Acrosser Technology ACE-B7400 Installationsanleitung

P/N：2200104-G

ACE-B7400

Quick Manual

P/N：2200104-G

ACE-B7400 Quick Manual

1.Mainboard illustration (Top Side)

IO Conpoments and KEY Parts illustration:

P/N：2200104-G

Note1: PWR_BTN can be used as a Power-Button to power-on system when FPIO1/3-4 is not

shroted. If FPIO1/3-4 is shroted by a jumper-head, system will automatically boot-up when power

applied.

Note2: Please Refer to Page8 for Rears-Panel IO Configurations.

Note3: AMD eOntario Platform supports maximum totle 8GB DDRIII Memory.

LED1

Green LED: Powered On.

Orange LED: HDD Active.

CN7

Gaming Input Isolation Connector.

(note2)

CF1

CF Card Slot 1.

PWR_BTN1

System Power Button. (note1)

CN6

Gaming Input Isolation Connector.

(note2)

CF2

CF Card Slot 2.

DVI-D1

DVI-D Connector.

CN4

Gaming Open-Drain Output

Connector. (note2)

U40

Acrosser Gaming Core.

DVI-I1

DVI-I Connector.

CN4

Gaming Open-Drain Output

Connector. (note2)

SATA1/SATA2

SATA 3.0 Connectors.

USB1

Dual-Port USB 2.0 Connector

(USB 5, 6).

CN3

Selectable TTL, RS232, RS485,

cctalk Connector (UART Port 5, 6).

MINI-PCIE1

Mini-PCIe Slot.

CN25

One RJ45 with Dual USB 2.0

Connector (LAN 2 & USB 3, 4).

CN2

2.1 Channel Audio Amplifier Output

Connector.

CN_DIMM1/CN_DIMM2

DDR3 SODIMM Socket.

(note3)

CN26

One RJ45 with Dual USB 2.0

Connector (LAN 1 & USB 1, 2).

CN1

System Power Input Connector.

CASESW1

Micro-switch for Chassis

Open/Close Detection.

COM1_2

UART RS-232 Port 1, 2

(Supports 9-bits Protocol).

U43

AMD FT1 APU. (T48N/T52R) BAT_BH1

System RTC Battery Holder.

COM3_4

UART RS-232 Port 3, 4.

U44

AMD Hudson-E1 Fusion Controller

Hub.

P/N：2200104-G

2. Connector & Jumper setting definition (Top Side)

FPIO1

System Power Button

Pin-header & Reset Jumper.

SATA_PWR1/SATA_PWR2

Two JST 2.5mm SATAPower

Connectors.

BAT_A1, BAT_B1

Lithium Battery Connector for

SRAM, AGA and secured RTC.

CN_USB1

JST 2.0mm USB Connector

(USB7).

CN19

Clear System CMOS Jumper.

JP18

RS-485 Terminal Resistor

Selection Jumper for UART 6.

CN_USB2

JST 2.0mm USB Connector

(USB8).

JP6 ~ JP13

CN3 Output Signal Selection

Jumper.

JP17

RS-485 Terminal Resistor

Selection Jumper for UART 5.

SYSFAN2

System FAN Connector 2. SYSFAN1

System FAN Connector 1.

AUDIO1

Internal 5.1 Channel Audio

Pin-Header.

APUFAN1

APU FAN Connector.

IButtom2

JST 2.0mm External i-Button

Connector.

JP1

cctalk Supply Power Selection

Jumper.

SPAREIO1

JST 2.0mm Gaming Spare-IO

Connector. (16-bits GPIO)

JP2/JP3

SRAM A, B Clear Jumper.

CASESW2

JST 2.0mm Chassis Open/Close

Detection Connector.

SW1

8-bit DIP-Switch Input forAGC.

JP4/JP5

Bill-enable, Coin-enable

Preset Jumper.

P/N：2200104-G

2.1 Connectors and Jumpers Setting

2.1.1 FPIO1

System Power button & Reset Jumper. 2.1.2 CN_USB1

JST 2.0mm USB Connector (USB7).

JUMPER FUNCTION

1-2 External Power Button

Connection

3-4 Short to Enable Auto

Power-on Function.

5-6 System Reset Button

Connector

PIN SIGNAL

1 VCC (+5V)

2 Data+

3 Data-

4 GND

5 N.C

2.1.3 CN_USB1

JST 2.0mm USB Connector (USB7). 2.1.4 SYSFAN2

System FAN Connector 2.

PIN SIGNAL

1 VCC (+5V)

2 Data+

3 Data-

4 GND

5 N.C

PIN SIGNAL

1 GND

2 +12V

3 Feedback

2.1.5 APUFAN1

APU FAN Connector. 2.1.6 SPAREIO!

JST 2.0mm Gaming Spare-IO Connector.

PIN SIGNAL

1 GND

2 +12V

3 Feedback

PIN SIGNAL PIN SIGNAL

1 Bit0 2 Bit8

3 Bit1 4 Bit9

5 Bit2 6 Bit10

7 Bit3 8 Bit11

9 Bit4 10 Bit12

11 Bit5 12 Bit13

13 Bit6 14 Bit14

15 Bit7 16 Bit15

17 GND 18 +3.3V

19 GND 20 +3.3V

P/N：2200104-G

2.1.7 SW1

8-bits DIP-Switch Input for AGC. 2.1.8 SATA_PWR1/ SATA_PWR2

Two JST 2.5mm SATA Power Connectors.

PIN SIGNAL

ON +3.3V

OFF GND

PIN SIGNAL

1 +12V

2 GND

3 +3.3V

4 +5V

2.1.9 CN19

Clear System CMOS Jumper. 2.1.10 JP6 ~ JP13

CN3 Output Signal TTL/RS232/RS485/cctalk

Selection Jumper.

JUMPER FUNCTION

1-2 (default) Normal

2-3 Clear CMOS

Please See Appendix A.

2.1.12 IBUTTON2

JST 2.0mm External i-Button Connector. 2.1.13 JP2/JP3

SRAM A, B Clear Jumper.

PIN SIGNAL

1 I-Button Signal

2 GND

JUMPER FUNCTION

1-2 (default) Normal

2-3 Clear SRAM

P/N：2200104-G

2.1.14 JP4/JP5

Bill-enable, Coin-enable Preset Jumper. 2.1.15 BAT_A1/BAT_B1

Lithium Battery Connector for SRAM, AGA

and secured RTC.

JUMPER FUNCTION

1-2 (default) Preset is “High”.

2-3 Preset is “Low”.

“High” means Bill-enable, Coin-enable

open-drain output is short to ground.

“Low” means Bill-enable, Coin-enable

open-drain output is open

PIN SIGNAL

1 POWER

2 GND

2.1.16 JP18

RS-485 Terminal Resistor Selection Jumper

for UART6.

2.1.17 JP17

RS-485 Terminal Resistor Selection Jumper

for UART5.

JUMPER FUNCTION

1-2 (default) Termination

2-3 Non

RS-485 terminal resistor is 120ohm.

JUMPER FUNCTION

1-2 (default) Termination

2-3 Non

RS-485 terminal resistor is 120ohm.

2.1.18 AUDIO1

Internal 5.1Channel Audio Pin-Header. 2.1.19 JP1

ccTalk Supply Power Selection Jumper.

PIN SIGNAL PIN SIGNAL

1 Front-L 2 Front-R

3 GND 4 GND

5 Surround-L 6 Surround-R

7 IO4 GND 8 GND

9 Center 10 LFE

JUMPER FUNCTION

1-2 (default) +12V

2-3 +24V

+24Vpower is from CN1 external power supply.

2.1.20 CASESW2

JST 2.0mm Chassis Open/Close Detection

Connector.

PIN SIGNAL

1 Signal

2 GND

P/N：2200104-G

2.2 Rears-Panel IO Configurations

CN1 System Power Input Connector (Micro-FIT 3.0mm 2*4 PINs)

PIN SIGNAL PIN SIGNAL

1 +12V Input 5 +12V Input

2 GND 6 GND

3 GND 7 GND

4 +12V Input 8 +24V Input

Note:

1. +12V Power Input voltage tolerance is ±10%.

2. +24V Power Input is only use for cctalk Vs power supply.

CN2 2.1 Channel Audio Amplifier Output Connector (Micro-FIT 3.0mm 2*3 PINs)

PIN SIGNAL PIN SIGNAL

1 Amplified Front Left + 4 Amplified Front Left -

2 Amplified Front Right + 5 Amplified Front Right -

3 Amplified LFE + 6 Amplified LFE -

Note:

1. ACE-B7400 with Audio Amplifier is D-type amp.

2. Amplified Right and Left channel support 10Watt(max) Output, Amplified LFE channel supports 20Watt(max) Output.

CN3 Selectable TTL, RS232, RS485, cctalk Connector (Micro-FIT 3.0mm 2*7 PINs)

Pin Signal Signal Pin

1 COM5 TTL/ 232 Tx/ 485 + COM5 TTL/ 232 Rx/ 485 - 8

2 COM6 TTL/ 232 Tx/ 485 + COM6 TTL/ 232 Rx/ 485 - 9

3 COM5 ccTalk Data COM6 ccTalk Data 10

4 COM5 ccTalk Vcc COM6 ccTalk Vcc 11

5 GND GND

6 GND GND

7 GND GND

P/N：2200104-G

CN4/CN5 Gaming IO Output Connector (Micro-FIT 3.0mm 2*10 PINs)

CN4: Pin Signal Pin Signal

1 LAMP 1 11 LAMP 9

2 LAMP 2 12 LAMP 10

3 LAMP 3 13 LAMP 11

4 LAMP 4 14 LAMP 12

5 LAMP 5 15 LAMP 12

6 LAMP 6 16 Tower LAMP 1

7 LAMP 7 17 Tower LAMP 2

8 LAMP 8 18 Tower LAMP 3

9 GND 19 GND

10 GND 20 GND

CN5: Pin Signal Pin Signal

1 Key-in Meter 11 Coin-Enable

2 Bill-in Meter 12 Bill-Enable

3 Coin-in Meter 13 Hopper-SSR

4 Pay-out Meter 14 GP0

5 Key-out Meter 15 GP1

6 Hand-pay Meter 1 16 GP2

7 Hand-pay Meter 2 17 GP3

8 Spare Meter 18 GP4

9 GND 19 GND

10 GND 20 GND

Note:

1. Each LAMP output supports open-drain 500mA (max) current; each Tower LAMP output supports open-drain 1A (max)

current.

2. Eight Meters support pulse-Generator function.

3. All output pin is open-drain circuit and operation maximum voltage cannot over +30V.

P/N：2200104-G

CN6/CN7 Gaming IO Input Connector (Micro-FIT 3.0mm 2*8 PINs)

CN6 Pin Signal Pin Signal

1 Button 12 9 Touch-Cal Key-Lock

2 Button 13 10 Spare Key-Lock

3 Button 14 11 Coin-In Signal A

4 Button 15 12 Coin-In Signal B

5 Button 16 13 Bill-In

6 Dissolve Key-Lock 14 Hopper Sensor

7 OM Key-Lock 15 GP0

8 Setup Key-Lock 16 GP1

CN7 Pin Signal Pin Signal

1 Door Switch 1 9 Button 4

2 Door Switch 2 10 Button 5

3 Door Switch 3 11 Button 6

4 Door Switch 4 12 Button 7

5 Door Switch 5 13 Button 8

6 Button 1 14 Button 9

7 Button 2 15 Button 10

8 Button 3 16 Button 11

Note:

1. All input pin logical high-level is +5V ~ +24V, logical low-level is 0V ~ +1.5V.

2. Coin-In Signal A, Coin-In Signal B, Bill-In, and Hopper Sensor support input counter fuction.

P/N：2200104-G

Appendix A

CN3 Output Signal TTL/RS232/RS485/cctalk Jumper Configuration

Default configuration of UART 5 and UART 6 are RS-232

Locations:

UART 5 Functions

RS-232:

TTL:

RS-485:

ccTalk:

Note: Orange block means shorted by a jumper, and others leave it N.C.

P/N：2200104-G

UART 6 Functions

RS-232:

TTL:

RS-485:

ccTalk:

Note: Orange block means shorted by a jumper, and others leave it N.C.

P/N：2200104-G

Appendix B AGC IO Definition

1. ACE-B7400 Gaming GPI:

Channel type Gaming I/O Remark

DI0 I Door SW1 AGA log 0

DI1 I Door SW2 AGA log 1

DI2 I Door SW3 AGA log 2

DI3 I Door SW4 AGA log 3

DI4 I Door SW5 AGA log 4

DI5 I AGA log 9 (onboard chassis switch, Door switch 6)

DI6 I AGA log 10 ( JST intrusion switch, Door switch 7)

DI7 I.I Button 1

DI8 I.I Button 2

DI9 I.I Button 3

DI10 I.I Button 4

DI11 I.I Button 5

DI12 I.I Button 6

DI13 I.I Button 7

DI14 I.I Button 8

DI15 I.I Button 9

DI16 I.I Button 10

DI17 I.I Button 11

DI18 I.I Button 12

DI19 I.I Button 13

DI20 I.I Button 14

DI21 I.I Button 15

DI22 I.I Button 16

DI23 I.I Dissolve Key-Lock (Key 1)

DI24 I.I OM Key-Lock (Key 2)

DI25 I.I

Setup Key-Lock(Hand Pay) (Key 3)

DI26 I.I Touch-Cal Key-Lock (Key 4)

DI27 I.I Spare Key-Lock (Key 5)

DI28 I.I Coin-In Signal A Counter 1

DI29 I.I Coin-In Signal B Counter 2

DI30 I.I Bill-In Counter 3

DI31 I.I Hopper Sensor Counter 4

DI32 I.I General Purpose

DI33 I.I General Purpose

P/N：2200104-G

2. ACE-B7400 Gaming GPO:

Channel type Gaming I/O Remark

DO0 O.C. Lamp1

DO1 O.C. Lamp2

DO2 O.C. Lamp3

DO3 O.C. Lamp4

DO4 O.C. Lamp5

DO5 O.C. Lamp6

DO6 O.C. Lamp7

DO7 O.C. Lamp8

DO8 O.C. Lamp9

DO9 O.C. Lamp10

DO10 O.C. Lamp11

DO11 O.C. Lamp12

DO12 O.C. Lamp13

DO13 O.C. Lamp14 1000 mA

DO14 O.C. Lamp15 1000 mA

DO15 O.C. Lamp16 1000 mA

DO16 O.C. Key-In Meter (Meter 1) Pulse Generator 1

DO17 O.C. Bill-In Meter (Meter 2) Pulse Generator 2

DO18 O.C. Coin-In Meter (Meter 3) Pulse Generator 3

DO19 O.C. Pay-Out Meter (Meter 4) Pulse Generator 4

DO20 O.C. Key-Out Meter (Meter 5) Pulse Generator 5

DO21 O.C. Hand-Pay Meter1 (Meter 6) Pulse Generator 6

DO22 O.C. Hand-Pay Meter2 (Meter 7) Pulse Generator 7

DO23 O.C. Spare Meter1 (Meter 8) Pulse Generator 8

DO24 O.C. Coin-Enable

DO25 O.C. Bill-Enable

DO26 O.C. Hopper SSR

DO27 O.C. General Purpose

DO28 O.C. General Purpose

DO29 O.C. General Purpose

DO30 O.C. General Purpose

DO31 O.C. General Purpose

P/N：2200104-G

3. ACE-B7400 Gaming Spare I/O:

Channel type Gaming I/O Remark

GPIO0 I/O Spare I/O bit 0

GPIO1 I/O Spare I/O bit 1

GPIO2 I/O Spare I/O bit 2

GPIO3 I/O Spare I/O bit 3

GPIO4 I/O Spare I/O bit 4

GPIO5 I/O Spare I/O bit 5

GPIO6 I/O Spare I/O bit 6

GPIO7 I/O Spare I/O bit 7

GPIO8 I/O Spare I/O bit 8

GPIO9 I/O Spare I/O bit 9

GPIO10 I/O Spare I/O bit 10

GPIO11 I/O Spare I/O bit 11

GPIO12 I/O Spare I/O bit 12

GPIO13 I/O Spare I/O bit 13

GPIO14 I/O Spare I/O bit 14

GPIO15 I/O Spare I/O bit 15

Andere Handbücher für ACE-B7400

Inhaltsverzeichnis

Andere Acrosser Technology Hauptplatine Handbücher

Acrosser Technology

Acrosser Technology AR-B1570 Bedienungsanleitung

Acrosser Technology

Acrosser Technology ACE-B7400 Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B1423 Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B1893CM6C Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B9012-G Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B1565 Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B1578 Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B6003 Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B5231ETCM1GZC Installationsanleitung

Acrosser Technology

Acrosser Technology AR-B5800A Installationsanleitung

Acrosser Technology

Acrosser Technology AR-B6005 Installationsanleitung

Acrosser Technology

Acrosser Technology AR-B1670 Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B8172 Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-ES0631ET Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B1622 Installationsanleitung

Acrosser Technology

Acrosser Technology AMB-IH61T3 Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B6051 Installationsanleitung

Acrosser Technology

Acrosser Technology AR-B1543 Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B1890 Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B5432 Bedienungsanleitung

Acrosser Technology

Acrosser Technology AMB-D255T3 Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B9891 Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B1991 Bedienungsanleitung

Acrosser Technology

Acrosser Technology AR-B2002 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung