Acer V551 Bedienungsanleitung



Acer V551 (new) CRT Monitor Service Guide

Chapter 3 Alignment Procedure

Confidence and Property

Table of Contents

0. Preparation for Alignment............................................................................................................. 2

1. B+ Adjustment (For function test station only) ............................................................................ 2

2. Geometry Adjustment................................................................................................................... 2

3. Background Adjustment................................................................................................................ 3

4. Foreground Adjustment ................................................................................................................ 3

5. Final Check................................................................................................................................... 3

6. Focus Adjustment ......................................................................................................................... 4

7. Convergence Adjustment.............................................................................................................. 4

8. Power Saving Function Check...................................................................................................... 4

9. Geometry Specification for Production Line................................................................................ 5

10. Eyelet parts.................................................................................................................................. 5

11. Touch-up parts ............................................................................................................................ 7

12. Glue parts.................................................................................................................................... 8

13. Wire Dressing parts..................................................................................................................... 9



Acer V551 (new) CRT Monitor Service Guide

Chapter 3 Alignment Procedure

Confidence and Property

0. Preparation for Alignment

a. Pre-set all VRs to the center position except R/G/B bias VR101, 102, 103 counterclockwise to

maximum.

b. Set up unit and keep it warm up at least 15 minutes.

c. Preset mode

IBM VGA 640X480 31.5KHz/60Hz

IBM VGA 640X400 31.5KHz/70Hz

6448A 640X480 37.5KHz/75Hz

SVGA4 800X600 46.88KHz/75Hz

SVGA3 800X600 48.09KHz/72Hz

SVGA5 800X600 53.6KHz/85Hz

1. B+ Adjustment : (For function test station only)

a. Input mode 53.6KHz (SVGA5) with cross hatch pattern.

b. Press "SELECT +" and "ADJUST -" keys at a same time.

c. Adjust switching power supply VR601 to make the horizontal B+ to be 50.0 +/- 0.2VDC.

2. Geometry Adjustment

a. Enter factory area -- Press "SELECT +" and "ADJUST-" at the same time then turn power

switch on.

b. Press "ADJUST +" and "ADJUST -" at the same time to clear user area.

c. Input mode 31.5KHz (VGA 640x480) with tilt adjustment pattern.

d. Adjust CRT screw to meet tilt and orthogonal spec. ( Tilt < ±1 mm , Orthogonal < ±1.5mm )

e. Input the presetting modes and supporting modes with full white pattern.

f. Set external contrast to maximum and brightness to raster just cut-off position.

g. Press "SELECT +" or "SELECT -" to select the adjustment for H-size, H-phase, V-size,

V-center, Pincushion or Trapezoid.

h. Press "ADJUST +" or "ADJUST -" to make the geometry can meet item 9 table 2 spec.

i. Press "SELECT +" and "ADJUST -" at the same time to save the adjustment data.

j. Change timing to next mode and repeat step f, g and h.

k. After all modes are adjusted OK, turn power switch off.



Acer V551 (new) CRT Monitor Service Guide

Chapter 3 Alignment Procedure

Confidence and Property

3. Background Adjustment

a. Enter factory area -- Press "SELECT +" and "ADJUST -" at the same time then turn power

switch on.

b. Input mode 53.6KHz (SVGA5) with raster only pattern.

c. Adjust external brightness key to maximum.

d. Check the bias VRs of VR101, 102, 103 at counterclockwise maximum position.

e. Adjust screen VR of FBT to obtain twilight raster about 0.7 to 1.2 Ft-L.

f. See which gun appears first, then adjust the two bias VRs of the other two non-appearing guns to

achieve the color temperature meet specification x=0.281 +/- 0.005

y=0.311 +/- 0.005

g. Adjust screen VR of FBT again to let the raster about 0.7 to 1.2 Ft-L.

4. Foreground Adjustment

a. Input mode 53.6KHz (SVGA5) with 3-inch block pattern.

b. Check the drive VRs of VR104, 105 at center position.

c. Adjust external brightness key to cut-off and external contrast key to let the light output be 15

Ft-L,

d. Adjust VR103, 104 to let the color temperature meet the specification x=0.281 +/- 0.003

y=0.311 +/- 0.003

e. Adjust external contrast key to let light output be 45±3 Ft-L.

f. Press "SELECT +" and "ADJUST -" to save the adjustment data.

g. Adjust VR301 to let light output be 31±0.5 Ft-L.

h. Turn power switch off.

5. Final Check

a. Enter final check area -- press "SELECT +" and "ADJUST +" at the same time then turn power

switch on.

b. Input mode 53.6KHz (SVGA5) with full white pattern.

c. Press "SELECT +" and "ADJUST -" keys at a same time.

d. Check the light output is greater than 30Ft.L.

e. Adjust external contrast and brightness keys to minimum, the video and raster should be

disappear.

f. Check the performance of all modes can meet spec.



Acer V551 (new) CRT Monitor Service Guide

Chapter 3 Alignment Procedure

Confidence and Property

6. Focus Adjustment

a. Input mode 53.6KHz (SVGA5) with characters pattern.

b. Press "SELECT +" and "ADJUST -" keys at a same time.

c. Adjust focus VR of FBT to make "A" area focus clear.

video

raster

7. Convergence Adjustment

a. Input mode 53.6KHz (SVGA5) with purple cross hatch pattern.

b. Adjust 4-pole magnetic ring of Yoke to meet specification.

c. Input mode 53.6KHz (SVGA5) with yellow cross hatch pattern.

d. Adjust 6-pole magnetic ring of Yoke to meet specification.

e. Input mode 53.6KHz (SVGA5) with white cross hatch pattern.

f. Re-confirm the mis-convergence can meet spec.

B D

A A ≦0.2 mm

C E

B,C,D,E ≦0.3 mm

8. Power Saving Function Check

a. Input mode 53.6KHz (SVGA5) with full white pattern.

b. Set external contrast and brightness keys to maximum position.

c. Remove H-Sync only, the video and raster should be extinguished. The LED shows amber color

and the power consumption should be less than 60W.

d. Remove V-Sync only, the video and raster should be extinguished. The LED shows amber

color and the power consumption should be less than 5W.

e. Remove both H and V Sync, the power consumption should be less than 5W and LED shows

amber color.

f. Input H-Sync and V-Sync, the video should be exhibited again and LED on (green).



Acer V551 (new) CRT Monitor Service Guide

Chapter 3 Alignment Procedure

Confidence and Property

9. Geometry Specification for Production Line

(Table 2)

ITEM DESCRIPTION SPECIFICATION

1 HORI SIZE 270 ±4 mm

2 VERT SIZE 202 ±4 mm

3 SIDE PIN ≦2.0 mm

4 TOP/BOTTOM PIN ≦1.0 mm

5 SIDE BARREL ≦1.0 mm

6 TOP/BOTTOM BARREL ≦1.0 mm

7 TRAPEZOID ≦1.0 mm

8 VIDEO OFFSET ≦4.0 mm

9 PARALLELGRAM ≦2.0 mm

10 HORI LINEARITY ≦5 %

11 VERT LINEARITY ≦5 %

10. Eyelet parts

1. Q602 Heat sink



Acer V551 (new) CRT Monitor Service Guide

Chapter 3 Alignment Procedure

Confidence and Property

2. T303

3. IC202 Heat sink/ T302

4. M101 CRT socket



Acer V551 (new) CRT Monitor Service Guide

Chapter 3 Alignment Procedure

Confidence and Property

11. Touch-up parts

The component listed below must touch-up to avoid solder crack.

1. Q310: 3 points

2. D307: 3 points

3. L302: 2 points

4. CN601: 3 points



Acer V551 (new) CRT Monitor Service Guide

Chapter 3 Alignment Procedure

Confidence and Property

5. Q602: 3 points

6. C612: 2 points

7. M101: 8 points

12. Glue parts

1. G2 & G4 VR add glue to fix the position of VR



Acer V551 (new) CRT Monitor Service Guide

Chapter 3 Alignment Procedure

Confidence and Property

2. R607 add glue to fix the Heat sink

13. Wire Dressing parts

1. Left side view:

2. Right side view:



Acer V551 (new) CRT Monitor Service Guide

Chapter 3 Alignment Procedure

Confidence and Property

3. Rear side view:

4. Left/Bottom degaussing fixed

5. Right/Bottom degaussing fixed

Inhaltsverzeichnis

Andere Acer Monitor Handbücher

Acer

Acer S240HL Bedienungsanleitung

Acer

Acer UM.WV7AA.302 Bedienungsanleitung

Acer

Acer V226HQL Bedienungsanleitung

Acer

Acer B273H Bedienungsanleitung

Acer

Acer G215HL Bedienungsanleitung

Acer

Acer G185H Bedienungsanleitung

Acer

Acer P215H Series Bedienungsanleitung

Acer

Acer V173 Bedienungsanleitung

Acer

Acer AcerView 78c Bedienungsanleitung

Acer

Acer ConceptD CP7 Bedienungsanleitung

Acer

Acer AL1922 r Bedienungsanleitung

Acer

Acer PM181Q Bedienungsanleitung

Acer

Acer KA0 KA270HBbid Bedienungsanleitung

Acer

Acer AL1515 Bedienungsanleitung

Acer

Acer LCD monitor Bedienungsanleitung

Acer

Acer FP855 Bedienungsanleitung

Acer

Acer G247HL Bedienungsanleitung

Acer

Acer KG251QDbmiipx Bedienungsanleitung

Acer

Acer XFA240 Bedienungsanleitung

Acer

Acer G235HL Bedienungsanleitung

Acer

Acer AL2023 Bedienungsanleitung

Acer

Acer X223W - 22" Widescreen LCD Monitor Bedienungsanleitung

Acer

Acer XV280K Bedienungsanleitung

Acer

Acer R240HY Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung

LG M1950D-PZ Bedienungsanleitung