ACOPOWER 3x40W Bedienungsanleitung
560mm (22in)
440mm
(17.3in）
4
5
1
3
7
2
6
8
9
560mm(22in)
1440mm(56.7in)
Product Introduction
3×40W
Introduction
1 3x40 Watts Solar Panel
2 10A Charge Controller
3 Alligator clips
4 Suitcase with handle and pocket
5 Stands
6 MC4 Connectors (two pairs, removable)
7 Cable 14AWG 15ft
8 Cable 14AWG 3ft
9 Fuse
Items
3×40W
This portable solar panel comes with a pre-installed charge controller. This charge controller
protects battery against unsafe electrical conditions and must be used to charge 12V batteries. To
charge solar generators with a built-in charge controller, simply use the MC4 cables provided and
plug them into the cables that came with your power station to charge. A 12V battery and solar
generator can be charged at the same time.
Features
User’s guide
3×40W
• Max 120 watts solar panel
• 10A PWM charge controller with USB output
• Portable
• Removable MC4 Connectors
• Charge 12V battery by alligator clamps- Sealed, Flooded, GEL, AGM, Lithium and other deep
cycle batteries
• Charge 12V solar generator by MC4 adapter- battery with inverter, power bank/station with built-in
charge controller. ACOPOWER solar generator 150Wh and 220Wh recommended
• Can be used on its own or as part of a larger solar system
• Extendable with MC4 Connectors
After receiving the solar panel kit, please check if all accessories are included in the package and
prepare to test your kit:
1. Locate a sunlit area clear from hanging branches or obstacles.
2. Unfold the solar panels and face the front towards the sun.
Tip: To obtain the maximum output power of solar modules, it is recommended to adjust the solar
modules based on solar trajectory.
3×40W
How to test the solar panel
Method 1: use a multi-meter
Set your multi-meter to measure DC voltage and put the red probe on the red MC4 cable and the
black probe on the black MC4 cable (this is the solar panel’s direct output), make sure the
connections are secure. the open-circuit voltage should be displayed on your multi-meter and it
should be around 17.6V-23V.
If you’re not getting something within that range or close to those numbers, you should check and
make sure the solar panel is in direct sunlight and that the connections between the MC4 cables
and the multi-meter is secure.
3×40W
Method 2: use your solar generator
To test if the solar panel is working with a solar generator with a built-in charge controller,
connect the MC4 adapters that came with your solar generator and plug it in to the MC4 cables
of the solar panel directly (Bypassing the charge controller). Turn your solar generator on and it
should start charging from the solar panel.
3×40W
How to test if the charge controller is working
Step 1: Clamp the red battery clip to positive, black to negative and make sure the connection
is secure. Make sure the solar panel MC4 cables are connected to the MC4 cables of the
charge controller.
Step 2: When all the connections are complete, the charging status indicator should light up if
the solar is under direct sunlight AND the battery is connected to the charge controller.
(Detailed information under Specifications section)
3×40W
Tip: The charge controller and the USB port will not respond unless it is connected to a battery!
Always connect the battery first, then load (if applicable) and then the solar panel.
For lights explanation, please check the Specifications section.
What are you going to use it for
1. Charge solar generators
1.1. Charge 12V Solar Generator with built-in Charge Controller
Step 1: understand your solar generator and prepare the MC4 adapter for your solar generator
Step 2: Disconnect MC4 Connectors and let it to be a solar panel with MC4 connectors
Step 3: Use your MC4 Adapter to charge your solar generator
3×40W
2. Charge your 12 Volt battery
The solar panel kit is designed to charge a large range of batteries including Sealed, Flooded, GEL,
AGM, Lithium, lead-acid battery and other deep cycle battery. The batteries are used as car battery,
RV battery, boat battery and emergency back-up battery.
Step 1: understand your battery: battery type, capacity and voltage
Step 2: check the charge controller’s set up. We have defaulted the setting of the charge
controller is for SEALED. (AGM is also included in SEALED type.) If your battery’s type is different,
please set your battery type with the charge controller following the instructions below.
The battery type setting method (on charge controller)
Press and hold the program button for more than 5 seconds, the battery indicator LED1, LED2,
LED3 will flash accordingly. Press the button again to set up the exact battery type, after the
selection, wait 5 seconds, no flashing lights means battery setting is completed, the specific
content of the following table indicates
Sealed Lead Acid Battery (Sealed)
Colloidal lead-acid batteries(Gel)
Opening lead-acid batteries(Flooded)
LED1 LED2 LED3 Battery Type
○× ×
○×
○
○
○ ○
Note: "○" means lights on "×" means lights off
3×40W
3. Join your current solar system by Parallel or Series Circuit
Step 1: Disconnect MC4 Connectors from the charge controller
Step 2: Connect panel with your current system with MC4 connectors. More connectors
and extension cables may be needed.
Specifications
80W Foldable solar panel
3×40W
560×440×20
22×17.3×0.8(inches)
1440×560×4
56.7×22×0.2(inches)
3.8
(8.4 lb) 120 20.88
Max-power
Cuurrent
Open-Circuit
Cuurrent
Max
Power
Open
Power
Voltage
Short-Circuit
Cuurrent
N.M
Module Size
Module
Type
Kg WW mm mm V VA A
5.97 24.64 6.32
Folded size Unlded size
The load switch setting method:
When the controller is on (battery connected), press the Set button to control load output. Use this
button to turn the load ON or OFF.
Tip: The USB port will only output when the Load is set to ON.
3×40W
②
①
③
④
⑤
⑥
⑦
⑧
NOTE: Unplug the RTS,
the temperature of
battery will be set
to a fixed
value 25ºC.
!
Wiring
①
LCD
⑤
Battery Terminals
②
MENU Button
⑥
Load Terminals
③
RTS Port
⑦
SET Button
④
PV Terminals
⑧
USB Output Ports
※
※ USB output ports provide the power supply of
circuit protection.
Figure 1 Characteristic
5VDC/2.4A and have the short
Optional Accessory:
Name: Remote Temperature Sensor
Model:RTS300R47K3.81A
Acquisition of battery temperature for undertaking
temperature compensation of control parameters,
the standard length of the cable is 3m (length can
be customized). The RTS300R47K3.81A connects to
the port ③on the controller.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere ACOPOWER Solarpanel Handbücher
ACOPOWER
ACOPOWER POWERECO PE-PTK-100WPX20A Bedienungsanleitung
ACOPOWER
ACOPOWER HY-PTK-100WP20A Bedienungsanleitung
ACOPOWER
ACOPOWER KIT-HYS60MB Bedienungsanleitung
ACOPOWER
ACOPOWER KIT-HYS200MB Bedienungsanleitung
ACOPOWER
ACOPOWER KIT-HYS100MB Bedienungsanleitung
ACOPOWER
ACOPOWER KIT-HYS100MB Bedienungsanleitung
ACOPOWER
ACOPOWER HY-PTK-120WPX20A Bedienungsanleitung
ACOPOWER
ACOPOWER HY-PTK-100Exp Bedienungsanleitung
ACOPOWER
ACOPOWER HY-PTK-100WPX20A Bedienungsanleitung
ACOPOWER
ACOPOWER HY-SPKP-400W40A Bedienungsanleitung
