Abit BP6 Bedienungsanleitung

The information in this document is subject to change without notice and does not

represent a commitment on part of the vendor, who assumes no liability or

responsibility for any errors that may appear in this manual.

No warranty or representation, either expressed or implied, is made with respect to

the quality, accuracy or fitness for any particular part of this document. In no event

shall the manufacturer be liable for direct, indirect, special, incidental or

consequential damages arising from any defect or error in this manual or product.

Product names appearing in this manual are for identification purpose only and

trademarks and product names or brand names appearing in this document are

property of their respective owners.

This document contains materials protected under International Copyright Laws. All

rights reserved. No part of this manual may be reproduced, transmitted or

transcribed without the expressed written permission of the manufacturer and

authors of this manual.

If you do not properly set the motherboard settings causing the motherboard to

malfunction or fail, we cannot guarantee any responsibility.

All brand names and trademarks shown in this manual are the property of their respective owners.

MN-159-2A1-21 Rev. 1.01

BP6 Motherboard User’s Manual

Table of Contents

CHAPTER 1 INTRODUCTION OF BP6 FEATURES 1-1

1-1.Features of This Motherboard 1-1

1-2. Specifications 1-2

1-3. Layout Diagram 1-5

1-4. The System Block Diagram 1-6

1-5. Dual Processor Knowledge You Should Know 1-7

CHAPTER 2 INSTALLING THE MOTHERBOARD 2-1

2-1. Installing the Motherboard to the Chassis 2-2

2-2. Installation of the Socket 370 processor 2-3

2-3. Installing System Memory 2-4

2-4. Connectors, Headers and Switches 2-6

CHAPTER 3 INTRODUCTION OF THE BIOS 3-1

3-1. CPU Setup [SOFT MENU™II] 3-3

3-2. Standard CMOS Setup Menu 3-8

3-3. BIOS Features Setup Menu 3-11

3-4. Chipset Features Setup Menu 3-17

3-5. Power Management Setup Menu 3-21

3-6. PNP/PCI Configuration 3-28

3-7. Load Setup Defaults 3-30

3-8. Integrated Peripherals 3-31

3-9. Password Setting 3-36

3-10. IDE Hard Disk Detection 3-37

3-11. Save & Exit Setup 3-38

3-12. Quit Without Saving 3-38

APPENDIX A BIOS FLASHING USER INSTRUCTIONS

APPENDIX B INSTALLING THE HIGHPOINT XSTORE PRO UTILITY

APPENDIX C HARDWARE MONITORING FUNCTION (INSTALLING

THE WINBOND HARDWARE DOCTOR UTILITY)

APPENDIX D INSTALLING THE DRIVER FOR ULTRA ATA/66

APPENDIX E TROUBLESHOOTING (NEED ASSISTANCE?)

Introduction of BP6 Features 1-1

User’s Manual

Chapter 1 Introduction of BP6 Features

1-1.Features of this Motherboard

This motherboard is a specialdesign forSocket 370 CPUs. It is equipped withtwo PGA 370

sockets with which you can install two Socket 370 processors.

The BP6 has the HPT366 Ultra ATA/66 Chipset built-in. This means, the BP6 will support

Ultra ATA/66 IDE devices. Ultra ATA/66 is the new standard for IDE devices. It enhances

existing Ultra ATA/33 technology by increasing both performance and data integrity. This

new high-speed interface doubles the Ultra ATA/33 burst data transfer rate to 66.6

Mbytes/sec. The result is the maximum disc performance using the current PCI local bus

environment. Another benefit is, you can connect another four IDE devices in your system

either Ultra ATA/33 IDE devices or Ultra ATA/66 IDE devices. You will have more

flexibility to expand your computer system.

The BP6 has built-in hardware monitoring functions (you can refer to Appendix C for

detailed information), they can monitor and protect your computer insuring a safe

computing environment. The BP6 also supports both the PS/2 keyboard and PS/2 mouse

wake up features (you can refer to section 3-8 for detailed information), letting you easily

wake up your system by these devices. The motherboard can provide high performance for

workstations and meets the requirements for desktop systems for multimedia in the future.

Sets You Free From the Y2K Threat

The potential threat of Year 2000 (Y2K) problems are making everyone very nervous. The

Y2K issue applies to almost any device, firmware, or software that operates on or with year

based dates. This problem is caused by a design flaw in the Real Time Clock (RTC) unit.

The RTC only changes the last two digits of the year code, but not the century information.

As a result, when it comes to 12:00 AM January 1, 2000 the RTC will switch from

December 31 11:59 PM 1999 to 12:00 AM January 1 1900.

