Functions and settings
NOTE: You can only change the settings when there is no active
timer.
= Simultaneously push and hold down the indicated time buttons.
The default settings are indicated in bold italic.
Function Buttons Information
Start timer
Press and release
the time button that
corresponds to the
requested time
interval.
The corresponding number of
dots light up.
The indicator on the selected
button lights up (if setting =
’Button lights on’).
When time is out, the alarm
sets off with a flashing time
pillar and with signal and
vibration according to
settings.
Stop alarm Press and release
any button. The alarm is stopped.
Cancel
countdown + 2 sec The countdown is interrupted.
Adjust
alarm
volume
Press and release
Volume +/- to
increase and
decrease the alarm
volume.
Volume in five steps. 1=silent,
5=max (default setting=3).
A sample signal sounds at
each step.
A vibration announces step 1
and step 5.
The settings on this page cannot be changed when a timer is
ongoing.
Setting Buttons Information
Change
alarm
signal
+
2 sec
Use Volume
+/- to change.
A sample
signal sounds
at each step.
Alarm
1
Alarm
2
Alarm
3
Vibration +
2 sec
Use Volume
+/- to change. Off On
On in
silent
mode
Button
lights
+
2 sec
Use Volume
+/- to change. Off On
Max
brightness
+
2 sec
Brightness in five steps. 1=min, 5=max
(default setting = 3).
Use Volume +/- to change. The set
brightness is shown at each step.
Leave
setting
mode
+Illuminated dots flash 3 times.
Alternatively, wait for 10 seconds.
Keylock
+
( , , )
See info*
Locked = Time pillar flashes once. Only
”start timer” and ”stop alarm” possible.
Unlocked = Time pillar flashes twice.
Reset
+ +
+
2 sec
Reset to default settings.
* Push and hold down the blue button while sequentially pushing
and releasing the green, yellow and red buttons.
What's in the box
l1 x MEMO Timer
l1 x Neck strap
l1 x Short strap
l2 x AA batteries 1,5 V
lUser manual (this document)
Product specifications
Dimensions H x W x D: 107 x 46 x 25 mm
Weight: 0.12 kg
Battery: 2 x AA 1,5 V
Alarm volume: max 80 dB (1 meter)
IP code: IP67
Temperature range: -10°C to +40°C
Storage and disposal
Remove the batteries before storing the product for a long period.
The product contains electrical components that must
be recycled. Dispose the product at an applicable
disposal location.
Conformance with requirements for medical devices
MEMO Timer is marketed as a technical aid for people with
disabilities. It complies with all necessary requirements, regulations
and directives for medical devices.
Important information
WARNING: Read the following warning instructions before
you use the product.
lBefore you use the product, read and understand the contents
of this user manual.
lOnly use the provided straps with security buckle to avoid
choking and other injuries.
Serious incidents
If a serious incident related to the product occurs, report this to the
manufacturer and the competent authority of your country. A
serious incident directly or indirectly led, might have led or might
lead to the death of a patient, user or other person; the temporary or
permanent serious deterioration of a patient's, user's or other
person's state of health; or a serious public health threat.
Product liability
The product is developed and risk-assessed according to ISO
14971 and EN 12182. The manual and the technical specifications
are made according to the safety assessments in the risk analysis.
Always consider the safety when using the product. Abilia AB does
not take responsibility for any consequences following incorrect use
or installation of the product. Any form of damage or tampering with
the product invalidates the warranty and disclaims the
manufacturer's liability. The estimated life of the product applies
when used in accordance with its intended use and maintenance
instructions.
For more information about the product and the latest version of this
document, go to www.abilia.com/en.
