Addonics Technologies RAID Tower IX RT93SDEU3 Bedienungsanleitung

Technical Support

If you need any assistance to get your unit functioning properly, please have

your product information ready and contact Addonics Technical Support at:

Hours: 8:30 am - 6:00 pm PST

Phone: 408-453-6212

Email: http://www.addonics.com/support/query/

www.addonics.com

T E C H N O L O G I E S

RAID Tower IX

(RT93SDEU3)

User Guide

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Installing drivesinto the

RAID Tower IX

1. Be sure the lock on each drive door is in an

unlock position. If not, use the key that comes

with the Disk Array to unlock the drive door. Pull

on the door lever to swing open the drive door all

the way.

2. Slide a 3.5” SATA hard drive into the drive slot

with the drive connector side facing in. Be sure to

orient the hard drive correctly as shown in the

yellow label on the inside of the drive door – with

drive door swing open at the bottom, the top of

the hard drive should face to the right. The drive

should slide all the way into the slot with very

little resistance. Forcing the drive into the slot

will cause drive damage or permanent

damage to the Disk Array.

3. Once the drive is all the way into the drive slot,

close the door all the way till the drive door latch

securely. This will engage power and data

connection with the hard drive. The LED lit for

the drive slot should lit if the Disk Array already

powered on. You may lock the drive door with the

key

4. To remove the hard drive from the Disk Array,

simply follow the step 2 – 3 in reverse.

Door Lock

Individual

Drive Bay

Door

Main Power

LED

Insert Hard Drives

with Top Facing Right

Drive Power &

Activity LED

for each Drive Bay

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

f. Press the RAID setting button with a ball point pen.

g. While pressing the RAID setting button turn on the system power

where the HPM is connected. The buzzer will sound while holding the

RAID setting button. Release it after at least 5 seconds for hardware

initialization. A single beep will be heard to indicate initialization is

completed.

h. Verify if the RAID array is detected by the system.

i. If the 5-port HPM-XUis connected to the motherboard onboard

SATA, on the CMOS setup utility, the raid array will display as

“Addonics H/W RAID5” if setup as a RAID5 array.

j. If the 5-port HPM-XUis connected to an eSATA host controller card,

on the RAID BIOS, the raid array will display as “Addonics H/W

RAID0” if setup as a RAID0 array.

k. If booted into Windows, in Disk Drives under Device Manager, the

raid array will display as “Addonics H/W LARGE” if setup as a

LARGE array.

l. Once raid array is verified, you can set the buzzer either ON or OFF.

12 3 4 5

SW1

BZS EZ M2 M1 M0

RAID 1& RAID 10 Mode

12 3 4 5

SW1

BZS EZ M2 M1 M0

Clone Mode

When 2 drives are

connected to the HPM-XU,

and DIP switch is set to this

setting, the 2 drives will be

configured as a 2-drive

RAID1 array.

Clone’s action is similar to

RAID1. However, all of the

hard drives will be mirrored.

Clone mode is useful

especially when users like

to copy data from a source

hard drive to the drives

connected to the HPM-XU.

RAID Setting Notes:

When 4 drives are connected to the HPM-XU, the 4 drives will be

configured as a 4-drive RAID10 array.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Notes on Spare Drives using the Easy RAID Setting (EZ)

When EZ function is ENABLED, the auto-rebuilding to spare drive is automatic.

The degraded RAID group will start rebuilding automatically by using the existing

spare drive.

* Spare drive can be either plugged after RAID building or a new drive can be plug

as the spare drive when RAID rebuild is required.

When will rebuild action start?

•When the raid fails and EZ is enabled, the HPM-XUwill

automatically rebuild the RAID group using the spare.

•When the raid fails and EZ is disabled, the HPM-XUwill NOT

rebuild the raid group unless you install a good drive to replace the

failed drive.

Connecting the Power Cable and RAID Tower to the

Computer

a. Connect the power cord provided from the wall

outlet to the back of the tower.

b. Make sure the power is off (power LED light

should be off).

Power on/off control

a. A main power switch is located at the back of

the tower. Turn the switch on. Another auxiliary

switch is located on the front of the tower.

b. Make sure the power is off on the auxiliary

switch (power LED light should be off).

c. Power on the tower.

Power

Switch

Power

Switch

Bottom Front

HDD LEDs

Screws

Connect each of the Port Multipliers to the

computer using either a USB 3.0 or eSATA

cable. Connector

www.addonics.com

Phone: 408-573-8580

Fax: 408-573-8588

Email: http://www.addonics.com/sales/query/

Inhaltsverzeichnis

Andere Addonics Technologies Disk-Array-System Handbücher

Addonics Technologies

Addonics Technologies RTIV535HEU3 RAID Tower IV Bedienungsanleitung

Addonics Technologies

Addonics Technologies AESN4DA25 Bedienungsanleitung

Addonics Technologies

Addonics Technologies AESN4DA25-N Bedienungsanleitung

Addonics Technologies

Addonics Technologies R14ES Bedienungsanleitung

Addonics Technologies

Addonics Technologies SRDAP46SL Bedienungsanleitung

Addonics Technologies

Addonics Technologies SR46S4R5HM Bedienungsanleitung

Addonics Technologies

Addonics Technologies S4SHU3 Bedienungsanleitung

Addonics Technologies

Addonics Technologies AESN5DA35 Bedienungsanleitung

Addonics Technologies

Addonics Technologies Z4SN25NML Bedienungsanleitung

Addonics Technologies

Addonics Technologies RAID Tower XIII RT134SDMS Bedienungsanleitung

Beliebte Disk-Array-System Handbücher anderer Marken

Fujitsu

Fujitsu ETERNUS DX60 S2 Bedienungsanleitung

Accom

Accom WSD/2XTREME Bedienungsanleitung

HP Compaq Presario,Presario 4400 Gebrauchsanweisung

ATTO Technology

ATTO Technology Diamond Storage Array V-Class Bedienungsanleitung

National Instruments

National Instruments RMX-8268 Bedienungsanleitung

Overland Tandberg

Overland Tandberg SnapServer DX1 Bedienungsanleitung

easyRAID

easyRAID Q08QA-2GR2 Bedienungsanleitung

NEC

NEC NF2300-SR412E Bedienungsanleitung

EMC

EMC iomega StorCenter px12-350r Bedienungsanleitung

Infortrend

Infortrend EonStor A08U-C2411 Bedienungsanleitung

SE Audiotechnik

SE Audiotechnik M-F3 Bedienungsanleitung

Buffalo

Buffalo HD-QHU3R5 Bedienungsanleitung

HP StorageWorks XP128 Bedienungsanleitung

HP StorageWorks P2000 Leitfaden

HP 4400 Enterprise Bedienungsanleitung

G-Technology

G-Technology G-RAID2 Bedienungsanleitung

HP STORAGEWORKS XP24000 Bedienungsanleitung

Bosch

Bosch DVA-16K SCSI Bedienungsanleitung