Acer NITRO XV272 Bedienungsanleitung

Acer Monitor XV272

LIFECYCLE EXTENSION

GUIDE

Contents

Table of Contents

Important Safety Notice.................................................................................3

1. Exploded Diagram......................................................................................4

2. Wiring connectivity diagram ....................................................................5

3. Mechanical Instruction..............................................................................6

4. Disassembly and Assembly SOP ............................................................7

5. Troubleshooting.......................................................................................13

6. FRU List .....................................................................................................15

Safety Notice

Any person attempting to service this chassis must familiarize with the chassis and be aware

of the necessary safety precautions to be used when serving electronic equipment containing

high voltage

ACER XV272

Important Safety Notice

Product Announcement:

This product is certificated to meet RoHS Directive and Lead-Free produced definition. Using approved

critical components only is recommended when the situation to replace defective parts. Vender

assumes no liability express or implied, arising out of any unauthorized modification of design or

replacing non-RoHS parts. Service providers assume all liability.

Qualified Repairability:

Proper service and repair is important to the safe, reliable operation of all series products. The

service providers recommended by vender should being aware of notices listed in this service

manual in order to minimize the risk of personal injury when perform service procedures.

Furthermore, the possible existed improper repairing method may damage equipment or products. It

is recommended that service engineers should have repairing knowledge, experience, as well as

appropriate product training per new model before performing the service procedures.

NOTICE:

! To avoid electrical shocks, the products should be connect to an authorized power cord, and turn

off the master power switch each time before removing the AC power cord.

! To prevent the product away from water or explosed in extremely high humility environment.

! To ensure the continued reliability of this product, use only original manufacturer’s specified parts.

! To ensure following safety repairing behavior, put the replaced part on the components side of

PWBA, not solder side.

! To ensure using a proper screwdriver, follow the torque and force listed in assembly and

disassembly procedures to screw and unscrew screws.

! Using Lead-Free solder to well mounted the parts.

! The fusion point of Lead-Free solder requested in the degree of 220°C.

ACER XV272

1. Exploded Diagram

1.1 Product Exploded Diagram

Item

ODM DESCRIPTION

Item

ODM DESCRIPTION

ASSY TRIM

MYLAR

PCBA LED BD

MYLAR

LCDM

TAPE

MID-FRAME

TAPE

SCRW

MYLAR

SCRW

WIRE

ASSY SHD

SPK

PCBA CTRL

SCRW

FFC CTRL

PCBA SPS BD

ASSY RC

PCBA IF BD

SCRW

FFC

SCRW

WIRE

ASSY CLMN

PCBA USB BD

ASSY BASE

PCBA USB SIDE BD

FFC

SCRW

ACER XV272

2. Wiring connectivity diagram

There are two types of wiring diagrams for model XV272. The wiring connectivity position will be

different according to the ACTUAL PCBA connector position. Please base on different SKU refer to

below diagram.

NOTE: INF BD= Interface Board, PWR BD=Power Board, CTRL BD= Control Board

1. SKU with USB.

2. SKU without USB.

ACER XV272

3. Mechanical Instruction

Tools Required

List the type and size of the tools that would typically can be used to disassemble the product to a

point

where components and materials requiring selective treatment can be removed.

Tool Description:

- working table

- Screw-driver: Philips-head screwdriver, Hex-head screwdriver

- Knife

- glove

- cleaning cloth

- ESD protection

ACER XV272

4. Disassembly and Assembly SOP

XV272

4.1 Disassembly Procedures

Preparation before disassemble

1.Clean the room for disassemble

2.Identify the area for monitor

3.Check the position that the monitors be placed and the quantity of the monitor ;prepare the area for material flow;

according to the actual condition plan the disassemble layout

4.Prepare the implement, equipment, materials as bellow:

1) working table

2) Screw-driver: Philips-head screwdriver, Hex-head screwdriver

3) knife

4) glove

5) cleaning cloth

6) ESD protection

After unplugging the power cord, the power board still have power energe. Please pay attention

when disassembling/assembling.

Disassemble the RC,

stand and base

Before Disassembling & Assembling, monitor need to be put on the sponge and

the Insulation glove must be wore during the process.

Disassemble base and stand from the RC(Rear Case) as picture 1.

Unlock RC center screw as picture 1.

Disassemble RC from monitor and extract the FFC CTRL from the IF BD as picture 2.

PICTURE 1 PICTURE 2

Disassemble CTRL BD

Tear off the adhesive tape of the FFC CTRL from the RC as picture 1.

Disassemble the CTRL BD from the RC as picture 2.

Disassemble the FFC CTRL from the CTRL BD.

PICTURE 1 PICTURE 2

CTRL BD

ACER XV272

Disassemble SPK and

Lamp wire

Tear off 4 tapes of the SPK wire, extract the SPK wire from the IF BD and disassemble

the SPK from the MF as picture 1.

Extract the LED wire from the IF BD and tear off the wire from the SHD as picture 1 in

green frame.

Tear off the black tape of the lamp wire, tear off black mylar on SHD and extract the

lamp wire from the P/BD as picture 2

PICTURE 1 PICTURE 2

Disassemble USB SIDE

Tear off the small Mylar from the SHD as picture 1.

Extract the USB FFC from USB BD and tear off the USB FFC from the panel as picture

Unlock the USB screw from the USB IF BD and disassemble the USB IF BD from the

MF as picture 3.

Extract The USB FFC from the USB IF BD.

PICTURE 1 PICTURE 2 PICTURE 3

Disassemble ASSY

Trim

Unlock 2 TRIM screws and disassemble the ASSY TRIM from the MF as picture 1.

Disassemble the LED BD from the Trim and extract the LED wire from the LED BD as

picture 2.

PICTURE 1 PICTURE 2

LED BD

USB BD

ACER XV272

Disassemble SHD and

MF.

Tear off tapes and extract FFC wire from the panel as picture 1.

Unlock 9 screws from the MF and disassemble the MF from the Pane as picture 2.

Extract the lamp wire from the panel as picture 2.

PICTURE 1 PICTURE 2 PICTURE 3

Disassemble I/F BD

and P/BD.

Remove Mylar and ulock 7 PCBA screws and 1 DP screw from the PCBA BD.

Disassemble the USB BD from the SHD and extract the USB wire from the USB BD as

picture 2.

Disassemble the I/F BD from the SHD and extract the P/BD wire and 2 FFC LVDS from

the I/F BD.

Disassemble the P/BD from the SHD.

PICTURE 1 PICTURE 2

NOTE: Circuit boards >10 cm² has been highlighted with the yellow rectangle as above image shows.

Please detach the Circuit boards and follow local regulations for disposal.

I/F BD

P/BD

USB BD

ACER XV272

4.2 Assembly Procedures

Preparation before assemble:

1.Clean the room for work

2.Identify the area for material

3.Prepare the implement, equipment, materials as bellow：

1) working table

2) Screw-driver: Philips-head screwdriver, Hex-head screwdriver

3) Knife

4) Glove

5) Cleaning cloth

6) ESD protection

After unplugging the power cord, the power board still have power energe. Please pay attention when

disassembling/assembling.

Assemble I/F BD and P/BD

from SHD.

Before Disassembling & Assembling, monitor need to be put on the sponge and

the Insulation glove must be wore during the process.

Assemble the P/BD to the SHD as picture 1.

Insert the FFC LVDS, P/BD wire and USB wire to the IF BD and assemble the IF BD to

the SHD as picture 2.

Insert USB wire to the USB BD and assemble the USB BD to the SHD; then lock 7 PCBA

screws and 1 DP screw as picture 3.

PICTURE 1 PICTURE 2 PICTURE 3

Assemble Panel to MF

Take the Panel and insert lamp wire to panel marked as picture 1.

Assemble the MF to the panel and lock 9 screws to the MF as picture 2.

Stick 1 piece of adhesive tape on the little connector of lamp wire as picture 3.

PICTURE 1 PICTURE 2 PICTURE 3

P/BD

I/F BD

P/B

P/BD

USB BD

Andere Handbücher für NITRO XV272

Inhaltsverzeichnis

Andere Acer Monitor Handbücher

Acer

Acer BM320 Bedienungsanleitung

Acer

Acer V193WEJB Bedienungsanleitung

Acer

Acer XF251Q Bedienungsanleitung

Acer

Acer NITRO XV272 Bedienungsanleitung

Acer

Acer AC511 SERIES Bedienungsanleitung

Acer

Acer X163W Bedienungsanleitung

Acer

Acer X203Wbd Bedienungsanleitung

Acer

Acer packardbell viseo 193ws Bedienungsanleitung

Acer

Acer T230H - Bmidh Wide Touch Screen Display Bedienungsanleitung

Acer

Acer AL2017 Bedienungsanleitung

Acer

Acer XF3 Series Bedienungsanleitung

Acer

Acer RG270 Bedienungsanleitung

Acer

Acer LCD monitor Bedienungsanleitung

Acer

Acer CBA322QU Bedienungsanleitung

Acer

Acer KA220HQ bid Bedienungsanleitung

Acer

Acer LCD monitor Bedienungsanleitung

Acer

Acer Ferrari F-17 Bedienungsanleitung

Acer

Acer B223W - Bdmr - 22" LCD Monitor Bedienungsanleitung

Acer

Acer S232HL Bedienungsanleitung

Acer

Acer KA272 Bedienungsanleitung

Acer

Acer Awmidx ED322Q Bedienungsanleitung

Acer

Acer XF270H Bedienungsanleitung

Acer

Acer G196HQL Bedienungsanleitung

Acer

Acer 99sl Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung

LG M1950D-PZ Bedienungsanleitung