ADJ FLAT PAR TW5 Bedienungsanleitung

User Manual

FLAT PAR TW5

Rev. 04/2021

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be trade-

marks or registered trademarks of their respective companies and are hereby acknowledged. All

non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera-

tion of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

ADJ Products, LLC - www.adj.com - Flat Par TW5 User Manual Page 2

ADJ Products, LLC - www.adj.com - Flat Par TW5 User Manual Page 3

Unpacking: Thank you for purchasing the Flat Par TW5 by ADJ. Every Flat Par TW5 has been thor-

oughly tested and has been shipped in perfect operating condition. Carefully check the shipping

carton for damage that may have occurred during shipping. If the carton appears to be damaged,

carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit

have arrived intact. In the event that damage has been found or parts are missing, please contact our

toll free customer support number for further instructions. Do not return this unit to your dealer without

rst contacting customer support.

Introduction: The ADJ Flat Par TW5 is part of a continuing pursuit to create high quality intelligent

lighting. The Flat Par TW5 is a DMX intelligent, high powered LED par xture. This xture can be used

in a stand alone mode or connected in a Primary/Secondary conguration. This wash has ve operat-

ing modes: Sound Active mode, Auto mode, RGB mode, Static Color mode, and DMX control mode.

To optimize the performance of this product, please read these operating instructions carefully to

familiarize yourself with the basic operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please keep this manual with the unit for

future reference.

Customer Support: ADJ Products, LLC provides a toll free customer support line, to provide set up

help and to answer any questions should you encounter problems during your set up or initial opera-

tion. You may also visit us on the web at www.adj.com for any comments or suggestions. Service

Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.

Voice: (323) 582-2650

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online visit parts.adj.com.

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or

moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, as

doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

Flat Par TW5 Introduction

ADJ Products, LLC - www.adj.com - Flat Par TW5 User Manual Page 4

Flat Par TW5 Installation

The unit should be mounted using a mounting clamp (not provided) affixed to the mounting bracket

that is provided with the unit. Always ensure that the unit is firmly fixed to avoid vibration and slip-

ping while operating. Always ensure that the structure to which you are attaching the unit is secure

and is able to support at least 10 times the unit’s weight. Also, always use a safety cable that can

hold 12 times the weight of the unit when installing the fixture.

The equipment must be installed by a professional, and it must be installed in a place where it is out

of the reach of people’s grasp.

• Multi-Colors

• Five Operating Modes

• Electronic Dimming 0-100%

• Built in Microphone

• DMX-512 protocol

• 3-Pin DMX Connection

• 6 DMX Modes: 2 Channel Mode, 3 Channel Mode, 4 Channel Mode, 5 Channel Mode, 8 Channel

Mode and 9 Channel Mode.

• ADJ LED RC3 compatiable (Not Included)

• Power Cord Daisy Chain (see the Power Cord Daisy Chain section of this manual)

The Flat Par TW5 carries a 2 year limited warranty. Please fill out the enclosed warranty card to vali-

date your purchase. All returned service items, whether under warranty or not, must be freight pre-

paid and accompanied by a return authorization (R.A.) number. The R.A. number must be clearly writ-

ten on the outside of the return package. A brief description of the problem as well as the R.A. num-

ber must also be written down on a piece of paper included in the shipping carton. If the unit is under

warranty, you must provide a copy of your proof of purchase invoice. You may obtain an R.A. number

by contacting our customer support number. All packages returned to the service department not dis-

playing an R.A. number on the outside of the package will be returned to the shipper.

Flat Par TW5 Warranty Registration

Flat Par TW5 Features

ADJ Products, LLC - www.adj.com - Flat Par TW5 User Manual Page 5

Flat Par TW5 Safety Precautions

• To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken.

• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is

used to reduce the risk of electrical shock and fire in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate with the cover removed.

• Never plug this unit into a dimmer pack.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit if it has been damaged.

• This unit is intended for indoor use only. Use of this product outdoors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in a safe and stable manner.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point at which they exit from

the unit.

• Cleaning - The fixture should be cleaned only as recommended by the manufacturer. See the

Cleaning section of this manual for cleaning details.

• Heat - The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen onto, or liquid has been spilled into, the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a marked change in perfor-

mance.

Flat Par TW5 Set Up

ADJ Products, LLC - www.adj.com - Flat Par TW5 User Manual Page 6

Power Supply: The ADJ Flat Par TW5 contains an automatic voltage switch, which will automati-

cally sense the voltage when it is plugged into the power source. With this switch there is no need to

worry about the correct power voltage, and this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-

nication between intelligent xtures and controllers. A DMX controller sends DMX data instructions

from the controller to the xture. DMX data is sent as serial data that travels from xture to xture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only

have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of dierent manufacturers to be

linked together and operate from a single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using several DMX xtures try to use

the shortest cable path possible. The order in which xtures are connected in a DMX line does not

inuence the DMX addressing. For example, a xture assigned a DMX address of 1 may be placed

anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a xture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that

unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The Flat Par TW5 can be controlled

via DMX-512 protocol. The Flat Par TW5 has 6 DMX channel modes, please see the Operating

Instructions section of this manual for details about DMX modes. The DMX address is set on the

back panel of the Flat Par TW5. Your unit and your DMX controller require a standard 3-pin XLR con-

nector for data input and data output (Figure 1). We recommend Accu-Cable DMX cables. If you are

making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be

purchased at almost all pro lighting stores). Your cables should be made with a male XLR connector

on one end and a female XLR connector on the other. Also remember that DMX cable must be daisy

chained and cannot be split.

ADJ Products, LLC - www.adj.com - Flat Par TW5 User Manual Page 7

Notice: Be sure to follow gures two and three when making your own cables. Do not use the

ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug

or allow the shield conductor to come in contact with the XLR cable’s outer casing. Grounding the

shield could cause a short circuit and erratic behavior.

Special Note: Line Termination. When longer runs of cable are used, you may need to use a termi-

nator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which

is connected between pins 2 and 3 of a male XLR connector (DATA+ and DATA-). This unit is inserted

in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable

terminator (ADJ part number Z-DMX/T) will decrease the chances of erratic behavior.

5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA trans-

mission instead of 3-pin connectors. 5-pin DMX xtures may be implemented in a 3-pin DMX line.

When inserting standard 5-pin data cables in to a 3-pin line, a cable adaptor must be used. These

adaptors are readily available at most electronics stores. The chart below details a proper cable con-

version.

Flat Par TW5 Set Up

Flat Par TW5 Operating Instructions

ADJ Products, LLC - www.adj.com - Flat Par TW5 User Manual Page 8

The display will lock after 30 seconds. Press the MENU button for 3 seconds to unlock.

LED Display On/O:

To set the display press the MODE button until “dXX” is displayed. “XX” represents either “on” or

“oFF” Use the UP or DOWN buttons to select either:

• “don” = LED display on at all times.

• “doFF” = LED display shuts o after 10 seconds.

LED Display Inversion:

Follow these instructions to ip the display 180°.

1. Plug the xture in and press the MODE button until “dXX” is displayed. “XX” represents either

“on” or “oFF”.

2. Press the SET UP button until “Stnd” is displayed.

3. Press the UP or DOWN buttons to reverse the display 180°.

Operating Modes:

The Flat Par TW5 has ve operating modes:

• Sound-Active mode - The unit will react to sound, chasing through the built in programs.

• Static Color Mode - There are 32 colors to choose from.

• Auto Run Mode - There are 3 Auto Modes to choose from.

• WW/CW/A Dimmer Mode - Choose one of the three colors to remain static, or adjust the intensity

of each color to create a custom color.

• DMX control mode - This function will allow you to control individual DMX traits with a standard

DMX 512 controller.

DMX Mode:

Operating through a DMX controller gives the user the freedom to create custom programs tailored

to his or her individual needs. The Flat Par TW5 has 6 DMX modes: 2 Channel mode, 3 Channel

mode, 4 Channel mode, 5 Channel mode, 8 Channel mode, and 9 Channel mode.

1. This function will allow you to control each individual xture’s traits with a standard DMX 512

controller.

2. To run your xture in DMX mode, press the MODE button until “d.XXX” is displayed. “XXX” rep-

resents the address that is currently in use. Use the UP or DOWN buttons to select your desired

DMX address, then press the SETUP button to select your DMX Channel mode.

3. Use the UP and DOWN buttons to scroll through the available DMX Channel Mode options. See

the Channel Mode sections of this manual for detailed descriptions of DMX traits in each DMX

channel mode.

4. After you have chosen your desired DMX Channel mode, link your device to any standard DMX

controller using the XLR connections on your device and your controller.

ADJ Products, LLC - www.adj.com - Flat Par TW5 User Manual Page 9

WW/CW/A Dimmer Mode:

1. Plug the xture in and press the MODE button until one of the following is displayed:

• “H.XXX” for Warm White dimming mode.

• “C.XXX” for Cool White dimming mode.

• “A.XXX” for Amber dimming mode.

2. Press the UP and DOWN buttons to adjust intensity.

3. After you have adjusted the colors to the desired levels, you can then activate strobing by press-

ing the SET UP button.

4. “S.XXX” will be displayed, indicating that the device is in strobing mode. The strobing can be

adjusted between “S.000” (strobe o) to “S.015” (fastest strobe).

Sound Active Mode:

In this mode the Flat Par TW5 will react to sound, and chase through the dierent colors.

1. Plug the xture in and press the MODE button until “So-X” is displayed. “X” represents the sound

active mode (1-8) that is currently in use.

2. The xture will now change via sound.

3. To adjust the sound sensivity, press the SET UP button. “SJ-X” will be displayed. Use the UP or

DOWN buttons to adjust the sensitivity. “SJ-1” is the least sensitive, and “SJ-8” is the most sen-

sitive.

Auto Run Mode:

1. There are 3 Auto Run Modes to choose from: Color Fade, Color Change, and both modes run-

ning together. The running speed is adjustable in all 3 modes.

2. Plug the xture in and press the MODE button until either “AF-X”, “AJ-X”, or “A-JF” is displayed.

• AF-X = Color Fade mode, with 8 Color Fade modes to choose from. Use the UP or DOWN

buttons to scroll through the dierent Auto Fade modes.

• AJ-X = Color Change mode, with 8 Color Change modes to choose from. Use the UP or

DOWN buttons to scroll through the dierent Auto Change modes.

• A-JF = Both Color Fade and Color Change modes running.

3. After you have chosen your desired running mode, press the SET UP button until “SP.XX” is

displayed. When this is displayed you can adjust the running speed of your desired program. Use

the UP or DOWN button to adjust the speed between “SP.01” (slowest) and “SP.16” (fastest).

4. Once you have set your desired running speed, press the SET UP button to return to your desired

Auto Run Mode.

Static Color Mode:

1. Plug the xture in and press the MODE button until “CLXX” is displayed.

2. There are 32 colors to choose from. Select your desired color by pressing the UP and DOWN

buttons. After you have selected your desired color you can activate strobing by pressing the

SET UP button to enter the strobe mode.

3. “S.XXX” will be displayed, indicating that the device is in strobing mode. The strobing can be

adjusted between “S.000” (strobe o) and “S.015” (fastest strobe).

Flat Par TW5 Operating Instructions

ADJ Products, LLC - www.adj.com - Flat Par TW5 User Manual Page 10

Flat Par TW5 Operating Instructions

Default Running Mode:

This is a default running mode. When this mode is activated, all modes will return to their default set-

tings.

1. Plug the xture in and press the MODE button until “dXX” is displayed. “XX” represents either

“on” or “oFF”.

2. Press the SET UP button until “dEFA” is displayed.

3. Press the UP and DOWN buttons simultaneously. Press the MODE button to exit.

ADJ LED RC3:

This function is used to activate or deactivate the ADJ LED RC3 (Remote Control). When this func-

tion is activated, the xture can be controlled using the ADJ LED RC3. Please see the ADJ LED RC3

Operation section of this manual for ADJ LED RC3 controls and functions.

1. Press the MODE button until “dXX” is displayed. “XX” represents either “on” or “oFF”.

2. Press the SET UP button until “IrXX” is displayed. “XX” represents either “on” or “oF”.

3. Press the UP or DOWN buttons to either activate the remote function (On) or deactivate it (O).

DMX State:

This setting denes the behavior of the xture in the event that the DMX signal is lost or interrupted.

It also determines the mode that the xture will default to when it is powered on.

1. Press the MODE button until the DMX address is displayed.

2. Press the SET UP button until “No-X” is displayed. “X” represents a number between 0-2.

3. Use the UP or DOWN buttons to select the operating mode you would like the unit to start up in

when power is applied or the DMX signal is lost.

• “N0-0” (BLACKOUT) - If the DMX signal is lost or power is applied, the unit will automatically

go into stand by mode.

• “N0-1” (HOLD) - If the DMX signal is lost, the xture will stay in the last DMX set up. If power

is applied and this mode is set, the unit will automatically go into the last DMX set up.

• “N0-2” (FADE PROGRAM) - If the DMX signal is lost or power is applied, the unit will auto-

matically run the fade program.

Dimmer Curve:

This is used to set the dimmer curve used with DMX mode. See the Dimmer Curve Chart section of

this manual for more information.

1. Plug the xture in and press the MODE button until the DMX address is displayed.

2. Press the ENTER button until “dr-X” is displayed. “X” represents the current dimming mode.

3. Use the UP and DOWN buttons to nd your desired dimmer curve. Press SET UP when you are

nished.

• dr-0 - Standard

• dr-1 - Stage

• dr-2 - TV

• dr-3 - Architectural

• dr-4 - Theater

Andere Handbücher für FLAT PAR TW5

Inhaltsverzeichnis

Andere ADJ Beleuchtungsausrüstung Handbücher

ADJ

ADJ WOLFMIX WMX1 Bedienungsanleitung

ADJ

ADJ ECO UV BAR DMX Bedienungsanleitung

ADJ

ADJ FOCUS SPOT 2X Bedienungsanleitung

ADJ

ADJ WiFLY EXR QA5 IP Bedienungsanleitung

ADJ

ADJ LTS-50T Bedienungsanleitung

ADJ

ADJ COB CANNON LP200ST Bedienungsanleitung

ADJ

ADJ INNO POCKET SPOT TWINS Bedienungsanleitung

ADJ

ADJ ULTRA GO PAR7X Bedienungsanleitung

ADJ

ADJ Comscan LeD Bedienungsanleitung

ADJ

ADJ Mega QA Go Bedienungsanleitung

ADJ

ADJ Vizi Beam 5R Bedienungsanleitung

ADJ

ADJ Spherion Tri LED Bedienungsanleitung

ADJ

ADJ DMX OPERATOR-I Bedienungsanleitung

ADJ

ADJ PinPoint Go WW Plus Bedienungsanleitung

ADJ

ADJ ACCU-STAND LTS2 AS Bedienungsanleitung

ADJ

ADJ STINGER Bedienungsanleitung

ADJ

ADJ HYDRO SPOT I Bedienungsanleitung

ADJ

ADJ MOD QA60 Bedienungsanleitung

ADJ

ADJ MEGA PAR PROFILE PLUS Bedienungsanleitung

ADJ

ADJ ULTRA BAR 10 PLUS PAK Bedienungsanleitung

ADJ

ADJ 12P HEX PEARL Bedienungsanleitung

ADJ

ADJ Jelly Par Profile System Bedienungsanleitung

ADJ

ADJ Ricochet Bedienungsanleitung

ADJ

ADJ Mega Tri 60 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung