ADJ Encore Profile 1000 WW Bedienungsanleitung

User Manual

ENCORE PROFILEENCORE PROFILE

1000 WW1000 WW

Rev 03/2021

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be trade-

marks or registered trademarks of their respective companies and are hereby acknowledged. All

non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera-

tion of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 2

Encore Profile 1000 WW Introduction

ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 3

Unpacking: Thank you for purchasing the Encore Prole 1000 WW by ADJ Products, LLC. Every

Encore Prole 1000 WW has been thoroughly tested and has been shipped in perfect operating condi-

tion. Carefully check the shipping carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your xture for any damage and be sure all acces-

sories necessary to operate the unit have arrived intact. In the event that damage has been found or

parts are missing, please contact our toll free customer support number for further instructions. Do not

return this unit to your dealer without rst contacting customer support.

Introduction: The ADJ Encore Prole 1000 WW is a DMX intelligent, high powered LED follow spot.

This follow spot has three operating modes: white dimmer mode, fade mode, and DMX control mode.

This xture can be used in a stand alone mode or connected in a Primary/Secondary conguration.

To optimize the performance of this product, please read these operating instructions carefully to

familiarize yourself with the basic operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please keep this manual with the unit for

future reference.

Customer Support: ADJ Products, LLC provides a customer support line, to provide help and to

answer any questions that might arise during set up or initial operation. You may also visit us on the

web at www.adj.com for any comments or suggestions. Service Hours and Monday through Friday

8:00am to 4:40pm PST.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or

moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, as

doing so will void your manufacturer’s warranty. In the unlikely event that your unit requires service,

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 4

Encore Profile 1000 WW Features

• Three Operating Modes

• Electronic Dimming 0-100%

• 5 Selectable Dimming Curves

• 4 Included Gobos

• DMX-512 protocol

• Locking 3-Pin & 5-Pin XLR Connector In/Out

• 3 DMX Modes: 1 Channel Mode, 2 Channel Mode, & 3 Channel Mode.

• ADJ LED RC2, ADJ UC IR, (Not Included) & Airstream IR compatible

• Power Cord Daisy Chain Capability (see the Power Cord Daisy Chain section of this manual)

Encore Profile 1000 WW Warranty Registration

The Encore Profile 1000 WW carries a 2 year limited warranty. Please fill out the enclosed warranty

card to validate your purchase. All returned service items, whether under warranty or not, must be

freight pre-paid and accompanied by a return authorization (R.A.) number. The R.A. number must be

clearly written on the outside of the return package. A brief description of the problem as well as the

R.A. number must also be written down on a piece of paper included in the shipping carton. If the unit

is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain an R.A.

number by contacting our customer support team on our customer support number. All packages

returned to the service department not displaying an R.A. number on the outside of the package will

be returned to the shipper.

Encore Profile 1000 WW Installation

The unit should be mounted using a mounting clamp (not provided), which should be attached to the

mounting bracket that is provided with the unit. Always ensure that the unit is firmly fixed to avoid

vibration and slipping while operating. Always ensure that the structure to which you are attaching

the unit is secure and is able to support at least 10 times the unit’s weight. Also, always use a safety

cable that can hold at least 12 times the weight of the unit.

The equipment must be installed by a professional, and it must be installed in a place where it is out

of the reach of people’s grasp.

ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 5

Encore Profile 1000 WW Safety Precautions

• To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture.

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord is frayed or broken.

• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is

used to reduce the risk of electrical shock and fire in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover for any reason. There are no user serviceable parts inside.

• Never operate this unit with the cover removed.

• Never plug this unit in to a dimmer pack.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit if it has been damaged in any way.

• This unit is intended for indoor use only. Use of this product outdoors voids all warranties.

• During long periods of non-use, disconnect the unit from main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point where they exit from

the unit.

• Cleaning - The fixture should be cleaned only as recommended by t he manufacturer. See the

Cleaning section of this manual for cleaning details.

• Heat - The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen onto, or liquid has been spilled into, the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a marked change in perfor-

mance.

Encore Profile 1000 WW DMX Set Up

ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 6

Power Supply: The ADJ Encore Profile 1000 WW contains an automatic voltage switch, which will

automatically sense the voltage when it is plugged into the power source. With this switch, there is no

need to worry about the correct power voltage, and this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol that is used as a form

of communication between intelligent fixtures and controllers. A DMX controller sends DMX data

instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture

to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most control-

lers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be

linked together and operate from a single controller, as long as all fixtures and the controller are DMX

compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible

when linking several DMX fixtures. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example, a fixture assigned a DMX address of 1 may be placed

anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a fixture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that

unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The Encore Profile 1000 WW can be

controlled via DMX-512 protocol. The Encore Profile 1000 WW has 3 DMX modes, which are listed

in the Operating Instructions section of this manual. The DMX address is set on the back panel of

the Encore Profile 1000 WW. Your unit and your DMX controller require a standard 3-pin or 5-pin XLR

connector for data input and data output (Figure 1). We recommend Accu-Cable DMX cables. If you

are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may

be purchased at almost all pro lighting stores). Your cables should be made with a male XLR connec-

tor on one end and a female XLR connector on the other. Also remember that DMX cable must be

daisy chained and cannot be split.

ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 7

Encore Profile 1000 WW DMX Set Up

Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground

lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the

shield conductor to come into contact with the XLR cable’s outer casing. Grounding the shield could

cause a short circuit and result in erratic behavior.

Special Note: Line Termination. When longer runs of cable are used, you may need to use a ter-

minator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor

which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is

inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a

cable terminator (ADJ part number Z-DMX/T) will decrease the chances of erratic behavior.

5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA trans-

mission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When insert-

ing standard 5-pin data cables into a 3-pin line a cable adaptor must be used. These adaptors are

readily available at most electronics stores. The chart below details a proper cable conversion.

ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 8

Encore Profile 1000 WW Operating Instructions

LCD Backlight On/Off:

To set the LCD backlight to turn off after 20 seconds, press the MODE button until “OTHER” is dis-

played, then press the SET UP button until “OTHER BLGT:XX” is displayed. “XX” represents the

current state. Press the UP or DOWN buttons to set the backlight to turn “OFF” after 20 seconds or

“ON” to stay on at all times.

Operating Modes:

The Encore Profile 1000 WW has three operating modes:

• Dimmer Mode - Adjust the intensity of the white color.

• Fade Mode - The unit will fade in and out.

• DMX Control Mode - This function will allow you to control each individual trait with a standard

DMX 512 controller.

Dimmer Mode:

1. Plug the fixture in and press the MODE button until “MANUAL WHIT:XXX” is displayed.

2. Press the UP and DOWN buttons to adjust intensity.

3. After the output intensity has been set, strobing can be activated by pressing the SET UP button.

4. “STRO” will be displayed, indicating that the device has entered strobing mode. The strobing can

be adjusted between “00” (strobing off) to “15” (fastest strobing).

DMX Mode:

Operating through a DMX controller gives the user the freedom to create custom own programs tai-

lored to his or her own individual needs. The Encore Profile 1000 WW has 3 DMX modes: 1 channel

mode, 2 channel mode, and 3 channel mode. See the Channel Mode sections of this manual for a

detailed description of each channel mode’s DMX traits.

1. This function will allow you to control each fixture’s traits with a standard DMX 512 controller.

2. To run your fixture in DMX mode, press the MODE button until “DMX MODE ADDR:XXX” is dis-

played. “XXX” represents the currently selected DMX address. Use the UP or DOWN buttons

to select your desired DMX address, then press the SETUP button to select your DMX Channel

mode.

3. Use the UP or DOWN buttons to scroll through the DMX Channel modes. The Channel modes

are listed below:

• 1 Channel DMX Mode (“CHAN: 01”)

• 2 Channel DMX Mode (“CHAN: 02”)

• 3 Channel DMX Mode (“CHAN: 03”)

4. After you have selected for desired DMX Channel Mode, connect the fixture to any standard DMX

controller via the XLR connections on the fixture and the controller.

Fade Mode:

1. Plug the fixture in and press the MODE button until “FADE RUN SPEED:XX” is displayed. “XX”

represents a number between 01-16.

2. Use the UP and DOWN buttons to find your desired color fade mode.

3. Press the SET UP button and “SPEED:XX” will be displayed. Use the UP and DOWN buttons to

adjust the speed of the color fade.

ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 9

Encore Profile 1000 WW Operating Instructions

System Reset:

This will return the fixture to its factory settings.

1. Plug the fixture in and press the MODE button until “OTHER MODE” is displayed.

2. Press the SET UP button until “SYSRESET” is displayed.

3. Press the UP and DOWN buttons simultaneously to reset, or press the MODE button to exit with-

out making any changes.

Dimmer Curve:

This is used to set the dimming curve used with DMX mode. See the Dimmer Curve Chart section

of this manual for detailed information.

1. Plug the fixture in and press the MODE button until “DMX MODE ADDR:XXX” is displayed.

2. Press the SET UP button until “DELAY:X” is displayed. “X” represents the displayed dimmer

curve (0-4).

• 0 - Standard

• 1 - Stage

• 2 - TV

• 3 - Architectural

• 4 - Theatre

3. Press the UP or DOWN buttons to scroll through and select your desired dimming curve.

DMX State:

This mode defines how the fixture will behave in the event that DMX communication is lost or inter-

rupted. It also determines the mode that the fixture will default to when it is first connected to power.

1. Plug the fixture in and press the MODE button until “DMX MODE ADDR:XXX” is displayed.

2. Press the SET UP button until “DMX MODE NO” is displayed. The current DMX state will be dis-

played.

• “BLACK” (Blackout) - If the DMX signal is lost or interrupted, the unit will automatically go into

stand by mode.

• “HOLD” (Last State) - If the DMX signal is lost or interrupted, the fixture will stay in the last DMX

set up.

• “AUTO” (Auto Run) - If the DMX signal is lost or interrupted, the unit will automatically go into

Auto Run mode.

3. Press the UP or DOWN button to scroll through and select your desired DMX state.

IR Receiver On/Off:

This function is used to activate and deactivate the infared sensor. When this function is acti-

vated you can control the fixture using the ADJ LED RC2 (sold separately), ADJ UC IR (sold sepa-

rately), and Airstream IR app. Please see the ADJ LED RC2 Operation and UC IR & Airstream IR

Functions sections of this manual for remote controls and functions. To control the Encore Profile

1000 WW, plug the included IR receiver into IR receiver input located on the rear of the controller.

You must aim the remote at the IR sensor and be within the maximum operating range of 30 feet.

1. Plug the fixture in and press the MODE button until “OTHER MODE” is displayed.

2. Press the SET UP button until “IR: XX” is displayed.

3. Press the UP or DOWN buttons to either activate the remote function (On) or deactivate it (Off).

ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 10

Encore Profile 1000 WW Operating Instructions

Gamma:

This feature is predominately used when shooting video. Adjust the gamma setting to clean up any

lines that might be seen on camera.

1. Plug the fixture in and press the MODE button until “GAMMA” is displayed. The current gamma

setting will be displayed.

2. Use the UP and DOWN buttons to switch the gamma setting.

Fan Speed:

This will let you set your desired fan speed.

1. Plug the fixture in and press the MODE button until “FAN SPEED” is displayed, and press ENTER.

2. Use the UP and DOWN buttons to switch between the different fan speeds.

Refresh Rate:

This feature is predominately used when shooting video. Adjust the frequency setting to clear up any

LED flicker that might be seen on camera.

1. Plug the fixture in and press the MODE button until “FREQUENC” is displayed. The current fre-

quency setting will be displayed.

2. Use the UP and DOWN buttons to switch the frequency setting.

PCB Temperature:

This will check the current temperature of unit as well as switch between fahrenheit and celsius.

1. Plug the fixture in and press the MODE button until “OTHER MODE” is displayed.

2. Press the SET UP button until “TEM:XXXX” is displayed.

3. Use the UP and DOWN buttons to switch between fahrenheit and celsius.

Encore Profile 1000 WW Focus and Zoom Adjustments

The knobs located on the right side of unit are used to adjust the focus and the zoom. For a tighter/

narrow beam move the first/front knob towards the front of the fixture, and move the second knob

towards the rear. For a wider beam, move the first/front knob towards the middle of the fixture, and

move the second knob towards the middle as well. Adjust accordingly.

Andere Handbücher für Encore Profile 1000 WW

Inhaltsverzeichnis

Andere ADJ Beleuchtungsausrüstung Handbücher

ADJ

ADJ Pro Par56 CWWW Bedienungsanleitung

ADJ

ADJ Flat Par CWWW9 Bedienungsanleitung

ADJ

ADJ FOCUS BEAM LED Bedienungsanleitung

ADJ

ADJ Micro Wash RGBW Bedienungsanleitung

ADJ

ADJ INNO COLOR BEAM QUAD 7 Bedienungsanleitung

ADJ

ADJ Jelly Globe Bedienungsanleitung

ADJ

ADJ Starburst Montageanleitung

ADJ

ADJ MONSTER FUN Bedienungsanleitung

ADJ

ADJ ELIMINATOR Stinger Spot 30 Bedienungsanleitung

ADJ

ADJ SUPER SPOT LED Bedienungsanleitung

ADJ

ADJ Revo Burst Bedienungsanleitung

ADJ

ADJ 3 SIXTY 2R Bedienungsanleitung

ADJ

ADJ LTS-50T Bedienungsanleitung

ADJ

ADJ MOD HEX100 Bedienungsanleitung

ADJ

ADJ H2O IR Bedienungsanleitung

ADJ

ADJ RGB 3C IR Bedienungsanleitung

ADJ

ADJ MEGA PAR PROFILE PLUS Bedienungsanleitung

ADJ

ADJ MIRAGE Q6 PAK Bedienungsanleitung

ADJ

ADJ FOC635 Bedienungsanleitung

ADJ

ADJ COLOR STRAND LED Bedienungsanleitung

ADJ

ADJ ULTRA HEX BAR 12 Bedienungsanleitung

ADJ

ADJ American DJ H2O LED Handbuch

ADJ

ADJ FLAT PAR TW12 Bedienungsanleitung

ADJ

ADJ micro wash wwcw Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung