Abode Pronteau PROBOIL2 Bedienungsanleitung

PROBOIL 2 to

PROBOIL

.2X Upgrade Installation Guide

PROBOIL2 to PROBOIL.2X

Upgrade Installation Guide

www.proboil.co.uk

See top of boiler unit for contact details

 Please read these instructions carefull before installation

We have a polic of continued product and qualit development and improvement.

Accordingl , we reserve the right to amend the specification at an time. All errors and omissions excepted.

PROBOIL 2 to

PROBOIL

.2X Upgrade Installation Guide

Thank you for choosing PROBOIL.2 . By reading this entire guide you will ensure that the product is installed and used

safely and will give its best performance, this guide should be used in conjunction with any additional product guides.

1 PROBOIL.2X user guide

PROBOIL.2X user guidePROBOIL.2X user guide

PROBOIL.2X user guide

1.1

1.11.1

1.1 Important safet and usage considerations

Important safet and usage considerationsImportant safet and usage considerations

Important safet and usage considerations:

Throughout this guide, the following symbols are used to highlight key points or safety considerations.



An information point or tip for

installation or usage.



A service, maintenance

or care consideration.

⚠

A technical or safety

consideration or warning of

hazardous situation with regard to

life and property.

1.1.1 General safet

⚠

WARNING

this guide is intended solely as explanation for the method to exchange proboil2x

boilers like for like, if any modifications are to be made please refer to the complete user and installer

guide supplied originally with the product.

⚠

WARNING

All surfaces, especially those made from metal, may become hot whilst in operation.

Use caution when touching these surfaces. Inform all users that the surfaces may become hot.

⚠

WARNING

Do not disconnect the tank until the tank has cooled to a safe temperature.

⚠ WARNING

This appliance must be installed respecting local plumbing and electrical regulations.

⚠ WARNING

This appliance must use only genuine parts and accessories and sundry

consumables.

⚠ WARNING

Packaging materials can be dangerous to children and animals; ensure they are

disposed of safely and correctly according to local laws.

1.1.2 Electrical safet :

⚠ WARNING

Do not use this appliance if you suspect it or any of its cables or hoses are damaged

or kinked in any way, or is performing differently from how you would expect. Never use any

appliance with a damaged mains power lead. In the event of any suspected problem you should

immediately cease usage, isolate the water supply, disconnect the power and contact the service

agent noted on the top of the boiler.

PROBOIL 2 to

PROBOIL

.2X Upgrade Installation Guide

⚠ WARNING

This appliance must be disconnected from the power during installation,

maintenance or cleaning.

⚠ WARNING

Only use the supplied power cable and connect it directly to the power outlet rather

than an extension power outlet.

⚠ WARNING

The appliance must be installed so that it can be disconnected from the mains

power supply and the outlet socket must be accessible at all time.

⚠ WARNING

This appliance must be connected to a grounded / earthed power outlet only.

⚠ WARNING

This appliance must be installed respecting local plumbing and electrical regulations.

⚠ WARNING

Do not place any water connections directly near or above electrical appliances or

connections.

⚠ WARNING

This appliance is not intended to be operated by means of an external time or

separate remote control system.

1.1.3 Intended purpose:

⚠

This appliance is intended only for domestic use and should not be used for commercial

purposes.

⚠

Do not add to, exchange or modify any component of the boiler, mixer tap, filter or connections

from those supplied and install them only as instructed. The spout exit or any part of the system must

not include any additional third party adaptors or connections that will add resistance to the system.

⚠

This appliance is intended to be permanently connected to the water mains.

⚠

The boiler and mixer tap are not designed to work with any other combination of appliances

other than as shown within this guide.

PROBOIL 2 to

PROBOIL

.2X Upgrade Installation Guide

1.1.4 Sensible fire safet precautions:

⚠

Do not store or use petrol or other flammable rags, paper, aerosols, vapours or liquids in the

vicinity of this or any other appliance.

⚠

Install the unit on a heat-resistant surface. Make sure that the installation surface is firm and

level.

⚠

For safety regulations the plug or means of disconnection must always be accessible after

installation.

⚠

Do not use any water jet or steam near this appliance.

⚠

Always ensure an airgap of at least 10mm around the appliance and that any closed cabinet has

sufficient airflow.

2.1

2.12.1

2.1 Installation:

Installation:Installation:

Installation:

2.1.1 Installation preparation

Throughout this guide, the following symbols are used to highlight key points or safety considerations.



An information point or tip for

installation or usage.



A service, maintenance

or care consideration.

⚠

A technical or safety

consideration or warning of

hazardous situation with regard to

life and property.



Preparing yourself to install your replacement PROBOIL2X boiler is simple and ensures the process is

both quick and safe. The process is very similar to the descaling and cleaning maintenance process in your

user guide and requires no specialist tools or knowledge other than this guide.

⚠

Before installing your replacement boiler please unpack it and check for any missing parts or transport

damage, in case of an issue please contact the service number on top of the boiler.



Whilst installing your replacement boiler please check if the filter is also due to be replaced.



You might find it helpful to photograph the installation before your remove the old boiler as a

memory aid.

PROBOIL 2 to

PROBOIL

.2X Upgrade Installation Guide

This drawing of PROBOIL2 can be used for reference throughout the PROBOIL2X replacement process

Key

Description

Qty

Mixer tap 1

Base plinth 1

Base plinth seal 1

Sink or worktop (max. 50mm)

White triangular plate (for steel sinks onl ) 1

Lower gasket 1

Metal horseshoe 1

Fixing stud 1

Fixing nut 1

Domestic cold flexible hose (including non-

return valve)

15mm olive

15mm nut

15mm pipe

15mm isolation valve

Domestic hot flexible hose (excluding non-

return valve)

Cold out (to filter & boiler) flexible hose

(including seal)

3/8” M x ¼”F adaptor 1

¼” NPT M x ¼” pushfit 1

¼” outside diameter plastic pipe 1*

Filter bracket screw 1

Filter bracket 1

Filter cartridge 1

110° rated hot water hose (from boiler

output)

3/8” fibre seal 1

Boiler 1*

Flexible black rubber water output pipe 1*

Connecting tundish assembl 1*

Flexible drain pipe 1*

*Part supplied with boiler pack.

⚠ Do not switch on the boiler until instructed.

PROBOIL 2 to

PROBOIL

.2X Upgrade Installation Guide

2.1.2 Removing the existing PROBOIL2

PROBOIL2PROBOIL2

PROBOIL2 boiler:

Remove the boiler

Turn power off, take

the plug out.

Turn on

the

tap until water runs cold,

then fully turn off (approximately 3

litres).

Firmly pull up

black

rubber hose

(a)

press collar (c) down and pull pipe (b)

out simultaneously. Prepare for small

spillage.

Unhook boiler from

brackets (if mounted to

cabinet wall),

Open the drain on front of the unit.

Drain fully into a suitable container or

sink.

Once drained close the unit and place

the boiler to one side.

EITHER Bypass the existing Proboil 2 black tundish assembly (This is the preferred option)

Unscrew tundish

(E3) from hose (D1)

using spanners as

shown.

Connect hose (D1) to 8mm

barbed stem (L) ensuring

washer (D2) is in place.

Now connect outlet tube (K)

to 8mm barbed stem (L).

⚠

You must not connect

hose (D1) directly to the

male boiler outlet (C).

Pull black rubber

boiled water

outlet pipe (E2)

from tundish

(E3).

You can additionally

remove the tundish

assembly (E3 & E4) but the

dishwasher connection

MUST be blanked/capped

off (see above).

Dishwasher

connection

Blanking

Cap

PROBOIL 2 to

PROBOIL

.2X Upgrade Installation Guide

OR Continue to use the PROBOIL2 tundish and drain hose (Not preferred option)

Pull black rubber boiled water

outlet pipe (E2) from tundish (E3).

Push silicone outlet tube (K) onto stem of

tundish (E3).

2.1.3 Install the new PROBOIL2X

PROBOIL2XPROBOIL2X

PROBOIL2X replacement boiler

This drawing can be used for reference throughout the PROBOIL2X replacement process

Key

escription

Drawing

PROBOIL.2 boiler unit

½” male boiler inlet (with

internal check valve)

3/8” male boiler outlet

mains power cable

¼” flexible blue inlet pipe

¼”

x ¼”

inlet pushfit

connector

½”

blue

Inlet “wingnut”

connector (with integral

“flat” rubber seal)

inlet

connector

meshed

filter seal

Outlet

connector

rubber

seal

3/8”

red

Outlet “wingnut”

connector

ilicone outlet tube (0.75M)

8mm

barbed stem x 3/8”

male tap connector

2 x Wall fixing screws

2 x Wall fixing plugs

½” inlet transport cap

3/8” outlet transport cap

3/8” female flexible

(braided/silicone) hose tap

connector assembly and

fibre seal (supplied with

tap)

PROBOIL 2 to

PROBOIL

.2X Upgrade Installation Guide

Installing new PROBOIL2X boiler

⚠

WARNING

You must not solely use the overall assembly diagram as a guide to installation, we are not liable for

any safety or performance issues as a result of not following the step by step installation guide in this guide with due

care.

Insert the ½” rubber meshed seal

(H)

into the ½” boiler inlet

(B), ensure the orientation of the seal is as shown.

Screw the ½” blue wingnut inlet connector

with integral

internal “flat” rubber seal (G) hand tight (do not use a

spanner or overtighten) on to the boiler ½” inlet male (B).

Check that the red 3/8” x 8mm boiler outlet connector

(J)

has pre-inserted internally the 3/8” rubber seal (I), an

additional seal is supplied, ensure to use only 1 x 3/8”

rubber seal in this connection.

Screw the red 3/8” x 8mm boiler outlet connector

(J)

hand

tight (do not use a spanner or overtighten) on to the boiler

3/8” male outlet (C).

Plug the pow

er cable

)

securely into the socket on the

left

hand side of the boiler (A).

Hook the boiler keyhole slots onto its wall fixing screws

(M)

and check it is secure.

PROBOIL 2 to

PROBOIL

.2X Upgrade Installation Guide

Check the end of blue pipe

(E)

for signs of wear, if needed

cut the worn section of the end of the pipe using a sharp

Stanley knife or similar.

8) Push the ¼” blue flexible pipe (E) fully and firmly into the ¼”

x ¼” pushfit connector (F)

Firmly and fully push the silicone

rubber

outlet tube

(K)

over

the red boiler outlet (J).

The silicone outlet tube (K) must:

a) Not be excessively long, creating a “dead leg”.

b) Not be too short (pipe is stretched).

c) Not be twisted or kinked when attached (creating a

blockage).

10)

Your boiler is now plumbed to the tap and the filter, plug the power cord into the mains outlet

but do not

switch on the mains power outlet at this time.

11)

Now turn on (open) fully the 98°C water handle. Water will now begin to purge air though the entire s

ystem.



During the purging of air it is normal for the tap to spit, continue until the stream from the centre channel

of the tap aerator is continuous. Depending on the incoming water pressure it will take apx. 2-3 minutes to fill the

tank and purge the air.

12)

Now turn off (close) fully the 98°C water handle.

PROBOIL 2 to

PROBOIL

.2X Upgrade Installation Guide

2.1.4 Commissioning and testing

You have finished the installation, now please take a few moments to go through the commissioning and testing

process, this will ensure the product is working correctly, safely and to your satisfaction.

⚠ WARNING

You must not skip this section, we are not liable for any safety or performance issues as a result of

not following the step by step installation guide with due care.

Turn on (open) fully the 98°C water handle.

⚠

After the air is purged from the system you must continue to run cold water through the tank for a further

minimum of a 5 minutes to flush it.



During the flushing period check all connections made during the installation carefully for leaks.

After the flushing period is completed turn off (close) fully the 98°C water handle.

Press and hold the

“⏻ “

key

on the boiler screen, it should switch to the standard screen and not display any error

“E” codes.

Press the

“+”

key

on the boiler screen and set the target temperature to 98°C.

The boiler will take approximately 9 minutes to reach its “READY” state. Use this time to complete the checklist

items in this guide.



The few first times the boiler fills and heats from a “fully cold” state it is normal that the tap may drip

slightly from the spout centre channel during heating, this will self-adjust with use.

After the boiler reaches its

“READY”

state repeat steps 1

With all tap handles in the closed position again check

the installation carefully again for any leaks.

Inhaltsverzeichnis

Andere Abode Kessel Handbücher

Abode

Abode PROBOIL.2X Fehlerbehebungshandbuch

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung