Adastra BC5A Bedienungsanleitung
BC5A / BC6A
ACTIVE STEREO SPEAKER SET
Order ref: 170.164UK, 170.165UK, 170.166UK, 170.168UK, 170.169UK
User Manual
Active + satellite stereo pair
Supplied with adjustable wall brackets
Supplied with satellite link cable
RCA or 3.5mm stereo inputs
BC5A BC6A User Manual
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
Introduction
Thank you for choosing the BC-series active speaker set. Please read this manual prior to use to avoid
damage to the item. These compact, self-contained stereo speaker sets are designed to deliver high quality
near-field or perimeter coverage for various monitoring and installed sound applications
Contents
Please take care when unpacking this product. Inspect for any damage and ensure you have the following
components…
BC-series active speaker with built-in amplifier
BC-series passive satellite speaker
2 x wall-mounting brackets with screw caps
Satellite speaker wire –modular connector
Mains lead(s)
Safety Conventions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE NE
PAS OUVRIR
This symbol indicates that dangerous voltage constituting a risk of electric shock is
present within this unit
This symbol indicates that there are important operating and maintenance instructions
in the literature accompanying this unit.
Warning
To prevent the risk of fire or electric shock, do not expose this appliance to rain or moisture.
To prevent electric shock do not remove the rear cover.
No user serviceable parts inside. Refer servicing to qualified service personnel.
Safety
Prior to connecting the dc adaptor to mains, ensure that the supply voltage is correct.
Avoid ingress of water or particles into the enclosure.
Placement
Keep the unit out of direct sunlight and away from heat sources.
Keep the unit away from moisture or dusty environments.
Allow adequate space for cooling at the rear of the active speaker unit
Cleaning
Use a soft cloth with a neutral detergent to clean the cabinet, panel and controls. Do not use solvents.
BC5A BC6A User Manual
Panel layout
(example shown is BC5A)
Setting up
For near-field or desktop use, space speakers apart for adequate stereo separation depending on
proximity to the listener. For installations using the supplied wall-mount brackets, attach the brackets
to a solid surface using fixings which are sufficient to hold the weight of the active speaker. Take
care to mount the active unit close enough to a mains outlet for the supplied adaptor to reach.
Fix the speaker units to the brackets at top and bottom using the supplied screw caps. Each can be
rotated to aim the general direction of sound output.
If the speakers are mounted at height or where falling objects may be hazardous, it is advised to
attach a secondary means of support (e.g. drop-wire or chain)
Operation
Link the powered speaker to the satellite using the supplied modular connector speaker lead (5)
With the rotary VOLUME (4) control set to minimum and TREBLE and BASS controls set to the
vertical (12 o’clock) position, connect the supplied mains lead to the rear of the active unit (2) and
plug into a suitable mains outlet. Connect the source signal into the active unit via either L+R RCA
connectors or 3.5mm stereo jack input (8, 9). Switch the power on (3) and gradually turn the rotary
VOLUME control clockwise and increase volume level to the required amount.
The stereo/mono switch (6) offers mono output for both speakers if required. Stereo is default.
Adjust TREBLE (7) and BASS (10) controls to provide the desired tonal response.
The centre position is unaffected, to the left is cut and to the right is boost.
Turn down rotary VOLUME control before switching off.
1
Fuse holder
2
Mains inlet (Fig.8 BC5A, IEC BC6A)
3
Power on/off switch
4
Rotary VOLUME control
5
Satellite speaker output
6
Stereo/mono switch
7
Rotary TREBLE tone control
8
3.5mm stereo line input
9
L+R RCA line input
10
Rotary BASS tone control
BC5A BC6A User Manual
Specifications
Model
BC5A
BC6A
Power supply
230Vac, 50Hz (fig 8)
230Vac, 50Hz (IEC)
Woofer
133mmØ (5.25") PP cone
165mmØ (6.5") PP cone
Tweeter
25mm balanced dome
Power output max
2 x 30W
2 x 50W
Controls
Volume, Treble, Bass, Stereo/Mono, Power on/off
Input connections
3.5mm stereo and L+R RCA
Frequency response
100Hz - 20kHz
80Hz - 20kHz
Dispersion
150° (-3dB)
Dimensions (each)
240 x 178 x 170mm
288 x 215 x 193mm
Troubleshooting
No output and Power LED not lit
Check power switch is not set to “Off”
Check mains adapter is connected and in good condition
Check mains fuse. Refer to qualified engineer if blown.
Check mains outlet is on
Power LED lit but no output
Turn up rotary VOLUME, TREBLE and BASS controls
Check signal lead is connected properly
Check sound source is playing
Sound output only from one
speaker
Check wire is connected from active to satellite properly
Try stereo/mono switch to check if signal is only one side
Check signal lead is connected properly
Output is very low
Turn up rotary VOLUME control
Check sound source is turned up
Output is too loud or distorted
Turn down rotary VOLUME control
Check sound source output is not too high for input
Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed as Electrical or
Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life.
The goods must be disposed of according to your local council guidelines.
Errors and omissions excepted.
Copyright© 2015. AVSL Group Ltd.
Inhaltsverzeichnis
Andere Adastra Lautsprechersystem Handbücher
Beliebte Lautsprechersystem Handbücher anderer Marken
Sondpex
Sondpex Active Speaker System and Digital Music... Bedienungsanleitung
JVC
JVC NX-PN7 Bedienungsanleitung
Marshall Amplification
Marshall Amplification AR-DM61-BT Bedienungsanleitung
Yamaha
Yamaha NX-A01 - Speaker Sys Bedienungsanleitung
SE Audiotechnik
SE Audiotechnik I-LINE Bedienungsanleitung
Gemini
Gemini WRX-843 Series Bedienungsanleitung