ABB OTM C 21D Bedienungsanleitung

—

INSTALLATION AND OPERATING INSTRUCTION

Automatic Transfer Switch

OTM_C_21D

—

Automatic Transfer switch

34OTM_C_21D rev. E / 1SCC303015M0201 / EN

2AUTOMATIC TRANSFER SWITCH, OTM_C_21D

—

Table of contents

1. SYMBOLS & TERMS 3

2. PRODUCT OVERVIEW 4

3. QUICK START 78

4. INTERFACE AND SETTINGS 17

5. TECHNICAL DATA 22

6. INSTALLATION 23

7. OPTIONAL ACCESSORIES 26

8. MAINTENANCE AND COMMON

TROUBLESHOOTING 29

9. APPENDIX 30

AUTOMATIC TRANSFER SWITCH, OTM_C_21D

—

1. Symbols & Terms

—

1.1 Use of symbols

Risk of Electric shock: warns about a situation where a hazardous voltage may cause phys-

ical injury to a person or damage to equipment.

General warning: warns about a situation where something other than electrical equip-

ment may cause physical injury to a person or damage to equipment.

Caution: provides important information or warns about a situation that may have a detri-

mental effect on equipment.

Information: provides important information about the equipment.

Table 1. Explanations of abbreviations and terms

—

1.2 Explanations of abreviations and terms

OTM_C21D Automatic transfer switch, the type name

LN1-Switch I Power supply line, e.g. the primary line

LN2-Switch II Power supply line, e.g. the secondary line used in emergency cases

EMRG OFF Used to drive the automatic transfer switch transfers to the “O” position when

receiving EMRG OFF signal.

AUTO Automatic mode

Remote test A sequence to test the functionality of the automatic transfer switch

Ts Transfer delay

TBs Return delay

OV Adjustable overvoltage threshold

UV Adjustable undervoltage threshold

4AUTOMATIC TRANSFER SWITCH, OTM_C_21D

The OTM_C21D automatic transfer switch can be

used as a source transfer switch in a three-phase

or single-phase networks. Monitored conditions

are, no-voltage, phase-loss, overvoltage and un-

dervoltage detection, transfer delays, generator

start and stop, and remote test function. Source

transfer can be performed using a manually

The standard package includes:

1. automatic transfer switch, 2. handle, 3. handle storage clip 4. terminal plug, 5. mounting kit

Figure 1. OTM_C_21D automatic transfer switch

1. Handle for manual operation

2. Place for auxiliary contact blocks

3. Push button

4. Mimic panel

5. Voltage sensing connections

6. Locking clip for padlock

7. Locking latch for releasing the handle and

locking electrical control

8. Locking clip for locking manual operation

9. Dip switches

10. Rotary switches

11. Connecting terminal

12. Modbus RTU access

10 4 5

8 1 3 6 2

operated handle, locally using push buttons or

fully automatically. The automatic mode includes

several operating methods: Line 1 priority, no line

priority and manual back switching mode. OTM_

C21D can achieve communication function by

using the optional external Modbus RTU module.

—

2. Product overview

—

2.1 Product overview and packing

AUTOMATIC TRANSFER SWITCH, OTM_C_21D

And the return sequence can be summarized in

the following steps:

•The Line 1 will start the normal functioning

•Return delay TBs

•Change-over switch (Switch II) to the position 0

•Change-over switch (Switch I) to the position I

•Generator stop delay Gs

•Generator stop

Figure 2. Automatic Switching Sequences in OTM_C_21D, Line 1 priority

The transfer sequence of OTM_C21D can be sum-

marized in following steps:

•An anomaly occurs on the Line 1 (LN1)

•Generator start, immediately start generator in

case of black-out, phase-loss, overvoltage or

undervoltage (If Generator mode is selected)

•The Line 2 start the normal functioning,

transfer delay Ts

•Change-over switch (Switch I) to the position 0

•Change-over switch (Switch II) to the position II

—

2.2 OTM_C21D switching sequence

2.2.1 Line 1 Priority (default mode)

6AUTOMATIC TRANSFER SWITCH, OTM_C_21D

The transfer sequence of OTM_C21D can be sum-

marized in following steps:

•An anomaly occurs on the Line 1 (LN1)

•Transfer delay Ts, in case of black-out, phase-

loss, overvoltage and undervoltage conditions

•Change-over switch (Switch I) to the position 0

•Change-over switch (Switch II) to the position II

And the return sequence can be summarized in

the following steps:

•The Line 1 will start the normal functioning

•Change-over switch stays in position II

•An anomaly occurs on the Line 2 (LN2)

•Return delay TBs

•Change-over switch (Switch II) to the

position 0

•Change-over switch (Switch I) to the position I

Figure 3. Automatic Switching Sequences in OTM_C_21D, No line priority

Generator can not be used in no line priority. Keep Dip switch “GEN SEL” setting “0”

in this mode.

2.2.2 No line priority

AUTOMATIC TRANSFER SWITCH, OTM_C_21D

The transfer sequence of OTM_C21D can be sum-

marized in following steps:

•An anomaly occurs on the Line 1 (LN1)

•Generator start, immediately start generator

in case of black-out, phase-loss, overvoltage or

undervoltage (If Generator mode is selected)

•The Line 2 start the normal functioning,

transfer delay Ts

•Change-over switch (Switch I) to the position 0

•Change-over switch (Switch II) to the

position II

Figure 4. Automatic Switching Sequences in OTM_C_21D, Manual return mode

And the return sequence can be summarized in

the following steps:

•The Line 1 will start the normal functioning

•Change-over switch stays in position II

•An anomaly occurs on the Line 2 (LN2)

•Change-over switch stays in position II

•Change-over switch can be transferred

manually back to position I

2.2.3 Manual return mode

8AUTOMATIC TRANSFER SWITCH, OTM_C_21D

To operate the switch manually:

1.Attach the handle to the switch panel. You can

attach the handle in any position.

2.When the handle is attached, the automatic

transfer switch will automatically be in Manual

mode and won’t operate automatically in case

of line failure. The AUTO LED on the mimic panel

is OFF.

Figure 5. Operating the switch manually

When the handle is inserted into the switch, the switch will enter “manual mode” with the

automatic operation disabled.

Do not adjust wires when the transfer switch is being energized.

Before the power-on operation of the transfer switch, please operate the switch manually

to confirm it is in normal function.

With the power supply function in “normal” and without the handle inserted and EMRG OFF

signals, the initially energized switch will enter automatic mode and transfer to the main

line. Keep the handle inserted if you do not want the switch to be in automatic mode upon

initial energization.

—

3. Quick start

—

3.1 Operating the switch manually (local operation)

AUTOMATIC TRANSFER SWITCH, OTM_C_21D

OTM_C21D must be in automatic mode and the

“AUTO” LED is on in order that the switch can

perform automatic transfer cycles according to

the pre-set operating mode.

To operate the switch electrically:

•If the handle inserted

1. Press handle locking clip and remove the handle

from the switch.

2. Press “AUTO” button and the “AUTO” LED will

be ON, indicating automatic mode.

Figure 6. Selecting the automatic transfer OTM_C_21D, switch to Auto Mode

—

3.2 Automatic operation

•If handle is not inserted

1. If “AUTO” LED blinks, press “AUTO” button and

the “AUTO” LED will be ON, indicating auto-

matic mode.

2. Automatic operation includes three operating

modes: Line 1 priority (factory default setting),

No line priority, and manual return mode.

10 AUTOMATIC TRANSFER SWITCH, OTM_C_21D

Figure 7. Remote test connection in OTM_C_21D

In the test sequence, the main power supply circuit will be closed.

If the test sequence is interrupted due to power failure, the automatic transfer switch will

enter “automatic mode” after power recovery.

In automatic mode, “AUTO” LED is ON and you can

transfer the switch using I, O, and II push buttons

on the front panel of the switch.

Press “AUTO” button to return the automatic

operation.

—

3.3 System testing

3.3.1 Local test

The procedure of the remote test is as follows:

1. Connect to the remote test signal according to

Figure 7.

2. Ensure that the OTM_C21D is in automatic

mode (“AUTO” LED is on).

3. Short circuit the remote test signal for at least

100 ms until the “AUTO” LED blinks to enter the

test mode. Under test mode, the automatic

transfer switch will simulate switching cycle

and finally return to its original position prior

to the activation of the test mode.

e.g., when the switch is in Position I:

Enter test signals; the switch transfers to

 

Position I. Entering test signals is invalid before

the automatic transfer switch returns to its

original position.

Under test mode, press the “AUTO” button to

cancel test mode and return to automatic

mode. The “Auto” LED will be “ON” as normal.

4. After the remote test finishes, the OTM_C21D

automatically returns to the automatic mode

(“AUTO” LED is on).

3.3.2 Remote test

Andere Handbücher für OTM C 21D

Inhaltsverzeichnis

Andere ABB Schalten Handbücher

ABB

ABB MS40/EX Bedienungsanleitung

ABB

ABB OTM_C Series Benutzerhandbuch

ABB

ABB ITS2.1 Bedienungsanleitung

ABB

ABB DY365 Series Bedienungsanleitung

ABB

ABB E 232 E-230N Bedienungsanleitung

ABB

ABB NAL Series Bedienungsanleitung

ABB

ABB FIP2002 Bedienungsanleitung

ABB

ABB E232-230 Bedienungsanleitung

ABB

ABB SACE Tmax XT Bedienungsanleitung

ABB

ABB MKey8M Bedienungsanleitung

ABB

ABB SACE Emax Leitfaden

ABB

ABB TruONE ATS OXB250E3S3QT Bedienungsanleitung

ABB

ABB Sense7 Series Bedienungsanleitung

ABB

ABB TX series Bedienungsanleitung

ABB

ABB IS/S 8.1.1 Bedienungsanleitung

ABB

ABB 3299H-A02182 Leitfaden

ABB

ABB ESP630 A2 Bedienungsanleitung

ABB

ABB 8185.1 Bedienungsanleitung

ABB

ABB ZX1.5-R Bedienungsanleitung

ABB

ABB UniGear Series Bedienungsanleitung

ABB

ABB vital 1 Bedienungsanleitung

ABB

ABB FIP1011 Bedienungsanleitung

ABB

ABB ATS021 Bedienungsanleitung

ABB

ABB Zenith ZTG T Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung