Adaptec 39320D Bedienungsanleitung

Adaptec SCSI Card 39320D

User’s Guide

For Floppy Disks (OEM)

reproduced, stored in a retrieval system, or transmitted in any form or by any

means, electronic, mechanical, photocopying, recording or otherwise, without the

prior written consent of Adaptec, Inc., 691 South Milpitas Blvd., Milpitas, CA 95035.

Trademarks

Adaptec, the Adaptec logo, AHA, AIC, EZ-SCSI, and SCSISelect are trademarks of

Adaptec, Inc., which may be registered in some jurisdictions.

Windows NT, Windows 2000, and Windows XP, are trademarks of Microsoft

Corporation in the US and other countries, used under license.

All other trademarks are the property of their respective owners.

Changes

The material in this document is for information only and is subject to change

without notice. While reasonable efforts have been made in the preparation of this

document to assure its accuracy, Adaptec, Inc. assumes no liability resulting from

errors or omissions in this document, or from the use of the information contained

herein.

Adaptec reserves the right to make changes in the product design without

reservation and without notification to its users.

Disclaimer

IF THIS PRODUCT DIRECTS YOU TO COPY MATERIALS, YOU MUST HAVE

PERMISSION FROM THE COPYRIGHT OWNER OF THE MATERIALS TO

AVOID VIOLATING THE LAW WHICH COULD RESULT IN DAMAGES OR

OTHER REMEDIES.

iii

Contents

1 Introduction

Ultra320 SCSI on the Adaptec SCSI Card 39320D 1-1

Device Drivers 1-3

Operating Systems 1-3

System Requirements 1-4

Understanding SCSI 1-4

SCSI IDs 1-5

Terminating the SCSI Bus 1-6

2 Using the Adaptec SCSI Card 39320D and SCSI

Devices

Using SCSI Devices 2-2

Using SCSI Hard Disk Drives 2-2

Using Ultra320/160 Hard Disk Drives 2-2

Using SCSI Devices 2-3

Combining SCSI and Non-SCSI Devices 2-3

Installing Multiple SCSI Cards 2-4

Connecting the LED Connector 2-5

Overriding SCSI Termination Settings 2-6

Connecting SCSI Devices 2-7

Maximum Cable Lengths 2-9

3 Configuring the Adaptec SCSI Card 39320D with

SCSISelect

Starting SCSISelect 3-3

Exiting SCSISelect 3-3

Using SCSISelect Settings 3-4

SCSI Bus Interface Options 3-4

Boot Device Configuration – Non-BBS Systems Only 3-5

SCSI Device Configuration Options 3-5

Advanced Configuration Options 3-7

Changing Configuration Settings 3-10

Adaptec SCSI Card 39320D User’s Guide for Floppy Disks (OEM)

Using SCSI Disk Utilities 3-15

Listing SCSI IDs and LUNs 3-15

Verifying or Formatting a Disk 3-16

4 Installing Windows 2000

Installing the Driver When Installing Windows 2000 4-2

Updating the Driver When Windows 2000 is Already

Installed 4-3

Upgrading a Windows NT 4.0 Installation to

Windows 2000 4-4

Using Advanced Configuration Parameters 4-4

Using Windows 2000 SCSI Parameters 4-4

Using Driver-specific Parameters 4-6

InstallingaNewHostAdapterafterWindows 2000IsAlready

Installed 4-8

Removing a Host Adapter 4-8

Swapping a Host Adapter 4-9

Troubleshooting 4-10

Problems and Solutions 4-10

Error Messages 4-11

Driver Error Messages 4-12

5 Installing Windows NT 4.0

Installing the Driver When Installing Windows NT 5-2

Completing a Fresh Windows NT 4.0 Installation From

Floppy Disk 5-2

Completing a Fresh Windows NT 4.0 Installation From

CD 5-3

Installing the Driver When Windows NT 4.0 is Already

Installed 5-4

Updating Windows NT 4.0 5-4

Using Advanced Configuration Parameters 5-5

Using Windows NT 4.0 SCSI Parameters 5-5

Using Driver-specific Parameters 5-7

Hot-Plug PCI Support 5-8

Using Windows NT 4.0 and the Host Adapter 5-9

Removing a Host Adapter 5-9

Contents

Removing a Host Adapter in Windows NT

4.0 5-10

Swapping a Host Adapter 5-11

Troubleshooting 5-12

Problems and Solutions 5-12

Error Messages 5-14

adpu320.sys Error Messages 5-15

6 Installing Windows XP

Installing the Driver When Installing Windows XP 6-2

Installing Windows XP (32-bit) 6-2

Installing Windows XP (64-bit) 6-3

Installing a New Host Adapter after Windows XP is Already

Installed 6-4

Using Advanced Configuration Parameters 6-5

Using Windows XP SCSI Parameters 6-5

Using Driver-Specific Parameters 6-7

Removing a Host Adapter 6-8

Swapping a Host Adapter 6-9

Troubleshooting 6-10

Problems and Solutions 6-10

Error Messages 6-11

Driver Error Messages 6-12

7 Installing Novell NetWare

Installing the Driver When Installing NetWare 7-2

NetWare 4.2 7-2

NetWare 5.0 7-3

NetWare 5.1 and 6.0 7-3

Installing the Driver When NetWare is Already Installed 7-4

Loading the Driver at Server Bootup 7-5

Using the Load Command Line Options 7-6

adpu320.ham Command Line Options 7-6

Bit Mask Options 7-7

Sample Load Commands 7-7

Using NetWare and the Host Adapter 7-8

Using Removable Media 7-8

Adaptec SCSI Card 39320D for Floppy Disks User’s Guide (OEM)

Mount Status 7-9

Lock Status 7-9

Using the NetWare Tape Backup 7-9

Using a CD with NetWare 7-10

Netware 4.2 7-10

NetWare 5.x and 6.0 7-11

Optimizing Performance 7-11

Troubleshooting 7-12

Error Messages 7-12

8 Installing UnixWare and Open Unix

Installing the Driver When Installing UnixWare/Open Unix

8-2

Installing the Driver When UnixWare/Open Unix is Already

Installed 8-3

Back Up the Kernel 8-4

Load the Package 8-4

Modify the New System File 8-5

Rebuild the UnixWare/Open Unix Kernel 8-5

Boot the New Kernel 8-6

Using UnixWare/Open Unix and the Host Adapter 8-7

Using Tunable Parameters 8-7

Using Multiple Host Adapters 8-7

Removing the Driver 8-8

Troubleshooting 8-9

Problems and Solutions 8-9

Error Messages 8-10

9 Installing Sun Solaris

Installing the driver when installing Solaris 8 9-1

Installing the Driver when Solaris 8 is Already Installed 9-3

Removing the Driver From Solaris 8 9-4

Command Line Options 9-5

Additional Notes 9-5

Known/Unresolved or FYI Issues 9-5

vii

Contents

10 Installing Linux

Installing the Device Drivers for Red Hat Linux 10-1

Installing the Device Drivers for SuSE Linux 10-3

A Troubleshooting in Windows

Troubleshooting Checklist A-1

General Troubleshooting A-2

Troubleshooting in Windows NT 4.0 A-5

Common Error Messages A-5

Index

1-1

Introduction

In this Chapter

Ultra320 SCSI on the Adaptec SCSI Card

39320D

The Adaptec SCSI Card 39320D enables you to connect up to 30

SCSI devices—such as very large arrays of high-performance hard

disk drives, external storage subsystems, Ultra320/160, or Ultra2

hard disk drives, scanners, and CD-ROM drives—to any Intel-

based computer with 64- or 32-bit PCI/PCI-X expansion slots.

Ultra320 is an enhanced SCSI technology that transfers data at up

to 320 MB/sec. Ultra320 SCSI allows cable length of up to 12

meters for optimal connectivity and flexibility.1

Ultra320 SCSI on the Adaptec SCSI Card 39320D 1-1

Device Drivers 1-3

Operating Systems 1-3

System Requirements 1-4

Understanding SCSI 1-4

SCSI IDs 1-5

Terminating the SCSI Bus 1-6

1When only one Ultra320/Ultra160, or Ultra2 SCSI device is connected, the

cable length can be up to 25 meters (82 feet).

1-2

Adaptec SCSI Card 39320D User’s Guide for Floppy Disks (OEM)

The Adaptec SCSI Card 39320D has two independent SCSI

channels, each with a maximum throughput of 320 MB/sec.

■SCSI Channel A—(marked CH A on the card) has one internal

connector and one external connector.

■SCSI Channel B—(marked CH B on the card) has one external

connector.

For the bestdata I/Operformance, connectonly LVD (Low Voltage

Differential) devices and LVD cables to the Adaptec SCSI Card

39320D. (LVD devices means Ultra 320, Ultra160, and Ultra2 SCSI

devices.) If you connect non-LVD devices (for example, Fast SCSI

or Ultra SCSI devices), we recommend that you connect them to

SCSI Channel B. This allows you to operate LVD SCSI devices at

their maximum speed on Channel Awhile at the same time using

non-LVD SCSI devices on Channel B.

Althoughthe Adaptec SCSI Card 39320D isa 64-bit PCIcard, italso

works in a 32-bit PCI slot. When installed in a 32-bit PCI slot, the

card automatically runs in the slower 32-bit mode.

This User’s Guide provides information about using the Adaptec

SCSI Card 39320D and SCSI devices, troubleshooting, SCSI

termination, and other important topics. It explains how to use the

built-in SCSISelect®utility if you need to change the Adaptec SCSI

Card 39320D settings. It also explains how to install the software

device drivers for your operating system.

Note: Read the Adaptec SCSI Card 39320D Installation Guide if

you need instructions on installing the SCSI Card and

connecting SCSI devices to it.

1-3

Introduction

Device Drivers

The Adaptec SCSI Card 39320D comes with aset of softwaredevice

drivers and other files that enable it to communicate with your

computer. The following table lists the correct driver for your

operating system.

For information on how to install the driver for the Adaptec SCSI

Card39320D, refer tothe section of this User’s Guide that describes

your specific operating system.

Operating Systems

The Adaptec SCSI Card 39320D supports these operating systems:

■Windows NT®4.0

■Windows®2000

■Windows®XP

■Novell NetWare 6.0

■Caldera Open Unix 8

■SCO UnixWare 7.11

■Sun Solaris 8

Operating System Ultra320 Driver

Windows NT 4.0 adpu320.sys

Windows 2000 adpu320.sys

Windows XP adpu320.sys

NetWare adpu320.ham

SCO UnixWare adpu320

Caldera Open

Unix adpu320

Solaris ADPU320

Inhaltsverzeichnis

Andere Adaptec Controller Handbücher

Adaptec

Adaptec ICP 5045BL Bedienungsanleitung

Adaptec

Adaptec AIC-6915 Bedienungs- und Wartungshandbuch

Adaptec

Adaptec 39160 Bedienungsanleitung

Adaptec

Adaptec ASR-5085 Handbuch

Adaptec

Adaptec 44300 Bedienungsanleitung

Adaptec

Adaptec 2025ZCR - SCSI RAID Storage Controller Bedienungsanleitung

Adaptec

Adaptec 29160LP - SCSI Card Storage Controller U160 160... Bedienungsanleitung

Adaptec

Adaptec ACB-4525Z Bedienungsanleitung

Adaptec

Adaptec 9803 Benutzerhandbuch

Adaptec

Adaptec 1405 Bedienungsanleitung

Adaptec

Adaptec AEC-4412B Bedienungsanleitung

Adaptec

Adaptec ACB-2071 Bedienungsanleitung

Adaptec

Adaptec 2120S - SCSI RAID Controller Bedienungsanleitung

Adaptec

Adaptec OnTarget Bedienungsanleitung

Adaptec

Adaptec GDT6110 Bedienungsanleitung

Adaptec

Adaptec ASR-3085 Betriebsanleitung

Adaptec

Adaptec ADS-7210 Gebrauchs- und Pflegehandbuch

Adaptec

Adaptec AAR-2420SA Merkblatt

Adaptec

Adaptec 2120S - SCSI RAID Controller Bedienungsanleitung

Adaptec

Adaptec ASR-2045 Betriebsanleitung

Adaptec

Adaptec ACB-2002A Bedienungsanleitung

Adaptec

Adaptec AAR-1420SA Merkblatt

Adaptec

Adaptec 1420SA - Serial ATA II RAID Controller Bedienungsanleitung

Adaptec

Adaptec RAID 5805Z Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung