Adeunis RF ARF26 Bedienungsanleitung

05-11-V3-psn 1

GENERAL USE 2

CHOICE OF TRANSMISSION CHANNELS 2

DIMENSIONS / PIN ASSIGNMENT 3

CHANNEL MANAGEMENT 3

Principle 3

Timing 4

Transmissionmode 4

Receivermode 5

Dataclkmode 5

Standbyemode 6

Reset6

PROTOCOL 7

Levelbitencoding 7

Levelframeencoding 7

RADIO CHANNEL MANAGEMENT 8

Radiochannelsettling 8

Wakeuptime 8

Transceiver turn around 9

RSSI 9

SPECIFICATIONS 11

INTEGRATION 12

REGULATION COMPLIANCE 13

ARF26

Use

Guide

ADEUNIS RF – 283 RUE LOUIS NEEL – 38920 CROLLES FRANCE

DESK : +33 (0) 4 76 92 07 77 – FAX +33 (0) 4 76 08 97 46 E.MAIL : ARF@ADEUNIS-RF.COM

________________________________________________________________________________________

SA au capital de 345.000 euros – SIRET 430 190 496 00017 – RCS Grenoble – NAF 322A

05-11-V3-psn 2

The ARF26 radio module is a multi-channel FSK digital transmission radio-frequency

transceiver using the 868-870 MHz band. This transceiver proposes up to 9 transmission

channels enabling two-way half-duplex digital links up to 25 kBps Manchester. The

transceiver is composed of "rough" radio components; the transmission protocol (data

encoding/decoding) and radio module programming are performed by the associated logic.

The 868-870 MHz band is subdivided into 4 sub-bands authorising different duty cycles: ≤

0.1 %, ≤1%, ≤10% and ≤100%. The duty cycle of the product has to be calculated to know

which of the sub-bands can be used by the application. The table below presents the

different sub-bands with their duty cycle and the maximum number of channels that can be

envisaged in each sub-band.

Sub-band

n° 1 2 3 4

Band edges

(in MHz)

868-868.6

868.7-869.2

869.4-869.65

869.7-870 (*)

Duty cycle ≤1% ≤0.1 % ≤10% up to 100%

Maximum

number of

channels

(*) The maximum apparent radiated power for sub-band #4 is limited to +7dBm.

The table below gives the details of the available channels:

Sub-band Channel Frequency

868-868.6 MHz 1 868.100 MHz

duty cycle 1% 2 868.300 MHz

3 868.500 MHz

868.7-869.2 MHz 4 868.783 MHz

duty cycle 0.1% 5 868.950 MHz

6 869.117 MHz

869.4-869.65 MHz

duty cycle 10% 7 869.525 MHz

869.7-870 MHz 8 869.775 MHz

duty cycle 100% 9 869.925 MHz

GENERAL USE

CHOICE OF TRANSMISSION CHANNELS

05-11-V3-psn 3

N.B.:

- The signals SLE, SCK and SDATA correspond to the 3-wire serial interface for

programming the transceiver registers.

- The radio module is supplied by an external power source between VDC and GND. The

supply voltage should be chosen in the 3-5V range.

•Principle

The transmitter and receiver have to be configured (frequency registers, control registers...) to

establish the radio link. This register configuration is performed by means of the SLE, SCK

and SDATA 3-wire serial bus.

The number of registers to be programmed depends on the operating mode: transmission,

receipt... Each word is programmed starting with the most significant bit (MSB) and each bit

is loaded on the rising front of SCK.

N.B:

- In transmission mode (Tx) and receipt mode (Rx), the programming is different for any one

channel.

- The transmitter and receiver have to work on the same channel to “understand” each other.

- For this programming, it is understood that low level corresponds to GND and high level to

VDC.

1 - GND RF

2 - ANTENNA

3 - VDC: 3 to 5V power supply

4 - GND: 0V ground

5 - DATAMSG: Data input/output

6 - SLE: Enable input

7 - SCK: Clock input

8 - SDATA: Programming data

input/output

9 - DATACLK: Received data

nchronisation cloc

DIMENSIONS

PIN ASSIGNMENTS

CHANNEL MANAGEMENT

05-11-V3-psn 4

•Timings

Programming of a register is performed according to the following timing diagram:

N.B.:

- The number of pulses for SCK corresponds to the number of bits to be sent and depends on

the register. In the example above, there are 37 clock pulses that correspond to the longest

- Between programming of 2 registers, SLE must be kept at “1” for a minimum time of

200 ns.

- The content of the registers (address included) for each operating mode is specified in the

following paragraphs. When programming a register, it is imperative to send the specified

number of bits (cf. tables below), no more no less, to avoid an incorrect programming.

•Transmission mode

In transmission mode, three 37-bit registers (the control register CTRL1 and frequency

registers F0 and F1) and one 7-bit register (control register CTRL3) have to be configured.

Programming of the registers must begin with F0, followed by F1, then CTRL3 and finish

with CTRL1. The table below presents the content of the registers according to the channel:

Channel F0 (hex)

37 bits F1 (hex)

37 bits CTRL3 (hex)

7 bits CTRL1 (hex)

37 bits

1 019CD440E2 03085464E6

2 01A57D72C4 034465D4C4

3 01FD05E6DE 03449DC4FA

4 01019DF274 0380CDF472 09DB005260

5 0188C45666 03855552F4 45

6 018804F4EE 03B195D248

7 01405DE244 03518540C4

8 01059DC6F4 03A1154240 09DB002260

9 01FC3DE658 03506D467E

05-11-V3-psn 5

•Receipt mode

In receipt mode, at least two 37-bit registers (the control register CTRL1 and frequency

registers must start with F2, followed by CTRL3 and finish with CTRL1. The table below

presents the content of the registers according to the channel:

Channel F2 (hex)

37 bits CTRL3 (hex)

7 bits CTRL1 (hex)

37 bits

1 05C14DD4C8

2 05B57DD2C4

3 05597C52E2

4 058884E26E

5 0539E5D4D0 44 0990000260

6 05C91C50EA

7 056DFD46D8

8 052D6544D0

9 05783DE2D8

•“DATACLK” mode

In receipt mode, a received data synchronisation clock can be available on the DATACLK pin

of the radio module (rising front in the middle of the data). To take advantage of this option,

the control register CTRL2 (27 bits) also has to be configured according to the maximum

transmission rate of the application. In “DATACLK” mode, programming must be started

with F2, followed by CTRL2 then CTRL3, and finally CTRL1.

The table below presents the content of CTRL2 according to the maximum transmission rate

of the application and the content of CTRL1 that has changed (for activation of the

DATACLK).

Transmission rate Transmission rate

(in Manchester) CTRL2 (hex)

27 bits CTRL1 (hex)

37 bits

2 kBps 1 kBps 7D40266

2.4 kBps 1.2 kBps 7D0AD55

4kBps 2 kBps 7CA0133

4.8kBps 2.4 kBps 7C8562B

9.6 kBps 4.8 kBps 7C42B15

10 kBps 5 kBps 7C40014 09B0000260

19.2 kBps 9.6 kBps 7C2160B

20 kBps 10 kBps 7C2000A

39.2kBps 19.6 kBps 7C10C05

40 kBps 20 kBps 7C10005

50 kBps 25 kBps 7C0CD04

05-11-V3-psn 6

N.B.:

- The content of CTRL1 is identical whatever the channel.

- In “DATACLK” mode, the contents of the registers F2 and CTRL3 are the same as in

paragraph 5.4.

- Consult us for other transmission rates.

•Standby mode

To switch to Standby mode, the registers CTRL3 then CTRL1 have to be programmed:

CTRL3 (hex)

7 bits CTRL1 (hex)

6 bits

45 (*) 12

(*): When switching to Standby mode from transmission mode, the register CTRL3 is already

at 45 (hex).

To return to the previous mode, CTRL1 and possibly CTRL3 have to be reprogrammed:

Previous mode CTRL3 (hex)

7 bits CTRL1 (hex)

6 bits

Transmission - 13

Receipt 44 13

•Reset

Reset of all the registers is performed by programming the RESET register:

RESET (hex)

6 bits

Content: 2E

After a reset, the radio module is in standby mode and all the registers have to be

reprogrammed as described above to switch to transmission or receipt mode.

05-11-V3-psn 7

On account of the ARF26 system transmission principle and of the modulation in phase lock

loop, the modulating signals must have a frequency comprised between 1 kHz and 25kHz.

Lower and higher frequencies cannot be transmitted, as they are filtered. This means, among

other things, that the link cannot transmit constant states with a duration of more than 500 µs.

•Level - Bit Encoding

Most conventional hardwired serial links transmit bytes in asynchronous manner using an

NRZ type encoding (1 logic bit = 1 electrical state). This results in the spectrum occupation of

the signals thus generated being about one decade. Furthermore, sampling of the bytes thus

received supposes perfect synchronisation of decoding on the start bit.

In the case of radio transmission, it is preferable to limit the spectrum of the signals to be

transmitted as far as possible, in particular towards low frequencies, even if this means

increasing the main frequency. Moreover, it is advantageous to reset the synchro on each

transmitted bit; receivers are in fact the cause of large duty cycle errors on the electrical states.

Bit encodings should therefore be preferred, for example those proposed below:

Manchester or two-phase:

Differential PWM:

•Level - Frame Encoding

Once the bits have been encoded, it is then imperative that they be transmitted according to a

frame structure; the radio link is very sensitive to binary flow breaks which can only be

minimised by “serialising” the bytes.

A conventional frame structure is shown below:

PROTOCOL

05-11-V3-psn 8

1Preamble: Electrical succession 101010... to fix the receiver polarisation and compensate

the channel settling time.

2Start pattern: Electrical pattern that marks the beginning of the useful data by a break in

the binary flow of the preamble.

3Useful part: Successions of bytes encoded at bit level.

4Stop pattern: Indicates the end of frame (necessary when the frame may be of variable

length).

•Radio channel setting:

This characteristic corresponds to the time required for the first valid bits to be obtained on

receipt on an ARF26 n°2 (DATAMSG2) after a frame has been transmitted from another

distant ARF26 n°1 module (DATAMSG1).

•Wake-up time (Start-up time):

This characteristic corresponds to the time required to switch from Standby mode (low

consumption) to ‘active’ mode (transmission or receipt).

RADIO CHANNEL MANAGEMENT

05-11-V3-psn 9

•Transceiver turn-around:

This characteristic corresponds to the time required to switch from transmission to valid

receipt or vice-versa on the same device, and therefore to a TX_RX control input status

change.

The 3-wire serial bus is bi-directional. It is therefore possible to read the status of certain

registers. The value of the RSSI (received signal strength indicator) is contained in the status

To know the value of these 6 bits, you have to go and read the status register according to the

following timing diagram:

- The first 4 bits (0101) correspond to the status register address.

- The 5th bit (1) selects register read mode.

T1: SDATA switching time from input to output on descending front of SCK: 50 ns max.

T2: data propagation delay time after a descending front: 50 ns max.

T3: SDATA switching time from output to input on rising front of SLE: 50 ns max.

The timings indicated in chapter 4.2 remain valid.

The value of the RSSI corresponds to bits D1 (LSB) to D6 (MSB). Bit D7 is of no interest.

The graph below gives a correspondence between the RSSI value and the received power

level.

RSSI

05-11-V3-psn 10

Caution:

- The RSSI level remains an indicator which has to be used with precaution. The curve

presented above may change somewhat from one product to the other.

- This RSSI level can also indicate the presence of a possible interfering source on the

channel used. It is not possible to ensure that the required signal coming from the remote

transmitter is detected and received by examining the RSSI only. The identity of the

transmitter also has to be checked by encodings in the transmitted frames.

The RSSI is a necessary but non-sufficient condition for obtaining correct receipt.

Inhaltsverzeichnis

Andere Adeunis RF Steuereinheit Handbücher

Adeunis RF

Adeunis RF Narrow Band NB868-500mW Bedienungsanleitung

Adeunis RF

Adeunis RF SIGFOX Si868-25mW Bedienungsanleitung

Adeunis RF

Adeunis RF Narrow Band NB868-25mW Bedienungsanleitung

Adeunis RF

Adeunis RF PULSE V4 Produkthandbuch

Adeunis RF

Adeunis RF ARF8133A Bedienungsanleitung

Adeunis RF

Adeunis RF Wireless-Mbus 25mW Bedienungsanleitung

Adeunis RF

Adeunis RF TWIMO Series Bedienungsanleitung

Adeunis RF

Adeunis RF SIGFOX Bedienungsanleitung

Adeunis RF

Adeunis RF ARF54 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung