ACME COOLIE 545 Bedienungsanleitung

CONTENTS

1. Safety Instructions.................................................................................................. 2

2. Technical Specifications .......................................................................................... 4

3. How To Set The Unit ............................................................................................... 5

3.1 Control Panel .................................................................................................... 5

3.2 Main Function .................................................................................................. 6

4. Control By Universal DMX Controller.................................................................... 12

4.1 DMX512 Connection ...................................................................................... 12

4.2 Address Setting............................................................................................... 13

4.3 DMX512 Configuration ................................................................................... 13

5. Troubleshooting ................................................................................................... 16

6. Fixture Cleaning ................................................................................................... 16

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer

will not accept liability for any resulting defects or problems.

Unpack and check carefully that there is no transportation damage before using the unit.

This product is suitable for wet locations. Do not immerse in water.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head

only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.

DO NOT connect the device to any dimmer pack.

Make sure there are no flammable materials close to the unit while operating to avoid fire

hazard.

Examine the power wires carefully; replace them immediately if there is any damage.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happens, cut

off the mains power immediately.

DO NOT operate in dirty or dusty environment, do clean fixtures regularly.

Please read the instruction carefully which includes important information

about the installation, usage and maintenance.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together twist other cables.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the unit as there are no user serviceable parts inside.

Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance center if

needed.

Disconnect the mains power if the fixture is has not been used for a long time.

DO use the original packing materials before transporting it again.

DO NOT look directly at the light while the LED is on.

DO NOT start on the unit without LED enclosure or when housing is damaged.

Installation:

The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating and make sure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of the

fixtures weight. Always use a safety cable that can hold 12 times of the weight of the fixture when

installing.

The equipment must be installed by professionals. It must be installed in a place where is out of

the reach of people and no one can pass by or under it.

2. Technical Specifications

Power Voltage:

AC 100~240V, 50/60Hz

Power Consumption:

170W

Light Source:

54x3W RGBW LED

Beam Angles:

19°

Control:

DMX Channel: 4/5/7 channel

Control Mode: DMX, Primary/Secondary

Firmware Upgrade: Update via DMX link

Construction:

Display: LED display

Data In/Out Socket: 3-pin XLR socket

Protection Rating: IP66

Features:

Outstanding color mixing effect

Preset program in stand-alone mode

4 dimming curves, 0~100% smooth dimming

Various strobe speeds

Dimension/Weight:

302x230x350mm, 9.1kgs

11.9”x9.1”x13.8”in, 20.1lbs

Photometrics Diagram:

3. How To Set The Unit

3.1 Control Panel

1. POWER IN/OUT:

Water proof connectors for power input/output

2. DMX IN/OUT:

Water proof connectors for DMX 512 operation, use 3-pin XLR cable to link the units together

3. Display:

To show the menu and the selected functions

Button:

4. MENU To select the programming functions

5. DOWN To go forward in the selected functions

6. UP To go backward in the selected functions

7. ENTER To confirm the selected functions

3.2 Main Function

Turn on the unit, press the MENU button into menu mode, and press the UP/DOWN button until

the required function is shown on the monitor. Select the function by the ENTER button. Use the

UP/DOWN button to choose the submenu, press the ENTER button to store and automatically

return to the last menu. Press the MENU button or let the unit idle 30 seconds to exit menu mode.

The main functions are shown below:

Once you set to , after running in show mode for 5 minutes

without any change or restarting the unit, the key board become locked.

Press ENTER button to enable the menu, the display will show , press

UP and DOWN button until it shows , then press ENTER to unlock.

DMX Address

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to change the DMX 512 address. Once the

address has been selected, press ENTER button to setup or automatically exit menu mode without

any change after 30 seconds. Back to the previous functions without any change press MENU

button.

Channel Mode

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (4 channels),

(5 channels) or (7 channels). Once select, press ENTER button to setup or

automatically exit menu mode without any change after 30 seconds. To go back to the functions

without any change press the MENU button.

Show Mode

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (show 1) …

(show 16) or (Manual). After select the show mode, use DOWN and UP button to

adjust the value for fade mode and speed mode. Once select, press ENTER button to store or

automatically return to the main functions without any change after 30 seconds. To go back to the

previous functions without any change press the MENU button.

Primary/Secondary Mode

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Primary),

(Secondary 1) or (Secondary 2). Once select, press ENTER button to store or

automatically return to the main functions without any change after 30 seconds. To go back to the

previous functions without any change press the MENU button.

Dimmer Curve

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Dimmer Curve

1) … (Dimmer Curve 4). Once select, press ENTER button to store or automatically return

to the main functions without any change after 30 seconds. To go back to the previous functions

without any change press the MENU button.

Dimmer Speed

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Smooth) or

(Fast). Once select, press ENTER button to store or automatically return to the main

functions without any change after 30 seconds. To go back to the previous functions without any

change press the MENU button.

DMX Status

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Primary/Secondary

Mode) or (Blackout Mode). Once select, press ENTER button to store or automatically

return to the main functions without any change after 30 seconds. To go back to the previous

functions without any change press the MENU button.

LED

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (On) or

(Off). Once select, press ENTER button to store or automatically return to the main functions

without any change after 30 seconds. To go back to the previous functions without any change

press the MENUbutton.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME Leuchte Handbücher

ACME

ACME GEIST BEAM Bedienungsanleitung

ACME

ACME led-st05 Bedienungsanleitung

ACME

ACME MH-6616S Bedienungsanleitung

ACME

ACME Xperior 5R BEAM F Bedienungsanleitung

ACME

ACME Aeco 20 Bedienungsanleitung

ACME

ACME LED?MS700PE Bedienungsanleitung

ACME

ACME Xperior XP-16R BEAM II Bedienungsanleitung

ACME

ACME LED-MB500 Bedienungsanleitung

ACME

ACME LPB-4P Bedienungsanleitung

ACME

ACME CM-70Z Bedienungsanleitung

ACME

ACME Led Strobe 20 LED-ST20 Bedienungsanleitung

ACME

ACME Xperior XP-16R SZ Bedienungsanleitung

ACME

ACME VB-8-10FC Bedienungsanleitung

ACME

ACME Xperior 5R BEAM F Bedienungsanleitung

ACME

ACME xperior 15R spot XP-15R SZ Bedienungsanleitung

ACME

ACME XP-5000 SZ NF Bedienungsanleitung

ACME

ACME LED BEAM 350 Bedienungsanleitung

ACME

ACME GLAMOUR 700Z RGBY Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung