ADEMCO RapidEye plus Montageanleitung
PLUS
Remote Video Unit
Installation and Setup
Guide
K4859 12/99
PLUS
Remote Video Unit
Installation and Setup
Guide
© 1999 Ademco Group Video Products Division. All rights
reserved.
The information contained in this document is subject to change
without notice. Ademco and its affiliates can assume no
responsibility for errors and/or omissions contained in this
information.
All rights reserved. No part of this publication may be reproduced,
transcribed, stored in a retrieval system or transmitted in any form
whatsoever, without the prior written consent of Ademco.
Rapid Eye is a registered trademark of Ademco. All other
trademarks and registered trademarks belong to their respective
companies.
Microsoft, Windows, and Windows NT are registered trademarks of
Microsoft Corporation. U.S. Robotics, Courier, and I-Modem are
registered trademarks of 3Com Corporation.
The JSC232/485 (RS-232 to 485) converter is a product of Javelin
Systems.
Changes or modifications not expressly approved by Ademco
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in
accordance with the instruction guide, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
Guide Revision
Date Remote Unit Part Number
November 26, 1999 JRRP4
Rapid Eye Remote Video Unit Installation and Setup Guide
Table of Contents i
Table of Contents
About This Guide................................................................................1
Related Documents.....................................................................1
About the Rapid Eye Remote Video System ......................................1
1.0 Unpacking the Remote Video Unit...............................................3
2.0 Rear Panel Connectors................................................................5
3.0 Installing the Remote Video Unit..................................................8
3.1 Connecting Cameras............................................................9
Setting DIP Switches..........................................................9
3.2 Alarm Connections .............................................................11
3.3 Control Output Connections ...............................................12
3.4 Communication via LAN.....................................................12
Selecting an IP Address ...................................................12
Entering the IP Address....................................................12
3.5 Connecting the Communication Line..................................15
3.6 Connecting Rapid Eye to the Audio Panel..........................16
Alarm Inputs .....................................................................17
Control Outputs.................................................................17
4.0 Connecting PTZ Domes ............................................................18
4.1 RS-232 Converter...............................................................19
4.2 Required Cables.................................................................20
4.3 Daisy-chaining Multiple Domes...........................................20
5.0 Powering Up the Remote Unit ...................................................21
6.0 Powering Down the Remote Video Unit.....................................21
6.1 Moving the Rapid Eye PLUS Remote Video Unit...............21
Appendix A: Getting Help..................................................................23
Appendix B: Remote Site Information...............................................24
Appendix C: Common CCTV Practices...........................................25
C.1 Lighting Characteristics......................................................25
C.2 Coaxial Cable.....................................................................26
C.2.1 Connectors.............................................................27
C.2.2 Amplifiers ...............................................................27
C.2.3 Coaxial Cable Checklist.........................................28
Rapid Eye Remote Video Unit Installation and Setup Guide
ii Table of Contents
C.3 Potential Problems............................................................. 28
C.3.1 Ground Loops and Hum Bars................................ 29
C.3.2 Electrical Interference............................................ 29
C.3.3 Recommendations ................................................ 30
C.4 Backup Power.................................................................... 30
C.4.1 Line Conditioner UPS System...............................31
Appendix D: Configuring Alarm Inputs ............................................ 32
Enabling the Alarm Input Type......................................... 32
Appendix D: Full Duplex Null Modem Wiring Diagram.................... 33
Index i
Rapid Eye Remote Video Unit Installation and Setup Guide
About This Guide 1
About This Guide
This guide is intended for people who will be responsible for the installation
of the Rapid Eye PLUS remote video Unit.
Related Documents
[1] Rapid Eye Remote Video System Operator Software User Guide
[2] Rapid Eye Remote Video System MANAGER Software User Guide
About the Rapid Eye Remote Video System
Rapid Eye is an information management, quick-response video
telesurveillance system. It is designed to display visual information from
distant sites, and has been specifically designed to assist in:
•alarm verification and identification
•remote Guard Tour
•crisis intervention
•remote business management
•remote monitoring and surveillance
Figure 1: Typical System Interconnect
Rapid Eye Remote Video Unit Installation and Setup Guide
2 About the Rapid Eye Remote Video System
The Rapid Eye Video Telesurveillance system consists of the following two
major components, that communicate via a communication link such as
Public Switched Telephone Network (PSTN), Integrated Services Digital
Network (ISDN), or Frame Relay:
1. Rapid Eye PLUS remote video Unit: This component connects
directly into standard Closed Circuit TV (CCTV) systems. It provides
the ability to view video images from cameras from distant sites, to
process and transmit alarm information, and to store video images
before, during, and after an alarm event has occurred. It may be
connected to a central monitoring site using PSTN, ISDN, or Frame
Relay. This guide describes how to install this unit.
2. Rapid Eye OS Operator Software: This is a Windows-based software
product that allows alarm and video information to be retrieved from the
Remote Video Unit. (Refer to the Rapid Eye Remote Video System
Operator Software User Guide for installation and operating
instructions).
The system can handle up to 16 dry contact alarm inputs, up to 16 camera
inputs, and can deliver 8 control outputs.
Using the Operator Software, the Rapid Eye Remote Video Unit can be
configured to operate in a variety of different modes:
•Capture video images before, during, and after an event (alarm)
•Process and transmit stored or live video images
•Process and transmit alarm information
•Control external devices
Rapid Eye Remote Video Unit Installation and Setup Guide
1.0 Unpacking the Remote Video Unit 3
1.0 Unpacking the Remote Video Unit
Package Contents
The packing container has the following items:
•This installation guide
•Rapid Eye Remote Video Unit
•Power cord
•Warranty and software license
Please check the package for all of the above items. If any items are missing,
contact Ademco.
1. Open the packing container and remove the Rapid Eye PLUS remote
video Unit.
2. Remove the packing styrofoam ends from the unit and place the unit on
a working surface that is clear of obstacles.
3. Inspect the unit for obvious damage.
a. If you see damage to the unit, call your designated Ademco
representative and describe the problem. Please have your Serial
Number available (the serial number for the Remote Video Unit is
located on the underside of the unit). If necessary, your sales
representative will supply a Return Authorization Number (RAN)
that must be prominently displayed on the shipping container should
the equipment be returned.
b. Re-pack the unit, along with the other contents in the original
shipping container and return to Ademco. Refer to Appendix A:
Getting Help for the shipping address.
☞Important: Do not return equipment to Ademco without first
contacting Ademco Customer Support. Equipment returned
without prior authorization will be returned to the sender.
Your Rapid Eye equipment is covered by the terms of your ownership
agreement.
Rapid Eye Remote Video Unit Installation and Setup Guide
4 1.0 Unpacking the Remote Video Unit
☞Note: Do not remove the factory seals on the Rapid Eye PLUS
remote video Unit chassis. The Remote Video Unit has no
customer serviceable items inside and must be returned to
Ademco for repair. Breaking the factory seals will void your
warranty.
The registration process ensures prompt service of your equipment should
you require it, whether the system is under warranty or not.
Inhaltsverzeichnis
Andere ADEMCO Sicherheitssystem Handbücher
ADEMCO
ADEMCO LYNX Bedienungsanleitung
ADEMCO
ADEMCO 4180 Bedienungsanleitung
ADEMCO
ADEMCO 4110 Bedienungsanleitung
ADEMCO
ADEMCO Alpha Vista 5130XT Bedienungsanleitung
ADEMCO
ADEMCO 4140XMP Bedienungsanleitung
ADEMCO
ADEMCO Vector Bedienungsanleitung
ADEMCO
ADEMCO 4130XM Bedienungsanleitung
ADEMCO
ADEMCO Defender II Bedienungsanleitung
ADEMCO
ADEMCO Vista AT 4140 Bedienungsanleitung
ADEMCO
ADEMCO Security System VISTA-15 Bedienungsanleitung
ADEMCO
ADEMCO 5800WAVE Montageanleitung
ADEMCO
ADEMCO 5120XM Bedienungsanleitung
ADEMCO
ADEMCO 4110XM Bedienungsanleitung
ADEMCO
ADEMCO via30+ Bedienungsanleitung
ADEMCO
ADEMCO Vista 4120 Bedienungsanleitung
ADEMCO
ADEMCO Vista Series 4120EC Bedienungsanleitung
ADEMCO
ADEMCO Vista-10SEa Bedienungsanleitung
ADEMCO
ADEMCO VISTA-48D Montageanleitung
ADEMCO
ADEMCO VISTA-20P Series Betriebsanleitung
ADEMCO
ADEMCO VISTA-128FBP Betriebsanleitung
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung