ABB M2004 Gebrauchsanweisung

System Settings

Welding Robot Station

M2004, IRC5

3HEA 802352-001 Rev. A

The information in this document is subject to alteration without prior notice and should not be regarded

as an undertaking from ABB Automation Technologies AB. ABB Automation Technologies AB assumes

no responsibility for errors that may occur in this document.

ABB Automation Technologies AB bears no responsibility for damage that is a consequence of using this

document or the software or hardware described in this document.

The document, or parts of it, may not be reproduced or copied without prior permission from ABB Auto-

mation Technologies AB. It may neither be imparted to a third party nor otherwise be used without autho-

rization. Infringement hereof will be subject to action in accordance with applicable laws.

Further copies of this document can be obtained from ABB Automation Technologies AB at current prices.

ABB Automation Technologies AB

Robotics

SE-72168 Västerås

Sweden

3HEA 802352-001 Rev. A i

Contents

System Settings

M2004, IRC5 1 Safety instructions 3

1.1 Description 3

1.2 Warning symbols (signals) 4

1.2.1 DANGER – Ensure that the main power switch is turned off. 5

1.2.2 WARNING – The unit is sensitive to ESD. 6

2 Calibrating the robot and the additional axes 7

2.1 Updating the revolution counter 7

2.2 Manual setting of the calibration values 9

2.3 Recalibrating the axes 12

2.3.1 Positioners of the types A, L and MTC 12

3 Definition of the tool data (tload) 15

3.1 Definition of the tool data (tload) 15

3.1.1 Welding gun with swan neck: 15

3.2 Setup welding gun without BullsEye® 16

4 Speed data for external axes 17

5 Drivers 19

5.1 Introduction 19

5.1.1 General 19

5.1.2 Parts handling 19

5.1.3 Advanced part 19

5.1.4 RAPID instructions 21

5.1.5 Safety position 23

5.2 Calibration of the station interchange unit for positioner IRBP26

5.2.1 Positioner IRBP with mechanical stop 26

5.2.2 Positioner IRBP without mechanical stop 29

5.3 Work positions 33

5.3.1 Introduction 33

5.3.2 Load position 33

5.3.3 Process position 36

5.3.4 Service position 38

6 Identification of load data for positioners IRBP 41

6.1 Load Identification for IRBP L /C 41

6.1.1 Parameters and movements 42

6.2 Load Identification for IRBP K 43

6.3 Load Identification for IRBP R 44

ii 3HEA 802352-001 Rev. A

6.4 Load Identification for IRBP A, B and D 45

7 Define payload for a mechanical unit 47

7.1 MechUnitLoad 47

7.2 Program execution 48

7.3 Limitations 50

7.4 Syntax 50

7.5 Related information 51

Safety instructions

3HEA 802352-001 Rev. A 3

1 Safety instructions

A robot is heavy and extremely powerful regardless of its speed. A stoppage or

longer stop can be followed by rapid, dangerous movements. Even if the robot's

pattern of movement is predetermined, an external signal can affect the movement

sequence, resulting in unanticipated movement.

It is therefore important that all safety instructions are observed when entering a

safety supervised area.

1.1 Description

Safety instructions can be found under tab 1 in the AW system manual for all steps

that involve risk for personal injury or material damage. In addition, they are

included in the instructions for each step.

General warnings, where the intention is to avoid problems, are only included in the

pertinent instructions.

Reference document

All personnel working with the welding robot system must have full understanding of the

applicable safety instructions.

Document Described in:

Related safety instructions. AW System manual, chapter introduction and safety

Safety instructions

Warning symbols (signals)

43HEA 802352-001 Rev. A

1.2 Warning symbols (signals)

Symbol

explanations The different types of warnings are set out in the following chapters according to the

table below:

The safety information in the document must not be interpreted as a guarantee from

ABB that the equipment cannot cause accidents or injury, even if all the safety

instructions have been observed.

Symbol Name Meaning

Danger Warning that serious or life-threatening personal injury and/or

serious damage to the product will occur if the instructions are

not followed.

Warning Warns of the risk of personal injury or serious damage to the

product. Always follow the instructions that accompany this

symbol.

Electric shock Warns of possible electric shock that can cause life-threatening

or serious personal injury. Always follow the instructions that

accompany this symbol.

Caution Draws your attention to the fact that damage to the product may

occur if an action is not performed or is performed incorrectly.

Static

electricity ESD The ESD symbol indicates a risk of static electricity that may

cause serious damage to the product.

Note Information about important parts.

Tips Thissymbolreferstoaninstructionprovidingfurtherinformation

on a particular step.

Safety instructions

DANGER – Ensure that the main power switch is turned off.

3HEA 802352-001 Rev. A 5

1.2.1 DANGER – Ensure that the main power switch is turned off.

Description

Work with high voltage entails a potential lethal hazard. Persons subjected to high

voltages can suffer heart failure, burns or other serious injuries. To avoid such

injuries, never begin a job without first eliminating the risks to safety. These are

descried below.

Elimination

Action Info/Illustration

1. Turnoffthemainpowerswitchatthe

control module.

The main power switch on the

control module switches off the

control voltage to all the drive

modules.

2. Turnoffthemainpowerswitch(work

switch) on the respective drive

module to switch off the feed

voltage.

3. Single robot stations All voltage is lost when the main switch on

the drive module (DM1) is switched off.

Safety instructions

WARNING – The unit is sensitive to ESD.

63HEA 802352-001 Rev. A

1.2.2 WARNING – The unit is sensitive to ESD.

Description

ESD (electrostatic discharge) is the transfer of electrostatic charges between two

objects with varying charges, either through direct contact or through an electrical

field.

The discharge contains very little electricity and is therefore not hazardous to

humans, however, electronics can be damaged by the high voltages.

Elimination

Location of attachment point for ESD bracelet

Button (A/B) for the ESD bracelet is located on the computer unit in the control

module/drive module. The location is shown in the following figure.

Action Info/Illustration

1. Use an ESD bracelet. The bracelet must be regularly tested to

ensure that it is undamaged and functions

properly.

2. Use an ESD-protected floor mat. The mat must be grounded through a voltage

regulating resistor.

3. Use an ESD-protected table mat. The mat shallproduce a controlled discharge

of static electricity and must be grounded.

xx0400001061

Figure 1 Location of attachment point for ESD bracelet

Item Name

A Attachment point for ESD bracelet in the control module.

B Attachment point for ESD bracelet in the drive module.

Calibrating the robot and the additional axes

Updating the revolution counter

3HEA 802352-001 Rev. A 7

2 Calibrating the robot and the additional axes

Thischapterdescribeshow you update the revolution counter, make manual settings

for calibration values and recalibrate the axes.

2.1 Updating the revolution counter

This measure is necessary when you have entered the calibration values manually

or for some reason need to update one or more of the axes' revolution counters

(resolver) against the synchronization position.

Usually the programmed positions are not affected by an update. If this happens the

entered values may be incorrect or the axis has been updated before programming

at an incorrect position i.e. not by the synchronization markings.

Action Info/Illustration

1. Move the robot's and positioner's axes to their respective zero positions (synchroni-

zation marking).

2. Tap ABB, to open the service window.

3. Tap Calibration.

4. Tap on the mechanical unit to be cali-

brated.

When the unit concerned is not

visible in the window, use the scroll

bar arrows, in the lower part of the

window.

(

Calibrating the robot and the additional axes

Updating the revolution counter

83HEA 802352-001 Rev. A

5. Tap Revolution Counters.

6. Tap Update Rev. Counters.

7. The system awaits a response:

• Tap YES if you want to proceed.

8. Select, by tapping, the axes to be

updated.

• Tap Select All to include all the

mechanical unit’s axes.

9. Tap Update.

Action Info/Illustration

(

Andere Handbücher für M2004

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ABB Robotik Handbücher

ABB

ABB IRB 1520 Leitfaden

ABB

ABB IRB 6640 Foundry Prime Bedienungsanleitung

ABB

ABB IRB 1600 - 5/1,2 type A Bedienungsanleitung

ABB

ABB IRB 1200 Bedienungsanleitung

ABB

ABB IRB 760 Betriebsanleitung

ABB

ABB IRB 6650S Series Bedienungsanleitung

ABB

ABB IRB 7600 Series Bedienungsanleitung

ABB

ABB Scalable I/O Gebrauchsanweisung

ABB

ABB OmniCore C90XT Bedienungsanleitung

ABB

ABB IRB 920 Bedienungsanleitung

ABB

ABB FlexLoader Gebrauchsanweisung

ABB

ABB IRB 4600 - 40/2.55 Bedienungsanleitung

ABB

ABB OmniCore C30 Bedienungsanleitung

ABB

ABB CRB 15000 Technisches Datenblatt

ABB

ABB M98 Produkthandbuch

ABB

ABB IRB 2400/L Bedienungsanleitung

ABB

ABB IRB 4400 - 45 Bedienungsanleitung

ABB

ABB IRB 1010 Bedienungsanleitung

ABB

ABB CRB 15000 Bedienungsanleitung

ABB

ABB IRB 6700 Series Bedienungsanleitung

ABB

ABB OmniCore Bedienungsanleitung

ABB

ABB Feather Duster Bedienungsanleitung

ABB

ABB IRB 6660 Bedienungsanleitung

ABB

ABB IRB 910INV Betriebsanleitung

Beliebte Robotik Handbücher anderer Marken

STEMCenter USA

STEMCenter USA Pi-Bot v2.00 Bedienungsanleitung

SunFounder

SunFounder PiDog Bedienungsanleitung

Universal Robots

Universal Robots UR5 Bedienungsanleitung

Universal Robots

Universal Robots E Series Bedienungsanleitung

YASKAWA

YASKAWA MOTOMAN-MPL80 II Bedienungsanleitung

EFORT

EFORT ECR5 Gebrauchsanweisung

Epson

Epson C8 Series Bedienungsanleitung

WowWee

WowWee ROBOQUAD Bedienungsanleitung

Milvus Robotics

Milvus Robotics SEIT 100 Bedienungsanleitung

RoboMaster

RoboMaster AI Robot 2020 Standard Version Bedienungsanleitung

fischertechnik

fischertechnik Mini Bots Bedienungsanleitung

YASKAWA

YASKAWA MA2010 Handbuch

Abicor Binzel

Abicor Binzel iCAT mini Bedienungsanleitung

YASKAWA

YASKAWA Motoman DX200 Bedienungsanleitung

pitsco

pitsco Tetrix Max Bedienungsanleitung

ECOVACS

ECOVACS DEEBOT R95 Bedienungsanleitung

Feng Yuan

Feng Yuan Interstellar Warrior Bedienungsanleitung

SCHUNK

SCHUNK AGE-S-XYZ Gebrauchsanweisung