ADB ACE2 Bedienungsanleitung

www.adb-air.com

Airfield Lighting

Product Solutions Catalog

Operation ManualOperation Manual

Advanced Control

Equipment (ACE2)

96A0357, Rev. F, 7/18/16

Advanced Control Equipment (ACE2)

96A0357 Rev. F

DISCLAIMER / WARRANTY

A.0 Disclaimer /

Standard Warranty

A.1 CE certification The equipment listed as CE certified means that the product complies with the essential requirements

concerning safety and hygiene. The directives that have been taken into consideration in the design are

available on written request to ADB.

A.2 ETL certification The equipment listed as ETL certified means that the product complies with the essential requirements

concerning safety and FAA Airfield regulations. The directives that have been taken into consideration in

the design are available on written request to ADB.

A.3 LED Product

Guarantee

Where applicable, per FAA EB67(applicable edition), ADB L858(L) Airfield Guidance Signs are warranted

against electrical defects in design or manufacture of the LED or LED specific circuitry for a period of 4

years. ADB LED light fixtures (with the exception of obstruction lighting) are warranted against

mechanical and physical defects in design or manufacture for a period of 12 months from date of

installation; and are warranted against electrical defects in design or manufacture of the LED or LED

specific circuitry for a period of 4 years per FAA EB67 (applicable edition).

NOTE: See your sales order contract for a complete warranty description. In some specific cases,

deviations are (to be) accepted in the contract, which will supersede the standard warranty.

A.4 Standard Product

Guarantee

Products of ADB manufacture are guaranteed against mechanical, electrical, and physical defects

(excluding lamps) which may occur during proper and normal use for a period of one year from the date

of installation or 2 years from date of shipment and are guaranteed to be merchantable and fit for the

ordinary purposes for which such products are made. ADB L858 Airfield Guidance Signs are warranted

against mechanical and physical defects in design or manufacture for a period of 2 years from date of

installation per FAA AC 150/5345-44 (applicable edition).

NOTE: See your sales order contract for a complete warranty description.

A.5 All Products LED Products of ADB, manufactured and sold by ADB or its licensed representatives, meets the

corresponding requirements of FAA, ICAO and IEC.

ADB will correct by repair or replacement per the applicable guarantee above, at its option, equipment or

parts which fail because of mechanical, electrical or physical defects, provided that the goods have been

properly handled and stored prior to installation, properly installed and properly operated after installation,

and provided further that Buyer gives ADB Airfield Solutions written notice of such defects after delivery of

the goods to Buyer. Refer to the Safety section for more information on Material Handling Precautions

and Storage precautions that must be followed.

ADB reserves the right to examine goods upon which a claim is made. Said goods must be presented in

the same condition as when the defect therein was discovered. ADB Airfield Solutions furthers reserves

the right to require the return of such goods to establish any claim.

ADB’s obligation under this guarantee is limited to making repair or replacement within a reasonable time

after receipt of such written notice and does not include any other costs such as the cost of removal of

defective part, installation of repaired product, labor or consequential damages of any kind, the exclusive

remedy being to require such new parts to be furnished.

ADB’s liability under no circumstances will exceed the contract price of goods claimed to be defective.

Any returns under this guarantee are to be on a transportation charges prepaid basis. For products not

manufactured by, but sold by ADB Airfield Solutions, warranty is limited to that extended by the original

manufacturer.

This is ADB’s sole guarantee and warranty with respect to the goods; there are no express warranties or

warranties of fitness for any particular purpose or any implied warranties of fitness for any particular

purpose or any implied warranties other than those made expressly herein. All such warranties being

expressly disclaimed.

Advanced Control Equipment (ACE2)

96A0357 Rev. F

DISCLAIMER / WARRANTY

A.6 Liability

ADB cannot be held responsible for injuries or damages resulting from non-standard, unintended uses of

its equipment. The equipment is designed and intended only for the purpose described in the manual.

Uses not described in the manual are considered unintended uses and may result in serious personal

injury, death or property damage.

Unintended uses includes the following actions:

— Making changes to equipment that have not been recommended or described in this manual or

using parts that are not genuine ADB replacement parts or accessories.

— Failing to make sure that auxiliary equipment complies with approval agency requirements, local

codes, and all applicable safety standards if not in contradiction with the general rules.

— Using materials or auxiliary equipment that are inappropriate or incompatible with your ADB

equipment.

— Allowing unskilled personnel to perform any task on or with the equipment.

WARNING

Use of the equipment in ways other than described in the catalogue leaflet and the manual may result in personal

injury, death, or property and equipment damage. Use this equipment only as described in the manual.

Advanced Control Equipment (ACE2)

96A0357 Rev. F

DISCLAIMER / WARRANTY

A.7 © ADB BVBA This manual or parts thereof may not be reproduced, stored in a retrieval system, or transmitted, in any

form or by any means, electronic, mechanical, photocopying, recording, nor otherwise, without ADB

BVBA’s prior written consent.

This manual could contain technical inaccuracies or typographical errors. ADB BVBA reserves the right to

revise this manual from time to time in the contents thereof without obligation of ADB BVBA to notify any

person of such revision or change. Details and values given in this manual are average values and have

been compiled with care. They are not binding, however, and ADB BVBA disclaims any liability for

damages or detriments suffered as a result of reliance on the information given herein or the use of

products, processes or equipment to which this manual refers. No warranty is made that the use of the

information or of the products, processes or equipment to which this manual refers will not infringe any

third party’s patents or rights. The information given does not release the buyer from making their own

experiments and tests.

TABLE OF CONTENTS

Advanced Control Equipment (ACE2) ......................................................................... i

A.0: Disclaimer / Standard Warranty ........................................................................ II

A.1 :CE certification ..................................................................................................... ii

A.2 :ETL certification ................................................................................................... ii

A.3 :LED Product Guarantee ...................................................................................... ii

A.4 :Standard Product Guarantee ............................................................................... ii

A.5 :All Products .......................................................................................................... ii

A.6 :Liability .................................................................................................................iii

A.7 :© ADB BVBA ...................................................................................................... iv

1.0: Safety ................................................................................................................... 1

1.1 :HAZARD Icons used in the manual .....................................................................1

1.1.1 :Qualified Personnel .....................................................................................1

1.2 :To use this equipment safely: .............................................................................. 2

1.2.1 :Additional Reference Materials: ...................................................................2

1.2.2 :Intended Use ............................................................................................... 2

1.2.3 :Fasteners .....................................................................................................2

1.2.4 :Operation ..................................................................................................... 3

1.2.5 :Storage ........................................................................................................3

1.2.6 :Material Handling Precautions ..................................................................... 3

1.2.7 :Action in the Event of a System or Component Malfunction .......................4

1.2.8 :Maintenance ................................................................................................ 4

1.2.9 :Maintenance and Repair ............................................................................. 4

2.0: Advanced Control Equipment ...........................................................................5

2.1 :About this manual ................................................................................................ 5

2.1.1 :How to work with the manual ....................................................................... 5

2.1.2 :Record of changes ...................................................................................... 5

2.2 :Introduction ..........................................................................................................6

2.2.1 :Dimensions ..................................................................................................6

2.2.2 :Wall Mount ................................................................................................... 6

2.2.3 :Internal-Mount .............................................................................................7

2.2.4 :Combo Box-Mount ....................................................................................... 8

2.2.5 :Main Circuit Board .......................................................................................9

2.2.6 :ACE2 Lamps-Out Monitoring Board .......................................................... 11

2.2.7 :Theory of Operation ...................................................................................12

2.2.8 :Communication .......................................................................................... 13

2.2.9 :Modes of Operation ...................................................................................14

2.2.9.1 :Stand-Alone Configuration................................................................ 14

2.2.10 :Stand-Alone Pushbutton Description ....................................................... 17

2.2.11 :I/O Status display .................................................................................... 19

2.2.11.1 :Lamps-Out Calibration for Stand-Alone Mode ................................ 19

2.3 :Installation ......................................................................................................... 20

2.3.1 :Introduction ................................................................................................ 20

2.3.2 :Wall-Mount Installation .............................................................................. 20

2.3.2.1 :ACE2 Cabling Entry.......................................................................... 21

2.3.3 :Internal-Mount Installation ......................................................................... 24

2.3.4 :Combo Box-Mount Installation .................................................................. 25

2.3.4.1 :ACE2 Cable Entry............................................................................. 27

2.4 :Troubleshooting ................................................................................................. 30

2.4.1 :Troubleshooting Procedures .....................................................................30

2.4.2 :Error Messages ......................................................................................... 32

2.5 :Parts ................................................................................................................... 35

2.5.1 :Parts List ....................................................................................................36

2.6 :Wiring Schematics ............................................................................................. 37

2.6.1 :Connectors ................................................................................................ 37

Advanced Control Equipment (ACE2)

96A0357 Rev. F

1.0 Safety This section contains general safety instructions for installing and using ADB Airfield

Solutions equipment. Some safety instructions may not apply to the equipment in this

manual. Task- and equipment-specific warnings are included in other sections of this manual

where appropriate.

1.1 HAZARD Icons

used in the manual

For all HAZARD symbols in use, see the Safety section. All symbols must comply with ISO

and ANSI standards.

Carefully read and observe all safety instructions in this manual, which alert you to safety

hazards and conditions that may result in personal injury, death or property and equipment

damage and are accompanied by the symbol shown below.

1.1.1 Qualified Personnel

WARNING

• Failure to observe a warning may result in personal injury, death or equipment damage.

DANGER - RISK OF ELECTRICAL SHOCK OR ARC FLASH

• Disconnect equipment from line voltage. Failure to observe this warning may result in

personal injury, death, or equipment damage. ARC Flash may cause blindness, severe

burns or death.

WARNING - WEAR PERSONAL PROTECTIVE EQUIPMENT

• Failure to observe may result in serious injury.

WARNING - DO NOT TOUCH

• Failure to observe this warning may result in personal injury, death, or equipment

damage.

CAUTION

• Failure to observe a caution may result in equipment damage.

IMPORTANT INFORMATION

The term qualified personnel is defined here as individuals who thoroughly understand the equipment and its safe

operation, maintenance and repair. Qualified personnel are physically capable of performing the required tasks,

familiar with all relevant safety rules and regulations and have been trained to safely install, operate, maintain and

repair the equipment. It is the responsibility of the company operating this equipment to ensure that its personnel meet

these requirements.

Always use required personal protective equipment (PPE) and follow safe electrical work practices.

Advanced Control Equipment (ACE2)

96A0357 Rev. F

To use this equipment safely:

1.2 To use this

equipment safely:

1.2.1 Additional Reference

Materials:

1.2.2 Intended Use

1.2.3 Fasteners

WARNING

Read installation instructions in their entirety before starting installation.

• Become familiar with the general safety instructions in this section of the manual before installing, operating,

maintaining or repairing this equipment.

• Read and carefully follow the instructions throughout this manual for performing specific tasks and working with

specific equipment.

• Make this manual available to personnel installing, operating, maintaining or repairing this equipment.

• Follow all applicable safety procedures required by your company, industry standards and government or other

regulatory agencies.

• Install all electrical connections to local code.

• Use only electrical wire of sufficient gauge and insulation to handle the rated current demand. All wiring must meet

local codes.

• Route electrical wiring along a protected path. Make sure they will not be damaged by moving equipment.

• Protect components from damage, wear, and harsh environment conditions.

• Allow ample room for maintenance, panel accessibility, and cover removal.

• Protect equipment with safety devices as specified by applicable safety regulations.

• If safety devices must be removed for installation, install them immediately after the work is completed and check

them for proper functioning prior to returning power to the circuit.

Failure to follow these warnings may result in serious injury or equipment damage.

IMPORTANT INFORMATION

• IEC - International Standards and Conformity Assessment for all electrical, electronic and related technologies

• IEC 60364 - Electrical Installations in Buildings

• FAA Advisory: AC 150_5340_26 (current edition) Maintenance of Airport Visual Aid Facilities

• ANSI/NFPA 79, Electrical Standards for Metalworking Machine Tools.

• National and local electrical codes and standards.

WARNING

IMPROPER USE

Using this equipment in ways other than described in this manual may result in personal injury, death or property and

equipment damage. Use this equipment only as described in this manual.

THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR EQUIPMENT DAMAGE.

WARNING

FOREIGN OBJECT DAMAGE - FOD

• Only use fasteners of the same type as the one originally supplied with the equipment.

• Always tighten the fasteners to the recommended torque. Use a calibrated torque wrench and apply the

recommended adhesive type.

• Obey the instructions of the adhesives necessary for the fasteners.

Failure to follow these warnings may cause the fasteners to loosen, damage the

equipment, potentially to loosen the equipment. This can lead to a highly dangerous

situation of FOD, with potential lethal consequences.

1.2.4 Operation

1.2.5 Storage

1.2.6 Material Handling

Precautions

CAUTION

IMPROPER OPERATION

• Only qualified personnel, physically capable of operating the equipment and with no impairments in their judgment

or reaction times, should operate this equipment.

• Read all system component manuals before operating this equipment. A thorough understanding of system

components and their operation will help you operate the system safely and efficiently.

• Before starting this equipment, check all safety interlocks, fire-detection systems, and protective devices such as

panels and covers. Make sure all devices are fully functional. Do not operate the system if these devices are not

working properly. Do not deactivate or bypass automatic safety interlocks or locked-out electrical disconnects or

pneumatic valves.

• Protect equipment with safety devices as specified by applicable safety regulations.

• If safety devices must be removed for installation, install them immediately after the work is completed and check

them for proper functioning.

• Route electrical wiring along a protected path. Make sure they will not be damaged by moving equipment.

• Never operate equipment with a known malfunction.

• Do not attempt to operate or service electrical equipment if standing water is present.

• Use this equipment only in the environments for which it is rated. Do not operate this equipment in humid,

flammable, or explosive environments unless it has been rated for safe operation in these environments.

• Never touch exposed electrical connections on equipment while the power is ON.

Failure to follow this instruction can result in equipment damage.

CAUTION

IMPROPER STORAGE

If equipment is to be stored prior to installation, it must be protected from the weather and kept free of condensation

and dust.

Failure to follow this instruction can result in equipment damage.

CAUTION

ELECTROSTATIC SENSITIVE DEVICES

This equipment may contain electrostatic sensitive devices.

• Protect from electrostatic discharge.

• Electronic modules and components should be touched only when this is unavoidable e.g. soldering, replacement.

• Before touching any component of the cabinet you should bring your body to the same potential as the cabinet by

touching a conductive earthed part of the cabinet.

• Electronic modules or components must not be brought in contact with highly insulating materials such as plastic

sheets, synthetic fiber clothing. They must be laid down on conductive surfaces.

• The tip of the soldering iron must be grounded.

• Electronic modules and components must be stored and transported in conductive packing.

Failure to follow this instruction can result in equipment damage.

WARNING

UNSTABLE LOAD

• Use extreme care when moving heavy equipment.

• Verify that the moving equipment is rated to handle the weight.

• When removing equipment from a shipping pallet, carefully balance and secure it using a safety strap.

Failure to follow these instructions can result in death, serious injury, or equipment

damage.

Advanced Control Equipment (ACE2)

96A0357 Rev. F

To use this equipment safely:

1.2.7 Action in the Event

of a System or Component

Malfunction

1.2.8 Maintenance

1.2.9 Maintenance and

Repair

DANGER

ARC FLASH AND ELECTRIC SHOCK HAZARD

• Do not operate a system that contains malfunctioning components. If a component malfunctions, turn the system

OFF immediately.

• An open airfield current circuit is capable of generating >5000 Vac and may appear OFF to a meter.

• Never unplug a device from a constant current circuit while it is operating. Arc flash may result.

• Disconnect and lock out electrical power.

• Allow only qualified personnel to make repairs. Repair or replace the malfunctioning component according to

instructions provided in its manual.

Failure to follow these warnings will result in death or equipment damage.

WARNING

ELECTRIC SHOCK HAZARD

• Do not operate a system that contains malfunctioning components. If a component malfunctions, turn the system

OFF immediately.

• Disconnect and lock out electrical power.

• Allow only qualified personnel to make repairs. Repair or replace the malfunctioning component according to

instructions provided in its manual.

Failure to follow these warnings will result in death or equipment damage.

DANGER

ARC FLASH AND ELECTRIC SHOCK HAZARD

Allow only qualified personnel to perform maintenance, troubleshooting, and repair tasks.

• Only persons who are properly trained and familiar with ADB Airfield Solutions equipment are permitted to service

this equipment.

• An open airfield current circuit is capable of generating >5000 Vac and may appear OFF to a meter.

• Never unplug a device from a constant current circuit while it is operating. Arc flash may result.

• Disconnect and lock out electrical power.

• Always use safety devices when working on this equipment.

• Follow the recommended maintenance procedures in the product manuals.

• Do not service or adjust any equipment unless another person trained in first aid and CPR is present.

• Connect all disconnected equipment ground cables and wires after servicing equipment. Ground all conductive

equipment.

• Use only approved ADB Airfield Solutions replacement parts. Using unapproved parts or making unapproved

modifications to equipment may void agency approvals and create safety hazards.

• Check the interlock systems periodically to ensure their effectiveness.

• Do not attempt to service electrical equipment if standing water is present. Use caution when servicing electrical

equipment in a high-humidity environment.

• Use tools with insulated handles when working with airfield electrical equipment.

Failure to follow these warnings will result in death or equipment damage.

Inhaltsverzeichnis

Andere ADB Steuereinheit Handbücher

ADB

ADB L-854 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung