ActionTec V.92 Bedienungsanleitung

V.92

PCI Pro Modem

User’s Manual

Table of Contents 1

0530-0277-000

I. Introduction 2

II. Contacting Actiontec Technical Support 3

III. Before You Begin 4

Product Features 4

Package Contents 5

IV. Installing the Modem 6

V. Installing the Modem Drivers 8

Configuring Windows 98, Windows 2000, Windows ME 8

Configuring Windows NT 4.0 9

Configuring Windows XP 10

VI. Installing Communications Software 12

Installing onWindows 98, NT, 2000, ME 12

Installing on Windows XP 16

VII. The Modem On Hold Feature 21

Installing the Modem On Hold Feature 21

Using the Modem On Hold Feature 24

VIII.Troubleshooting 26

AT Commands 27

IX. Notices 31

X. Safety Information 34

XI. Warranty 35

Proprietary Notice and Disclaimer

Unless otherwise noted, this document and the information herein disclosed are proprietary to Actiontec

Electronics, Inc the manufacturer. Any person or entity to whom this document is furnished or who other-

wise has possession thereof, by acceptance agrees that it will not be copied or reproduced in whole or in

part, nor used in any manner except to meet the purposes for which it was delivered.

The information in this document is sub ect to change without notice and should not be construed as a com-

mitment by Actiontec the manufacturer. Although Actiontec the manufacturer will make every effort to inform

users of substantive errors, Actiontec the manufacturer disclaims all liability for any loss or damage result-

ing from the use of this document or any hardware or software described herein, including without limitation

contingent, special or incidental liability.

Note: PC is a trademark of IBM Corporation. Windows 95, 98, ME, NT, 2000, XP are a trademarks of

Microsoft Inc. All other brand or product names and logos used in this manual are trademarks or registered

trademarks of their respective holders.

Table of Contents Page

Contacting Actiontec Technical Support

Introduction

Thank you for purchasing the Actiontec V.92 PCI Pro Modem. This modem is com-

patible to V.90 and K56Flex standard. The PCI Pro incorporates the latest technology

on controller-less V.92 modems for the PCI bus. With V.92 the user can benefit from

the following features:

Modem on Hold

Enables users to receive phone calls that will flash a Caller ID window, while

online. You can ignore the call while remaining online; or answer the call, put

theInternetsessions on hold if your ISP support this feature and you haveCall

Waiting service from the telco, then resume the online surfing after the

conversation.

Quick Connect

You will not have to wait all those frustrating minutes while the modem

connects to the web. Quick Connect memories the characteristics of your

phone lines, uses this information to reduce the next connection time.

V.44 Data Compression

With the V.44 technology, you will be able to browse the Internet and

download information faster.

Faster Upload Speeds

Upload speed may be increased to maximum of 48Kbps from 33.6Kbps

(depending on line condition).

Actiontec may have software feature updates from time to time, please check our web

siteat www.actiontec.com) forany new V.92 updates.Follow the instruction onthe web

to upgrade your modem to the latest firmware.

Introduction

Actiontec Electronics prides itself on making high-quality, durable, high-performance

products. If you should need assistance, the ActiontecTechnical Support Department is

available from 6am to 11pm (Mountain Time) Monday thru Sunday, to provide pro-

fessional support.

New drivers and firmware are released as need arises to insure maximum compatibility

and operation of your new Actiontec V.92 PCI Pro Modem.To find out more about this

and other Actiontec products, and to sign up for a free e-mail newsletter, visit the

Actiontec web site at: http://www.actiontec.com.

Contacting Actiontec Technical Support

Actiontec Electronics, Inc.

Technical Support

760 N. Mary Avenue

Sunnyvale, CA 94085

Phone: (719) 884-8300

Fax: (719) 522-9421

E-mail: techsupp actiontec.com

Before You BeginBefore You Begin

lll

Product Features

This V.92* PCI Pro Modem allows your computer to connect to an ISP supporting

V.92, V.90, or 56K Flex™ protocols.This manual describes the hardware and software

installation procedures for your new Actiontec V.92 PCI Pro Modem as well as trou-

bleshooting procedures.

Conforms to the ITU-T V.92 and V.90 specification with auto-negotiation of

V.44, V.42bis, V.34, V.32bis, V.32, V.23, V.22bis, V.22, V.21, Bell 212A, and

Bell 103 protocols.

Supports Group 3: class 1 fax protocols.

Supports V.80 video standard for videophone and video conferencing.

Controller-based modem with support for Windows 98, ME, NT, 2000 and XP.

Simple Plug-N-Play installation.

V.92 Features

The new V.44 compression standard provides better performance with faster

download and upload speeds. This means better data throughput which trans-

lates to faster web browsing and file downloading.

The modem-on-hold feature enables users to receive phone calls while connect-

ed to the internet. A window flashes with the Caller ID information allowing

the user to decide whether or not to take the call.

*The Actiontec V.92 PCI Pro Modem is capable of 56K downloads. However, due to FCC rules which restrict the

power output of your ISP’s modems, current download speeds are limited to 53K bps. Depending on the condi-

tions of your telephone lines, full 53Kbps connections may not be achieved. In these cases, you will achieve

speeds up to 53Kbps.

Before You Begin Package Contents

Actiontec V.92 PCI Pro Modem

User’s Manual

Data/Fax Data Communications Software

Telephone Cable (RJ-11)

Installation CD

Quick Start

Installing the Modem 7

Installing the Modem

For Windows 98, 2000, and ME you must install the driver first as shown

in Section 5 of this manual before installing the modem. ForWindows NT

and XP complete the hardware installation before installing the driver.

Follow this procedure to install the V.92 PCI Pro Modem into an open PCI slot inside

your computer.

1) Switch off the computer and all peripheral devices connected to it.

2) Unplug the computer power cord from the wall outlet.

3) Remove the computer’s cover. Refer to your computer owner’s manual for instruc-

tions.

4) CAUTION: Always discharge static electricity before handling your modem. You

may discharge static electricity by touching a grounded metal structure or by using

any commercially available grounding strap.

Make sure the expansion slot type is PCI, which has a smaller slot to fit the PCI

modem card. If you are not familiar with computers or computer hardware or you

cannot tell the difference between an ISA slot or PCI slot, obtain the help of some-

one who has a thorough understanding of computers. You will severely damage

your computer if you install the modem in the wrong slot.

5) Remove the screw securing the expansion slot cover behind one of the computer’s

available PCI expansion slots. Lift the expansion slot cover out as shown below.

Installing the Modem

Note: Make sure the slot is a

PCI slot. The card will fit

securely in a keyed PCI slot.

PCI slots are smaller than

ISA slots. PCI slots are light

colored and ISA slots are

dark colored.

7) Put the cover back on the computer and fasten.

8) Make sure that all power switches are in the OFF position, then reconnect the

power cables to the computer and its peripherals.

9) Unplug the telephone line cable from the telephone and connect it to the Line jack

as shown below.Then you can connect your telephone to the jack labeled “Phone”.

The position of the expansion slots in your computer may differ from the illustra-

tions shown in this user’s manual, depicting the slots in a vertical position.

Regardless of the position of the expansion slots, the installation steps remain the

same. Please refer to your computer owner’s manual for more information about

the expansion slot configuration of your computer.

6) Insert your ActiontecV.92 PCI Pro Modem into the available PCI expansion slot.

Then press on the top edge of the card, straight down until the card’s connectors

seat firmly in the PCI slot. Secure it with the screw removed in Step 5, as shown

below.

Installing The Modem DriversInstalling The Modem Drivers

Configuring Windows 98, Windows 2000, and Windows ME

1) Before installing the modem hardware, insert the CD-ROM provided with the

modem. The driver installation dialog box will appear. Click Install to begin the

driver installation.

Installing the Modem Drivers

2) Click OK in the dialog box to continue the driver installation.

3) Click OK to restart the computer and then follow the modem hardware installa-

tion instructions in Section 4.

2) Click OK in the dialog box to continue the driver installation.

3) Click OK to restart the computer.

Configuring Windows NT

1) After installing the modem hardware as shown in Section 4, insert the CD-ROM

provided with the modem. The driver installation dialog box will appear. Click

Install to begin the driver installation.

Installing The Modem Drivers

Installing The Modem Drivers 11

2) Click OK in the dialog box to continue the driver installation.

3) Click Continue Anyway in the Hardware Installation dialog box.Configuring Windows XP

1) After installing the modem hardware as shown in Section 4, insert the CD-ROM

provided with the modem. The driver installation dialog box will appear. Click

Install to begin the driver installation.

3) Click EXIT to complete the installation and close the application.

Installing the Communications Software 13

3) The “Source Directory” should be pointing to teh BitWare folder on your CD-

ROM drive. Input the “Destination Directory” where you would like the com-

munications software installed.. Click OK.

4) Input your user information and click OK.

Installing the Communications Software

Installing on Windows NT, 98, 2000, and ME

1) Insert the CD-ROM if you have not done so already and the BitWare

Communications Software will begin the installation process. Select “BitWare for

Windows Voice/Fax/Data 3.30.11” and click Install to continue.

Installing Communications Software

2) Click Accept to sccept the software license terms.

5) The installer will begin copying files to your hard drive.

Installing the Communications Software 15

9) Theinstallerwilldisplay the resultsof the modem detection. Inmost cases you will

not need to make any changes. Click Close to continue.

Installing the Communications Software

7) If you would like the installer to create independent Programs Icons click OK.

Otherwise click Cancel to skip this step.

10) Click OK to restart Windows and begin using the software.

6) Enter a name for the BitWare group window and click OK.

8) The installer will detect the Actiontec V.92 PCI Pro Modem.

1716

Installing the Communications Software

3) The “Source Directory” should be pointing to teh BitWare folder on your CD-

ROM drive. Input the “Destination Directory” where you would like the com-

munications software installed.. Click OK.

4) Input your user information and click OK.

Installing the Communications Software

Installing on Windows XP

1) Insert the CD-ROM if you have not done so already and the BitWare

Communications Software will begin the installation process. Select “BitWare for

Windows Voice/Fax/Data 3.30.11” and click Install to continue.

2) Click Accept to sccept the software license terms.

5) The installer will begin copying files to your hard drive.

Inhaltsverzeichnis

Andere ActionTec Modem Handbücher

ActionTec

ActionTec 1524 Bedienungsanleitung

ActionTec

ActionTec 56K/V.92 Bedienungsanleitung

ActionTec

ActionTec Q1000Qwest Bedienungsanleitung

ActionTec

ActionTec IS560LH Bedienungsanleitung

ActionTec

ActionTec GT724WGR Bedienungsanleitung

ActionTec

ActionTec External USB 56K Modem Bedienungsanleitung

ActionTec

ActionTec External 56K Call Waiting Bedienungsanleitung

ActionTec

ActionTec WirelessDSL Modem Bedienungsanleitung

ActionTec

ActionTec DeskTalk V.90 Bedienungsanleitung

ActionTec

ActionTec V.92 PCI Pro Modem 0530-0276-000 Bedienungsanleitung

ActionTec

ActionTec DataLink V.90 PC Card Fax Modem PCMCIA Bedienungsanleitung

ActionTec

ActionTec GT724R Handbuch

ActionTec

ActionTec GT724WGR Bedienungsanleitung

ActionTec

ActionTec GT784WN Bedienungsanleitung

ActionTec

ActionTec Plug n' Play Voice/Fax Modem V.90 ISA Bedienungsanleitung

ActionTec

ActionTec GT724R Bedienungsanleitung

ActionTec

ActionTec Actiontec USB/Ethernet DSL Modem with Routing Capabilities... Bedienungsanleitung

ActionTec

ActionTec GT701R Bedienungsanleitung

ActionTec

ActionTec DataLink V.90 PC Card Fax Modem PCMCIA Bedienungsanleitung

ActionTec

ActionTec External 56K Call Waiting Bedienungsanleitung

ActionTec

ActionTec GT701R Bedienungsanleitung

ActionTec

ActionTec 56K ISA Lite Bedienungsanleitung

ActionTec

ActionTec External 56K Call Waiting Bedienungsanleitung

ActionTec

ActionTec GT724WG Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung