Adam S3A Bedienungsanleitung

S3A Near-/Midfield Monitor

Operation manual / Bedienungsanleitung

English / deutsch

Introduction

Dear customer,

Congratulations on choosing an ADAM Audio S3A near- and mideld moni-

tor!

ADAM loudspeakers are built for maximum quality reproduction and audio

perfection. With the S3A you have selected a precise, high resolution speaker

system that allows you to professionally evaluate audio recordings. This mo-

nitor meets highest expectations in sound quality and craftmansship.

This manual is intended to provide you with information about your new

ADAM. It contains important information regarding safety, setting up,

handling, and warranty. We request that you read these sections carefully

to ensure an easy set up and to prevent potential problems.

The S3A is suitable for both near- and mideld monitoring. It is perfectly

suited for smaller and mid-sized control rooms, recording vehicles and post-

production suites—an ideal tool for situations where a combination of no-

compromise sound reproduction and a small footprint is required.

The S3A is a three-way ported active system that uses a single ART tweeter,

ensuring full compatibility with the latest expanded high frequency resolution

media formats, and two HexaCone©-bass/midrange drivers. One woofer acts

as a full-range driver with the second woofer joining it only below 150 Hz, an

approach that effectively doubles the area and power of the woofer when it

needs to respond to deeper frequencies. Each one of the three sections uses

an individual amp with continuous output of up to 150 Watts (RMS).

If you have any questions about this or any of our products, please don’t hesi-

tate to contact us–we will be happy to assist you in any possible way.

For detailed information concerning the ADAM technologies and products,

complete reviews, and a list of worldwide ADAM users and studios, please

visit our website:

www.adam-audio.com

We hope very much that you really enjoy your new loudspeakers, and wish

you many delightful hours with them.

The ADAM Audio Team

English

Table of contents

1. Quick Start .....................................4

1.1 Important Information ....................4

1.2 Quick Start S3A .............................4

2. Speaker Placement ........................5-7

2.1 General Recommendations ............5

2.2 Horizontal Setup ............................5

2.3 Stereo Setup ..................................6

2.4 Surround Setup ..............................7

2.5 Tweeter Height ...............................7

3. Controls/Speaker Adjustement .....8-9

3.1 The front (control) panel ................8

3.2 Input gain .......................................8

3.3 High gain ........................................8

3.4 High/low shelving ..........................9

3.5 LED ................................................9

4. Troubleshooting .............................10

5. Maintenance ..................................11

6. Transportation / Package ..............11

7. Environmental Information .............11

8. EU Declaration of Conformity ........12

9. Limited Warranty ............................13

9.1 Terms and Conditions ....................13

9.2 How to claim ..................................13

10. Safety Instructions .........................14

11 . Technical Data ...............................15

1. Quick Start

Important information for set up

Acclimation: After having unpacked your loudspeaker, please allow the sys-

tem to acclimate to the temperature of the room. Please do not connect the

speaker for approximately an hour.

HQ Cabling: We recommend using high quality cables to guarantee optimal

performance.

Solid stand: It is important to ensure the speakers stand rmly on a solid

ground!

Package: We recommend not to damage the package and to retain it. The

original packaging is the best guarantee for safe transportation (see 7.).

Break-in time: Please note that the loudspeakers will need a few days to

achieve optimum sonic performance.

Quick start S3A

Before connecting the loudspeakers to your audio components and the

power source make sure that both the loudspeakers and your audio system

is switched off!

Set all level controls fully counterclockwise.

Connect the loudspeakers with your audio units: Use a XLR cable. The male

plug goes into the loudspeaker, the female plug into your audio component.

Check if the specied voltage matches the voltage of the power supply

you use. If this is not the case do not connect the loudspeakers to a power

source! Please contact your local dealer or national distributor.

If the voltages match, connect the loudspeaker via the included power

cables to two AC sockets.

Switch on your audio system. Switch on the main on/off switches on the

back panel and nally the standby-switch on the front panel of the loud-

speakers.

Turn on your source of music and adjust the volume carefully.

1.2

1.1

English

2. Speaker Placement

General recommendations/advises

Direct sound ways: There should be no obstacles in the way from the monitor

to your ears. You should be able to see the speakers completely.

Distance to walls: The distance to the surrounding walls should be at least 40

cm to avoid early reections, which will degrade the sound.

Alignement: The loudspeakers should be aligned with the listener’s position.

Nearby objects: Please note that vibrating parts of nearby objects can mask

the sound.

Mechanical adjustements: If you plan to modify the speaker cabinet (e.g.

drilling holes), please contact us before doing so. Usually, we will handle your

warranty obliging.

Hoizontal set up (mirror symmetrical)

The S3A has been designed for a horizontal set up. Please note that there are

two different versions, A and B (see label on the rearside). The difference is

that the two woofers reproduce different frequency bands. One woofer acts

as a full-range driver with the second woofer joining it only below 150 Hz. The

A speaker has the woofer on the left side, the B unit on the right side. That

means that both woofer-midrange units should be on the inner side.

For a precise stereo immage it is necessary to use the speakers in a mirror

symmetrical set up.

Either this way:

Figure 1a: horizontal / mirror symmetrical set up

2.1

2.2

2. Speaker Placement

Or that way:

Figure 1b: horizontal / mirror symmetrical set up

You should not choose a set up like the folling examples:

Figure 2b: wrong set up

Stereo set up

If the loudspeaker is going to be used for stereo applications, the optimum

listening position should be located in the middle of a stereo triangle. This

means that your listening position will be located at the top of an imaginary

equilateral triangle and the two loudspeakers should be placed at the other

two points of this triangle.

2.3

Figure 3: Stereo Triangle

• both loudspeaker and the listening

spot should be a equilateral triangle

• approx. the same distances

between loudspeakers and the lou-

dspeakers / the listening spot

• alignment towards listening spot

English

2. Speaker Placement

Surround set up

Speaker positioning for multi-channel stereo purposes is ideally based on

a circle with speakers placed at 0° (Center), 30° (Front Right), 110° (Rear

Right), 250° (Rear Left), 330° (Front Left), with the listener being the circle’s

center (Radius between 0.7-2.0 m). This ITU recommended con guration may

vary depending on the purpose of the control room (music or  lm). However,

it is recommended to create a symmetrical listening position with the front

side and surround speaker pointing to the listener’s ear.

Figure 4: Surround set up

Tweeter at the height of ears

The Tweeter should be positioned approximately at the height of your ears. In

case you need to position the speaker in a signi cant lower or higher position,

the monitor should be angled accordingly.

Figure 5: Tweeter at height of ears / speaker angling

2.4

2.5

3. Controls/Speaker Adjustment

The front (control) panel

On the front you will nd a control panel that allows detailed ne-tuning of

your loudspeakers to your particular room acoustics and personal listening

preferences. The following tips are intended to assist you at using the con-

trols in the best manner.

Please note that using the controls may have a great impact on the overall

sound characteristics of your loudspeakers. We recommend using the con-

trols with utmost care and only after several audio tests with familiar record-

ings.

Input gain

‘Input Gain’ regulates the overall input sensitivity of your loudspeaker within

a range of -10 to +10 dB, and controls the volume of your loudspeaker equally

in all frequency ranges.

High gain

Whereas the ‘Input Gain’ raises or lowers the overall input sensitivity up to

+/-10 dB, the ‘High Gain’ works only within the frequency range of the tweet-

er (>1.800 Hz) only, raising or lowering up to +/-4 dB.

Figure 6:

Control panel

3.1

3.2

3.3

English

3. Controls/Speaker Adjustment

High / low shelving

The other two controls operate in a different manner. The ‘High Shelve’ is

a shelving lter that progressively raises or lowers above 6 kHz up to 6 dB.

Whereas the gains raise or lower a specic frequency range as a whole, the

shelve lters work differently. They do not alter a whole frequency band but

alter in this band, from a certain point (6 kHz respectively 150 Hz in this case)

the frequencies are gradually being changed (see gure 7 & 8).

LEDs

There are two diodes on the front panel. When the loudspeaker is being

switched on, the Overload-LED will ash red a few times. This does not indi-

cate an overload! It signalizes the control function of the protective circuit.

Afterwards, the On-LED will start to glow green, indicating power on. Only if

the Overload-LED ashes red during operation, it does indicate an overload.

Then, the protective circuit will be activated to prevent the speaker from

damage.

Figure 7

ROOM EQ >6 kHz for the high

frequencies above 6 kHz

Figure 8

ROOM EQ <150 Hz for the low

frequencies below 150 Hz

3.4

3.5

Figure 9: LEDs

LED, indicating power on

LED, ashes a few times red when loud-

speaker is being switched on. Flashing

during operation means overload.

4. Troubleshooting

All ADAM products are designed and manufactured to the highest quality

standards. However, if any problems with your speaker occur, we recommend

to proceed as follows:

Problem: The LED shows normal operation (green) but there is either no or

only a distorted audio signal.

If both (all) speakers are affected, the reason can probably be found within

the signal path. If only one speaker is affected, the problem will probably be

within this speaker.

Check the wiring

Is the cable defective? Are all cables connected correctly?

Check the signal path

Interchange the cables of both loudspeakers. Does the problem change with

one of the cables?

Connect the monitor as directly to the signal source as possible (please mind

the volume!). Is another part of the signal path (e.g. mixer, subwoofer) defec-

tive?

If the answer to all these question is ‘no’, the problem is being caused by the

loudspeaker with the utmost probability.

If the answer to at least one of these questions is ‘yes’, there will probably be

another defective device within the signal path.

Problem: You hear parasitic noises (like humming, buzzing, soughing, crack-

ing).

Please disconnect the signal cables.

If the noises disappear, check the signal path.

If the noises can still be heard, check for other electrical devices close to

the speakers (mobile phones, switching power supplies, etc.). If there is no

interfering device the speaker will probably cause the problem.

4.1

4.2

Inhaltsverzeichnis

Sprachen:

Andere Adam Sprecher Handbücher

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung