Ace RGH100 Bedienungsanleitung

4Q Half-Wave SCR Chassis

Adjustable Speed Drive for PMDC Brush Motors

RGH100 / RGH200 14300 De La Tour Drive

South Beloit, IL 61080

Phone: (815) 624-6915

Fax: (815) 624-6965

www.americancontrolelectronics.com

REGENERATIVE

BRAKE SWITCH

(OPTIONAL)

Line Input Speed Potenometer

Connect the AC line power leads to terminals L1 and L2. ACE recommends the use of a double-pole, Use a 50K ohm, 1/4 W potenometer for speed control. Connect the counter-clockwise end of the

single throw master power switch. The switch should be rated at a minimum of 250 VAC and 200% of potenometer to S0, wiper to S2, and the clockwise end to S1. If the potenometer works

motor current. inversely of desired funconality, (i.e. to increase motor speed, you must turn the potenometer

counterclockwire), power oﬀ the drive and swap the S0 and S1 connecons. See the Operaon secon

Motor for alternave wiring setups.

Connect the DC armature leads to terminals A1 and A2. If the motor does not spin in the desired

direcon, power down the drive and reverse these connecons. Regenerave Brake

Short terminals S0 and RB to regeneravely brake the motor to zero speed. The me it takes the motor

to come a stop is dependent on load inera, fricon, and the FWD TQ and REV TQ trim pot sengs.

Open terminals S0 and RB to accelerate the motor to set speed.

Do not use the regenerave braking for emergency stopping.

LOGIC (TOP BOARD) POWER (BOTTOM BOARD)

Connections

FUSE

STOP

SWITCH

AC LINE

VOLTAGE

VAC

50K OHM

SPEED ADJUST

POTENTIOMETER

FUSE*

*NOTE: Do not add

fuse to L2 unless input

voltage is 230 VAC

Installation

Mounng

• Drive components are sensive to electrostac discharge. Avoid direct contact with the circuit

• board. Hold the drive by the chassis only.

• Protect the drive from dirt, moisture, and accidental contact.

• Provide suﬃcient room for access to the terminal block and calibraon trim pots.

• Mount the drive away from heat sources. Operate the drive within the speciﬁed ambient operang

• temperature range.

• Prevent loose connecons by avoiding excessive vibraon of the drive.

• Mount the drive with its board in either a horizontal or vercal plane. Six 0.19” (5 mm) wide slots

• in the chassis accept #8 pan head screws. Fasten either the large base or the narrow ﬂange of the

• chassis to the subplate.

• The chassis should be earth grounded. Use a star washer beneath the head of at least one of the

• mounng screws to penetrate the anodized chassis surface and to reach bare metal.

Wiring

Use 18 - 24 AWG wire for logic wiring.

Use 14 - 16 AWG wire for AC line (L1, L2) and motor (A1, A2) wiring.

Shielding Guidelines

As a general rule, ACE recommends shielding of all conductors. If it is not praccal to shield power

conductors, ACE recommends shielding all logic-level leads. If shielding of logic-level leads is not

praccal, the user should twist all logic leads with themselves to minimize induced noise. Refer to

the user’s manual for details on earth grounding shielded wires and ﬁltering.

Fusing

ACE drives require an external line fuse for protecon. Use fast acng fuses rated for 250 VAC or

higher and 150% of the maximum armature current. Fuse the HOT leg of the AC line when using 115

VAC and both lines when using 230 VAC.

ALL DIMENSIONS IN INCHES [MILLIMETERS]

Dimensions

Safety Warnings

• DO NOT INSTALL, REMOVE, OR REWIRE THIS EQUIPMENT WITH POWER APPLIED. Have a

• qualiﬁed electrical technician install, adjust and service this equipment. Follow the Naonal

•Electrical Code and all other applicable electrical and safety codes, including the provisions of the

• Occupaonal Safety and Health Act (OSHA), when installing equipment.

• Circuit potenals are at 115 above earth ground. Avoid direct contact with the printed circuit board

• or with circuit elements to prevent the risk of serious injury or fatality. Use a non-metallic

• screwdriver for adjusng the calibraon trim pots. Use approved personal protecon equipment

• and insulated tools if working on this drive with power applied.

• Reduce the chance of an electrical ﬁre, shock, or explosion by using proper grounding, over-current

• protecon, thermal protecon, and enclosure. Follow sound maintenance procedures.

• ACE strongly recommends the installaon of a master power switch in the line voltage input. The

•switch contacts should be rated for 250 VAC and 200% of motor nameplate current.

• Removing AC line power is the only acceptable method for emergency stopping. Do not use

• regenerave braking, decelerang to minimum speed, or coasng to a stop for emergency stopping.

• They may not stop a drive that is malfunconing. Removing AC line power is the only acceptable

•method for emergency stopping.

• Line starng and stopping (applying and removing AC line voltage) is recommended for infrequent

• starng and stopping of a drive only. Regenerave braking, decelerang to minimum speed, or

• coasng to a stop is recommended for frequent starts and stops. Frequent starng and stopping can

•produce high torque. This may cause damage to motors.

• Do not disconnect any of the motor leads from the drive unless power is removed or the drive is

• disabled. Opening any one lead while the drive is running may destroy the drive.

• Under no circumstances should power and logic level wires be bundled together.

• Be sure potenometer tabs do no make contact with the potenometer’s body. Grounding the

•input will cause damage to the drive.

READ ALL SAFETY WARNINGS BEFORE INSTALLING THIS EQUIPMENT

............................................115 VAC ± 10%, 50/60 Hz, single phase

............................................230 VAC ± 10%, 50/60 Hz, single phase

...................................................................................................1.77 at base speed

.............................................................................................1 second

.........................................0 to ± 10 VDC

......................................................................................200K ohms

..................................................................................................3% base speed

........................................................................................................................50:1

...........................................................................................0.5G maximum

...............................................................................................0.1G maximum

...................................................................................10°C - 55°C

..............................................................................................................................0.5 lbs

AC Line Voltage RGH100-5

AC Line Voltage RGH200-5

Form Factor

Acceleraon Time Range

Deceleraon Time Range

Analog Input Voltage Range (Signal must be isolated)

Input Impedance (S0 to S2)

Load Regulaon

Speed Range

Vibraon (0 - 50 Hz)

(>50 Hz)

Ambient Temperature Range

Weight

1/8 - 1/2

Armature

Horsepower

Range

5.0

Connuous

Armature

Current (Amps)

0 - 75

Armature

Voltage Range

(VDC)

115

Line

Voltage

(VAC)

RGH100-5

Model

Specifications

1/4 - 15.00 - 150230RGH200-5

reproduced or retransmied in any form without wrien permission from American Control Electronics®.

The informaon and technical data in this document are subject to change without noce. American

Control Electronics® makes no warranty of any kind with respect to this material, including, but not

limited to, the implied warranes of its merchantability and ﬁtness for a given purpose. American

Control Electronics®assumes no responsibility for any errors that may appear in this document

and makes no commitment to update or to keep current the informaon in this document.

QSG-0080 rev 0

Calibration

Maximum Speed (MAX SPD): The MAX SPD seng determines the maximum motor speed when the

speed adjust potenometer is set for maximum speed. To calibrate the MAX SPD:

1. Set the MAX SPD trim pot full CCW.

2. Set the speed adjust potenometer for maximum speed.

3. Adjust MAX SPD trim pot unl the desired maximum speed is reached.

Forward Torque (FWD TQ) and Reverse Torque (REV TQ): The FWD TQ and REV TQ sengs determine

the maximum torque for accelerang and driving the motor in the forward and reverse direcon.

To calibrate the FWD TQ:

1. With the power disconnected from the drive, connect a DC ammeter in series with the

1. armature.

2. Set the FWD TQ trim pot to minimum (full CCW).

3. Set the speed adjust potenometer to maximum forward speed (full CW).

4. Carefully lock the motor armature. Be sure that the motor is ﬁrmly mounted.

5. Apply line power. The motor should be stopped.

6. Slowly adjust the FWD TQ trim pot CW unl the armature current is 150% of motor rated

6. armature current.

7. Turn the speed adjust potenometer to minimum speed (full CCW).

8. Remove line power.

9. Remove the stall from the motor.

10. Remove the ammeter in series with the motor armature if it is no longer needed.

To calibrate the REV TQ:

1. Follow the steps for calibrang the foward torque using the REV TQ trim pot and with the

1. motor set to run in the reverse direcon.

IR Compensaon (IR COMP): The IR COMP seng determines the degree to which motor speed is

held constant as the motor load changes. To calibrate the IR COMP:

1. Set the IR COMP trim pot full CCW.

2. Increase the speed adjust potenometer unl the motor runs at midspeed without load. A

2. handheld tachometer may be used to measure motor speed.

3. Load the motor armature to its full load armature current rang. The motor should slow down.

4. While keeping the load on the motor, rotate the IR COMP trim pot unl the motor runs at the

4. speed measured in step 2. If the motor oscillates (overcompensaon), the IR COMP trim pot

4. may be set too high (CW). Turn the IR COMP trim pot CCW to stabilize the motor.

5. Unload the motor.

Deadband (DB): The deadband trim pot determines the me that will elapse between the applicaon

of current in one direcon before current is applied in the opposite direcon. The deadband trim pot

aﬀects the resistance that a motor has to changes in sha posion at zero speed. It does this by

applying an AC voltage to the motor armature. Deadband is factory calibrated to approximately the

3 o’clock posion for 60 Hz AC line operaon. Recalibrate the deadband to the 9 o’clock posion for 50

Hz operaon. If you hear motor noise (humming), the deadband might be set too high. Turn the

deadband trim pot CCW unl the motor noise ceases.

Operation

Unidireconal Forward

FWD

50K OHM

SPEED POT

S3 S2 S1 S0

POTENTIOMETER WIRING

Unidireconal Reverse Bidireconal

- Verify that no foreign conducve material is present on the printed circuit board.

1. Turn the speed adjust potenometer full counterclockwise (CCW).

2. Apply AC line voltage.

3. Make sure the drive is enabled.

4. Slowly advance the speed adjust potenometer clockwise (CW). The motor slowly accelerates as

4. the potenometer is turned CW. Connue unl the desired speed is reached.

5. Remove AC line voltage from the drive to coast the motor to a stop.

STARTUP

Startup

REV

50K OHM

SPEED POT

S3 S2 S1 S0

REV

50K OHM

SPEED POT

S3 S2 S1 S0

FWD

Dieses Handbuch passt für folgende Modelle

Andere Ace Gleichstromantrieb Handbücher

Ace

Ace RGH100-5-FLD Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung