Adam S6X Bedienungsanleitung

S6X Main Monitor

Operation manual

English

S6X

Safety Instructions

Please read the following safety instructions before setting up your

system. Keep the instructions for subsequent reference. Please heed

the warnings and follow the instructions.

Caution: To reduce the risk of electric shock, do not open the loud-

speaker. There are no user-serviceable parts inside. Refer servicing to

qualied service personnel.

This product, as well as all attached extension cords, must be terminated

with an earth ground three-conductor AC mains power cord like the one

supplied with the product. To prevent shock hazard, all three components

must always be used.

Never replace any fuse with a value or type other than those specied.

Never bypass any fuse.

Always switch off your entire system before connecting or disconnecting

any cables, or when cleaning any components.

Do not place this unit on an ustable cart, stand or tripod, bracket or table.

The unit may fall, causing serious injury and/or serious damage. When cart

is used, use caution when moving the cart/apparatus combination.

Do not expose this product to rain or moisture, never wet the inside with

any liquid and never pour or spill liquids directly onto this unit. Please do

not ut any objects lled with liquids (e.g. vases, etc.) onto the speaker.

Check if the specied voltage matches the voltage of the power supply

you use. If this is not the case do not connect the loudspeakers to a power

source! Please contact your local dealer or national distributor.

$BVUJPO

3JTLPGFMFDUSJDBMTIPDL

%POPUPQFO

3JTRVFEFTIPDLFMFDUSJRVF

/FQBTPVWSJFS

$"65*0/503&%6$&5)&3*4,0''*3&03&-&$53*$4)0$,

%0/053&.07&#"$,$07&303"/:05)&31"35

/064&34&37*$"#-&1"354*/4*%&

%0/05&9104&5)*4&26*1.&/5503"*/03.0*4563&

3&'&34&37*$*/(5026"-*'*&%1&340//&-

English

Safety Instructions

Protect the cord from being walked on or pinched.

Always use fully checked cables. Defective cables can harm your speakers.

They are a common source for any kind of noise, hum, crackling etc.

Always keep electrical equipment out of the reach of children.

Always unplug sensitive electronic equipment during lightning storms.

The monitor should be installed near the socket outlet and disconnection of

the device should be easily accessible.

To completely disconnect from AC mains, disonnect the power supply from

the AC receptacle. Never use ammable or combustible chemicals for

cleaning audio components.

Avoid touching the speaker membranes and do not block the woofer’s

ventilation ports.

Never expose this product to extremely high or low temperatures. Never

operate this product in an explosive atmosphere.

High SPL’s may damage your hearing! Please do not get close to the

loudspeakers when using them at high volumes.

Please note that the diaphragms build up a magnetic eld. Do not ply with

magnetic items at close range to the diaphragms.

Assure free airow behind the speakers to maintain sufcient cooling.

Table of contents

Safety Instructions ......................2-3

1. Introduction ..................................5

2. Set up & Quick Start ....................6

2.1 Important Information for Set Up ...6

2.2 Quick Start .....................................6

3. Speaker Placement ......................7-8

3.1 General Recommendations ............7

3.2 Tweeter Height ...............................7

3.3 Stereo Setup ..................................8

3.4 Surround Setup ..............................8

4. Controls/Speaker Adjustement . 9-10

4.1 The front (control) panel ................9

4.2 Input Gain ......................................9

4.3 X-Curve Filter .................................9

4.4 Driver Gain .....................................10

4.5 High/Low Shelving ........................10

4.6 Bass EQ .........................................10

4.7 LED Dim .........................................10

5. Troubleshooting ...........................11

5.1 No or distorted Signal ....................11

5.2 Parasitic Noises .............................11

6. Maintenance .................................12

7. Transportation / Package ...........12

8. Environmental Information .........12

9. EU Declaration of Conformity .....13

10. Limited Warranty .........................14

10.1 Terms and Conditions ....................14

10.2 How to claim ..................................14

11. Technical Data ..............................15

English

1. Introduction

Dear customer,

Congratulations on choosing an ADAM Audio S6X monitor!

ADAM loudspeakers are built for maximum audio perfection. With the S6X

you have selected a precise, high resolution speaker system that allows

you to professionally evaluate audio recordings. This monitor meets highest

expectations in sound quality and craftmansship.

This manual is intended to provide you with information about your new

ADAM. It contains important information regarding safety, setting up,

handling, and warranty. We request that you read these sections carefully

to ensure an easy set up and to prevent potential problems.

S6X

The S6X is suitable for main monitoring. It is an ideal tool for no-compromise

sound reproduction in all larger environments.

The S6X is a four-way ported active system that uses the new X-ART tweeter

and midrange, ensuring full compatibility with the latest expanded high

frequency resolution media formats, and four HexaCone©-bass/midrange

drivers. Each one of the four cone drivers uses an individual PWM amp with

continuous output of up to 500 Watts for the subwoofers and for all other

drivers 250 Watts (RMS).

Questions? Problems?

If you have any questions about this or any of our products, please don’t

hesitate to contact us–we will be happy to assist you in any possible way.

For detailed information concerning the ADAM technologies and products,

complete reviews, and a list of worldwide ADAM users and studios, please

visit our website: www.adam-audio.com

We hope very much that you really enjoy your new loudspeakers, and wish

you many delightful hours with them.

The ADAM Audio Team

2. Information For Set Up / Quick Start

2.1 Important information for set up

Acclimation: After having unpacked your loudspeaker, please allow the

system to acclimate to the temperature of the room. Please do not connect

the speaker for approximately an hour.

HQ Cabling: We recommend using high quality cables to guarantee optimal

performance.

Solid stand: It is important to ensure the speakers stand rmly on a solid

ground!

Package: We recommend not to damage the package and to retain it. The

original packaging is the best guarantee for safe transportation (see 7.).

Break-in time: Please note that the loudspeakers will need a few days to

achieve optimum sonic performance.

2.2 Quick start S6X

Before connecting the loudspeakers to your audio components and the

power source make sure that both the loudspeakers and your audio system

is switched off!

Set all level controls fully counterclockwise. a.

Connect the loudspeakers with your audio units: b. Use a XLR cable. The male

plug goes into the loudspeaker, the female plug into your audio component.

Check if the specied voltage matches the voltage of the power supply c.

you use. If this is not the case do not connect the loudspeakers to a power

source! Please contact your local dealer or national distributor.

If the voltages match, connect the loudspeaker via the included power

cables to two AC sockets.

Switch on d. your audio system. Switch on the main on/off switches on

the back panel and nally the standby-switch on the front panel of the

loudspeakers.

Turn on your source of music and adjust the volume carefully.e.

English

3. Speaker Placement

3.1 General recommendations/advises

Direct sound ways: There should be no obstacles in the way from the

monitor to your ears. You should be able to see the speakers completely.

Distance to walls: The distance to the surrounding walls should be at least

40 cm to avoid early reections, which will degrade the sound.

Alignement: The loudspeakers should be aligned with the listener’s position.

Nearby objects: Please note that vibrating parts of nearby objects can

mask the sound.

Mechanical adjustements: If you plan to modify the speaker cabinet (e.g.

drilling holes), please contact us before doing so. Usually, we will handle

your warranty obliging.

3.2 Tweeter at the height of ears

The Tweeter should be positioned approximately at the height of your ears.

In case you need to position the speaker in a signicant lower or higher

position, the monitor should be angled accordingly.

Figure 1: Tweeter at height of ears / speaker angling

3. Speaker Placement

3.3 Stereo set up

If the loudspeaker is going to be used for stereo applications, the optimum

listening position should be located in the middle of a stereo triangle. This

means that your listening position will be located at the top of an imaginary

equilateral triangle and the two loudspeakers should be placed at the other

two points of this triangle.

3.4 Surround set up

Speaker positioning for multi-channel stereo purposes is ideally based

on a circle with speakers placed at 0° (Center), 30° (Front Right), 110°

(Rear Right), 250° (Rear Left), 330° (Front Left), with the listener being

the circle’s center (Radius between 0.7-2.0 m). This ITU recommended

conguration may vary depending on the purpose of the control room

(music or lm). However, it is recommended to create a symmetrical

listening position with the front side and surround speaker pointing to the

listener’s ear.

Figure 3: Surround set up

Figure 2: Stereo Triangle

• both loudspeaker and the listening spot

should be a equilateral triangle

• approx. the same distances between

loudspeakers and the loudspeakers / the

listening spot

• alignment towards listening spot

English

4. Controlpanel/Speaker Adjustment

4.1 The front (control) panel

On the front you will nd a new, highly sophisticated control panel that allows

detailed ne-tuning of your loudspeakers to your particular room acoustics

and personal listening preferences. The following tips are intended to assist

you at using the controls in the best manner.

Please note that using the controls may have a great impact on the overall

sound characteristics of your loudspeakers. We recommend using the

controls with utmost care and only after several audio tests with familiar

recordings.

4.2 Input gain

‘Input Gain’ regulates the overall input sensitivity of your loudspeaker within

a range of -10 to +10 dB, and controls the volume of your loudspeaker equally

in all frequency ranges.

4.3 X-Curve Filter

In large lm score mixing rooms, it may be desirable to have a representation

of the sound in the theatres. To meet the ISO 2969 Standard, the Dolby™ X-

curve has to be applied. The X-curve engages a 3 dB per octave roll-off above

2 kHz. The S6A Mk2 and S7A Mk2 have a switch located below the input

selector that activates this lter, eliminating the need for external processing

during the lm mix.

Figure 4: Control panel

4. Controlpanel/Speaker Adjustment

4.4 Driver gains

Whereas the ‘Input Gain’ raises or lowers the overall input sensitivity up to

+/-10 dB, the ‘Driver Gains’ work only within the corresponding frequency

range, raising or lowering from +/-2 to +/-6 dB.

4.5 High / low shelving

The other two controls operate in a different manner. The ‘High Shelve’ is

a shelving lter that progressively raises or lowers above 6 kHz up to 6 dB.

Whereas the gains raise or lower a specic frequency range as a whole, the

shelve lters work differently. They do not alter a whole frequency band but

alter in this band, from a certain point (6 kHz respectively 150 Hz in this case)

the frequencies are gradually being changed (see gure 5 & 6).

4.6 Bass EQ Section (parametric EQ)

There are three fully parametric EQs (20 Hz to 200 Hz) that

can be used to combat standing waves in the control room.

The EQs can be bypassed individually or as a group so that

their overall effect can be analyzed in direct comparison to

the unaffected signal.

4.7 LED Dim

All LED indicators can be dimmed if necessary by pressing the ‘LED Dim’-

button.

Figure 5: ROOM EQ >6 kHz for the high

frequencies above 6 kHz

Figure 6: ROOM EQ <150 Hz for the low

frequencies below 150 Hz

Andere Handbücher für S6X

Inhaltsverzeichnis

Andere Adam Sprecher Handbücher

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung