ADEMCO 661 Bedienungsanleitung

The No. 661 Printer is designed to work wjth, and is controlled by, the No. 660

Digital Communicator Receiver or the No. 667 Mini-Modularm Monitor.

It permanent ly records the date, time, account number and type of emergency for

all alarm calls received at the central monitoring station.

CONTROLS 8,INDICATORS

POWER ALARM

ON REPORTING

0 0

STATUS/PRINT

DIAGRAM l- FRONT PANEL

I. “Power On” Lamp - indicates printer has power’applied.

2. “Alarm Reporting” Lamp - indicates printer is- “on line”, receiving an alarm

cal I.

3. “Status/Print” Button - causes a printout when used with the No. 660 Receiver.

- calls for a status report when used with the No. 667

Mini-Modularm Monitor

DIAGRAM 2-BACK PANEL (see page 54)

I. “Day of Year” - these three buttons establish the date.

2. “Hour” -’ self-explanatory.

3. “I Min.” - self-explanatory.

4. “Pr i nt” - used for testing the print mechanism. Causes a printout, whether

the printer is used with the No. 660 Receiver or the.No. 667

Mini-Modularm Monitor.

It will be necessary to set the date during the initial installation, on each New

Year’s Day, and possibly in the event of equipment failure.

www.PDF-Zoo.com

firealarmresources.com

loo 10 1 HR 1MH PRINT

I I I

MYCFYEAR

UAGRAM 2-BACK PANEL

The time will require adjustment during the initial installation and as required

for correction. Although adjustment is not frequently required, the time printed

out should be routinely checked. Before adjusting the time, note the following:

I. The time and date push buttons are quite sensitive. Care should be

taken to avoid pushing them more than the number of times required.

2. Time adjustments should be corrected in the following sequence:

1st - Minutes.

2nd - Hours. (Push a sufficient number of times to set the proper AM

or PM hour. 1

3rd - Day of Year

To test the printer, depress the “print” button and check the sample print-out

of the date, time, etc. Disregard any code information that may be printed out

during test.

FUSES:

There are two fuses located on the back of the panel. The top fuse, the Ademco

No. 8113 is a 3 amp “slo-blo” fuse which protects the No. 661 from internal short

circuits. The bottom fuse, the Ademco No. 90 is a 3/8 amp “slo-bIo” fuse for the

110-120 V.AC.

www.PDF-Zoo.com

firealarmresources.com

FIFTEEN-PIN INPUT CONNECTOR:

This connector mates the No. 661 to the No. 660 Receiver, or the No. 667 Mini-

Modularm Monitor. The cable supplied is for use with the No. 660 and connects

to a connector marked “printer” on the back of the No. 660. A different cable

(supplied with the No. 667) is used with the Mini-Modularm Monitor.

TWO-PIN CONNECTOR:

Mates the No. 661 Printer to the No. 665 Power Transfer Unit.

INSTALLATION:

Installing the No. 661 Printer requires that:

I. The appropriate fifteen-pin connector cord to the No. 660 or the No. 667

is plugged in.

2. The A.C. cord is plugged in.

3. The time

and

date adjustments are made properly as described above.

4. The two-pin connector cord is p I ugged

Unit is used, n if the No. 665 Power Transfer

OPERATION:

When an incoming alarm call is received, the printer will “clear” by, stamping

once. The date and time will appear to the left and a row of “O’s” will appear

to the right:

(DATE 1 (TIME)

354 M 3:4l 000 0

After the alarm code has been decoded by the No. 660 or the No. 667, the printer

will stamp the date and time again on the left and the account number and alarm

code on the right:

(DATE) (TIME) ACCOUNT ALARM

P NUMBER CODE

354 M 3:4l 321 I

Account numbers and alarm codes are set in advance by the alarm installation com-

pany.

A sample printer tape section is shown below:

354 M 3:4l 321 I

354 M 3:4l 000 0

PAPER FEED

www.PDF-Zoo.com

firealarmresources.com

NOTE:

I. It is the 354th day of the year (December 20, or December I9 in a Leap

Year).

2. The time is 3:4l P.M.

3. The account number is 321.

’ 4. Alarm code I has been received.

Observe that the printout will clear out and print one row of zeros immediately

upon receiving an incoming message. This means,alI messages received at the cen-

tral monitoring station will cause the printer t-operate.

PREPARING THE PRINT ASSEMBLY FOR SERVICING

To prepare the printer for a paper change or for the inserti’on of a new ribbon

(not just re-inking), take the following steps referring to Diagram 3:

I. Pull out the print assembly by its handle until its back plate hits the

stops in the housing.

2. Holding the assembly with both hands, lift the front up until the rear

of the assembly clears the

back

stops and drops out of the housing. Put

the assembly on a table with its front plate hanging over the edge.

3. Grasp the roller bar behind the paper roll and swing it up until the

paper roll assembly latches on the right side.

4. Unlatch, the front plate by pulling its bottom edge towards you.

5. Putting pressure under the handle, lift the front plate up and then swing

it up and back toward the paper roll assembly until its top edge latches

into the two notches on the paper roll assembly. (See Diagram 4).

www.PDF-Zoo.com

firealarmresources.com

DIAGRAM 4 -

6. Refer to the instructions below for paper loading and ribbon changing.

PAPER LOADING

I .

a’ 2.

Prepare the print assembly for a paper change by referring to the pre-

paration section below. Be sure the paper roll assembly and the front

plate are latched together properly.

Remove the paper shaft by pushing it in on the right hand side. Discard

the old paper core and replace it with Ademco No. 666 Printer Paper. Be

sure the paper goes over the top, under the guide and roller, toward

the front plate.

Be certain that the paper roll rotates freely on its shaft. This is

essential for proper paper advance.

Unwind approximately 6” of paper from the roll

space between the front plate and the paper ro and insert it in the

‘I I .

Carefully lay the print assembly on its left s

bottom faces you. ide and turn it so the

\I I

GUIDE

ROLLER 1

GUIDE ROLLER 2

GUIDE ROLLER 3

GUIDE ROLLER 4

PAPER ADVANCE

ROLLER

DIAGRAM 6 57

www.PDF-Zoo.com

firealarmresources.com

6. Pull about 12” of paper out from the bottom and then bring it around the

outside of guide roller I, (See Diagram 51, behind guide roller.2 and

then through the slot between guide rollers 2 and 3. The paper should

now be coming out toward you. (See Diagram 6) Now bring the paper

around guide roller 3 and through the opening between guide roller 4 and

the paper advance rol ler. (See Diagram 7) Pull the paper out through

the front of the print assembly, leaving about IO” of paper to work with.

7. Carefully put the print assembly right side up again with the paper and

front edge of the assembly hangin 9 over the end of the table.

8. Thread the paper through the slot in the front plate just below the

yellow plastic window.

9. Keeping the paper taut, gently un atch the front plate from the notches

in the paper roller assembly and et it drop down and latch into its

normal position. Make sure that the front plate is under the lip of the

latching bar. (See Diagram 3).

IO. Let the paper roll assembly gently drop into position by holding it

and pushing in the latching mechanism on the right hand side.

I I. Check to make sure paper loading has been done properly by pushing the

solenoid up and down manually at least 12 times. This should make the

paper move forward.

12. Print Spacing Adjustment. If the paper does not advance with adequate

separation between lines, the paper advance roller may not be adjusted

properly. If this is the case, the two bushings that support this

roller (see Diagram 3) have to be adjusted. To prepare the bushings

for adjustment, remove the two screws that support each of them, then:

a. To increase separation between printed I

bushing clockwise and the left side bush

,The same adjustment must be made to both

the paper does not come out crooked.

nes, turn the right side

ng counter-c lockw i se.

bushings to make sure that

b. To decrease separation between printed I i nes, turn the right side

bushing counter-clockwise and the left side bushing clockwise. The

same adjustment must be made to both bushings to make sure that the

paper does not come out crooked.

13. Put the print assembly back into the main housing by tilting the front.?:

of the assembly up and placing the back plate behind the stops at the

top of the main housing. Once the top of the back plate is in, lower

the assembly and slide it back into place. Be sure the front..pIate is

tightly up against the main housing..

RE-INKING PROCEDURE (NO. 8111 INK CARTRIDGE)

The No. 661 comes supplied with enough ink for approximately 45,000 to 70,000

print-outs. To re-ink:

I. Pull the print assembly out approximately 6” from the main housing.

2. Looking just beyond the top printed circuit board, locate the inkwell.

www.PDF-Zoo.com

firealarmresources.com

Ir;cKWELL

Remove the cap from Ademco’s No. 8111 Ink Cartridge.

Insert the ink cartridge into the inkwell.

Using a pair of diagonal cutters or a knife, cut an air entrance into

the top of the ink cartridge.

Allow the ink to drain into the inkwell. This will require approxi-

mately 5 minutes. It will take an additional I5 minutes at room temper-

ature for the ink to be absorbed by the inking roller. During this time,

do not open the print assembly to change the paper or turn the print

assembly upside down, as this action will cause the ink to spill out

from the reservoir.

Push the solenoid plunger down approximately 25 to 50 times to re-ink

the ribbon.

CHANGING THE RIBBON (Nd. 8112 RIBBON)

Prepare the print assembly for a ribbon change by referring to the

preparation section above. EIe sure the paper roll assembly and front-

plate are latched together properly.

2. Turn the print assembly upside down so that it rests on the paper

roller assembly and the back plate. (See Diagram 8). Pull the paper

back so that the ribbon is exposed.

www.PDF-Zoo.com

firealarmresources.com

RIBBQN GUIDE

,T----?

3. Lift the old ribbon off the spring-loaded ribbon guide. This guide will

have to be pressed down while the ribbon is removed.

4. Move the abrasive wheel to the right and remove the old ribbon from be-

tween the wheel and the inking roller. The ribbon may now be completely

removed.

5. Install a new Ademco No. 8112 Endless Ribbon. Carefully thread the new

ribbon through the fixed guides on the sides of the print assembly,

making sure to fold the ribbon at the corner guides.

6. Bring the ribbon over the top of the inking roller guide and down be-

tween the inking roller and the abrasive wheel. The abrasive wheel

will have to be moved slightly towards the right to accomplish this.

7. Push the spring-loaded guide down and put the ribbon over it until it

rests properly in place.

Put the paper back through the slot in the front plate.

9. Turn the print assembly right side up.

IO. Keeping the paper taut, gently unlatch the front plate from the notches

in the paper roller assembly and let it drop down and latch into its

normal position. Make sure that the front plate is under the lip of

the latching bar.

II. Let the paper roll assembly gently drop into position by holding it and

pushing in the latching mechanism on the right hand side.

12. Push the solenoid plunger manually 25 to 50 times in order to ink the

new r i bbon.

13. Put the print assembly back into the main housing by tilting the front

of the assembly up and placing the back platebehind the stops at the

top of the main housing. Once the top of the back plate is in, lower

the assembly and slide it back into place. Be sure the front plate is

tightly up against the main housing.

www.PDF-Zoo.com

firealarmresources.com

PROBLEM CHECKS

I . RECE IVER WI LL NOT WORK AT ALL

(NO LAMP TEST AND NO POWER ON LAMP).

A,B,C,D,J ,N

II. RECEIVER WILL NOT PICK UP ON INCOMING

CALL.

E,F,N

I I I. RECEIVER WILL NOT G

(ACKNOWLEDGEMENT) TO IVE “HANDSHAKE”

COMMUNICATOR. G

IV. RECEIVER WILL NOT DISPLAY MESSAGE. K,L

V. RECEIVER WILL NOT GIVE HANG UP SIGNAL

TO COMMUNICATOR.

VI. RECEIVER WILL NOT ACTIVATE PRINTER.

M, 1

VII. WITH TWO-RECEIVER OPERATION (ONE

AS A SLAVE IN THE MONITOR MODE), MASTER

RECEIVER HANGS UP ON INCOMING COMMUNI-

CATORS. 0

VIII. DIGITS CHANGE ON DISPLAY WHEN SILENCE

ALERT BUTTON IS DEPRESSED. P

NOTE: THE NO. 660 RECEIVER WILL ONLY PROCESS ADEMCO 8 SILENT KNIGHT

FORMATS.

CHECKS AND POSSIBLE REMEDIES

A. Check to see if Power On lamp is I it.

B. Check wall outlet for output of 110 V. AC. Be certain the outlet is

a 24 hour outlet - not switch or timer controlled.

C. Check I ine cord for breaks. Put volt-ohmmeter on R X 1 scale. Place

probes across prongs of male plug. Meter should indicate approximately

8ohms. Next set meter at R X 1K scale and check each prong against the

ground prong. Meter should indicate infinity.

D. Check fuse at rear of No. 660.

E. Check phone lines. Remove No. 8115 cord (connected to receiver) from

phone block. Place a milliamp meter across telephone block. The meter

should indicate an approximate 30-60 milliamp reading.

F. Check No. 8115 direct connect cord on receiver. With volt-ohmmeter set

at R X 1 scale, attach probes to solderless connectors of No. 8115. The

meter should indicate infinity. Next p’lace a short jumper across the

red and green wire at the head of the No. 8115. Meter should indicate

approximately 8 ohms.

www.PDF-Zoo.com

firealarmresources.com

G. Perform test shown in Installation Procedure No. 3. This test checks

two-way operation.

H. Check “Manual Auto” switch at rear of No. 660. If no printer is used,

“Manua I” mode should be used and operator must press “Message Received”

button after “Message Va I id” Iamp I ights. If printer No. 661 is used,

the switch shou Id be in the “Auto” mode. A hang-up tone will be given

automatically with switch in this mode.

I . Make continuity check of male prongs on interconnect cord supplied with

No. 661.

J. Check all connections to No. 665 if used.

NOTE: It is extremely important that the No. 665 instructions are

followed closely.

K. Using telephone hand test set (Ademco No. 2611, listen on phone lines

for tones from No. 662 or 669. If none appear, the fault is with the

No. 662 or 669.

.L. Recheck lamp test. Be certain all lamps are working. All 888s should

I ight.

:“I .

Be certain No. 661 printer has “Power On” lamp lit indicating electric

outlet and line cord are working correctly.

N. Remove cover of No. 660 carefully. Check all individual connections

and plugs. Be certain all printed circuit boards are seated properly.

0. Reverse location of receivers, i.e. put slave receiver in master re-

ceiver location and vice versa. Remember to restore jumpers in first

slave and cut jumpers in original master.

Also always try to locate master and slave in same telephone exchange.

. P. When a remote warning device is used, it must be isolated from No. 660

using a No. 540 switching module and separate 6 volt power supply. ’

See No. 660 Instructions: INSTALLATION PROCEDURES, Section 4.

NOTE: If a call director No. 671 is used in conjunction with the No. 660,

a slave receiver (i.e. a second receiver i n the “mon i to? mode)

mav be used.

www.PDF-Zoo.com

firealarmresources.com

Inhaltsverzeichnis

Andere ADEMCO Drucker Handbücher

ADEMCO

ADEMCO 6220 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung