETS and a
connection to the ABB i-bus®, e.g. via a RS232 interface or a USB interface
is necessary.
The device is ready for operation after connection to the bus voltage.
The installation and commissioning may only be carried out by electrical
specialists. The appropriate norms, guidelines, regulations and
specifications should be observed when planning and setting up electrical
installations.
- The device should be protected from damp, dirt and damage during
transport, storage and operation.
- The device should not be operated outside the specified technical data!
- The device should only be operated in a closed housing
(distribution board)!
Device technology
© 2006 ABB STOTZ-KONTAKT GmbH 10
ABB i-bus®EIB / KNX
Supplied state
The Data Logging Unit is supplied with the physical address 15.15.255.
The application program is pre-installed. Hence, only group addresses and
parameters must be loaded during commissioning. The entire application
can be reloaded as required. A longer downtime may result if the application
program is changed or after a discharge.
Assignment of the physical address
The assignment and programming of the physical address is carried out
in the ETS.
Cleaning
If devices become dirty, they can be cleaned using a dry cloth. Should a dry
cloth not remove the dirt, they can be cleaned using a slightly damp cloth
and soap solution. Corrosive materials or solutions should never be used.
Maintenance
The device is maintenance-free. No repairs should be carried out by
unauthorised personnel if damage occurs (e.g. during transport or storage).
The warranty expires if the device is opened.
Inhaltsverzeichnis
Andere ABB Datenlogger Handbücher