Y2K compliance deals with the date change over from 31 December 1999 to 1 January 2000,

and with recording and reporting of all dates from the RTC including leap year dates. This

motherboard is free from the Y2K problem because its BIOS are Y2K compliant.

1-2 Chapter1

BP6

Please Note

If the operating system or application software cannot handle Year 2000 dates, you will

still be facing the Y2K threat because it is not a hardware problem that relates to the

motherboard itself. According to Award BIOS, it’s BIOS source code released after 31

May 1995 complies with all known Y2K issues; however, it may still fail the 2000.exe

test. Award has modified its BIOS source code to accommodate the requirements of

2000.exe. Award BIOS source code issued later than 18 November 1996 passes the

NTSL 2000.exe test program.

1-2. Specifications

1. CPU

!Supports Dual Socket 370 processors

!Supports Intel®Celeron™ 300A~466MHz processors (Based on 66MHz PPGA package)

2. Chipset

!Intel440BX (66/100MHz) AGPset

!HPT366 Ultra DMA/66 IDE controller supports Four Ultra DMA66 devices

!Supports Ultra DMA/33 IDE protocol

!Supports Advanced Configuration and Power Management Interface (ACPI)

!Supports AGP 1X/2X

3. Cache Memory

!Level 1 and Level 2 cache built into Intel®Celeron™processor (PPGA package)

4. Memory (System Memory)

!Three 168-pin DIMM sockets support SDRAM module

!Supports up to 768MB (8, 16, 32, 64, 128, 256MB SDRAM)

!ECC support

5. System BIOS

!CPU SOFT MENUTM II eliminates the need for jumpers or DIP switches needed to set

CPU parameters

!Award Plug and Play BIOS supports APM, DMI, and ACPI

!Write-Protect Anti-Virus function by AWARD BIOS

!Year 2000 Compliant

Introduction of BP6 Features 1-3

User’s Manual

6. Multi I/O Functions

!2x Channels of Bus Master IDE Ports supporting up to four Ultra DMA 33/66 devices

!2x Channels of Bus Master IDE Ports supporting up to four Ultra DMA 33 devices

!PS/2 Keyboard and PS/2 Mouse Connectors

!1x Floppy Port ( up to 2.88MB)

!1x Parallel Port (EPP/ECP)

!2x Serial Ports

!2x USB Connectors

7. Miscellaneous

!ATX form factor

!1 AGP slot, 5 PCI slots and 2 ISA slots

!Hardware monitoring – Included fan speed, voltages, System environment temperature

!Keyboard and PS/2 Mouse Power On

!Built-in Wake on LAN header

!Built-in IrDA TX/RX header

!Built-in SMBus connector

!Built-in Wake On Ring Header

!Board size: 305 ×240mm

1-4 Chapter1

BP6

"Supports Wake Up on LAN, Keyboard or Mouse, but your ATX power supply 5V

standby (5VSB) power must be able to provide at least a 720mA current capacity.

Otherwise, the functions may not work normally.

"PCI slots 4 and 5 use the same bus master control signal.

"PCI slot 3 shares IRQ signals with the HPT366 IDE controller (Ultra ATA/66). The

driver for the HPT 366 IDE controller supports IRQ sharing with other PCI

devices. But if you install a PCI card that doesn’t allow IRQ sharing with other

devices into PCI slot 3, you may encounter some problems. Furthermore, if your

Operating System doesn’t allow peripheral devices to share IRQ signals with each

other--Windows NT for example, you can’t install a PCI card into PCI slot 3.

"HPT 366 IDE controller is designed to support high-speed mass storage. Thus we

don’t suggest you connect non-disk devices that use ATA/ATAPI interfaces, such as

CD-ROM to HPT 366 IDE connector (IDE3&IDE4).

#Sound Blaster™is a registered trademark of Creative Technology Ltd. in the United

States and certain other countries. Sound Blaster-LINK™and SB-LINK™ are trademarks

of Creative Technology Ltd.

#Specifications and information contained in this manual are subject to change without

notice.

#All brand names and trademarks are the property of their respective owners.

Important Notice

Based on peripheral specifications and other considerations, the BP6 SMP (Symmetric

Multiple Processor) function is designed for testing only. The BP6 motherboard can’t

manage the SMP function alone. It must co-operate with the CPU and OS that support

the SMP function. Therefore, any damage caused by employing an improper or OS will

void the warranty.

Introduction of BP6 Features 1-5

User’s Manual

1-3. Layout Diagram

Figure 1-2. Motherboard component location

1-6 Chapter1

BP6

1-4. The System Block Diagram

Figure 1-3. The system diagram of BP6

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Abit Hauptplatine Handbücher

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung