ADJ DMX Operator Bedienungsanleitung

User Instructions

DMX OPERATOR

DMX-512 MIDI

CAPABLE

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be

trademarks or registered trademarks of their respective companies and are hereby acknowledged.

All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of

their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and opera-

tion of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

DOCUMENT VERSION

Please check www.adj.com for the latest revision/update of this guide.

Date Document

Version Notes

01/05/18 1Updated Release

ADJ Products, LLC - www.adj.com - DMX Operator User Manual Page 2

DMX Operator Table of Contents

Introduction

Features / Warranty Registration

Safety Precautions

Controls and Functions

Rear Connections

DMX Addressing

Programming Scenes

Editing Scenes

Programming Chases / Editing Chases

Playback Scenes & Chases

USB Backup / Upload / Firmware

MIDI Operation

Dimensional Drawing

Trouble Shooting

Warranty

Technical Specications

ADJ Products, LLC - www.adj.com - DMX Operator User Manual Page 3

DMX Operator Introduction

Unpacking: Thank you for purchasing the DMX Operator by ADJ Products, LLC. Every DMX Operator

has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the

shipping carton for damage that may have occurred during shipping. If the carton appears to be

damaged, carefully inspect your xture for any damage and be sure all accessories necessary to

operate the unit has arrived intact. In the case damage has been found or parts are missing, please

contact our toll free customer support number for further instructions. Do not return this unit to your

dealer without rst contacting customer support.

Introduction: The ADJ DMX Operator has 12 individual fixture buttons which allow you to control up

to 12 separate intelligent lighting fixtures with up to 16 DMX channels each. With ADJ’s DMX Operator

Controller, you can record up to 6 chanses with separate fade times and step speeds. The 8 individual

channel faders provide you with easy controllability of any DMX fixture. To optimize the performance

of this product, please read these operating instructions carefully to familiarize yourself with the basic

operations of this controller. Please keep this manual with the unit, for future reference.

Customer Support: ADJ provides a customer support line, to provide set up help and to answer any

question should you encounter problems during your set up or initial operation. You may also visit us

on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through

Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.

Voice: (323) 582-2650

Fax: (323) 582-2941

E-mail: support@AmericanDJ.com

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or

moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

doing so will void your manufactures warranty. In the unlikely event your unit may require service

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

DMX Operator Features

• Control up to 192 DMX Channels

• Control up to 12 Separate DMX intelligent lights with up to 16 DMX channels per fixture

• Record up to 6 chases with separate fade times and step speeds

• 8 individual faders

• MIDI controllable

• 3-Pin DMX Connection

• Built-In Microphone

DMX Operator Warranty Registration

The DMX Operator carries a 2 year limited warranty. Please fill out the enclosed warranty card to

validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid

and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the

outside of the return package. A brief description of the problem as well as the R.A. number must also

be written down on a piece of paper included in the shipping carton. If the unit is under warranty, you

must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by contacting

our customer support team on our customer support number. All packages returned to the service

department not displaying a R.A. number on the outside of the package will be returned to the shipper.

ADJ Products, LLC - www.adj.com - DMX Operator User Manual Page 4

ADJ Products, LLC - www.adj.com - DMX Operator User Manual Page 5

DMX Operator Safety Precautions

• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power supply has been frayed or broken.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this controller, if it becomes damaged.

• This unit is intended for indoor use only, use of this product outdoors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point they exit from the unit.

• Heat -The controller should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The controller should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the controller.

C. The controller has been exposed to rain or water.

D. The controller does not appear to operate normally or exhibits a marked change in performance.

E. The controller has fallen and/or subjected to extreme handling.

ADJ Products, LLC - www.adj.com - DMX Operator User Manual Page 6

DMX Operator Controls and Functions

123 4

12 11 10

15 14

DMX Operator Controls and Functions

ADJ Products, LLC - www.adj.com - DMX Operator User Manual Page 7

1. FIXTURE BUTTONS - Used to Select any or all of 12 fixtures. This is what selects which

DMX channels go to the fixtures.

See addressing of fixtures on page 9 for more information

2. SCENE BUTTONS - Used to store Scenes in program mode or playback your scenes in

playback mode

3. LCD DISPLAY - Displays values and settings depending on the chosen function.

4. BANK BUTTONS ( OR )- Selects which Bank you want to use. (there are 30 selectable

banks total.)

5. CHASE - Used to select chases (1-6).

6. PROGRAM - Used to activate program mode. Display blinks when activated.

7. MIDI / REC - Used to control MIDI operation or to Record each step for Scene and

Chases.

8. AUTO/DEL- Select AUTO speed in chase mode or Deletes Scenes and or chases.

9. AUDIO / BANK COPY- Used to trigger sound activation in Chase mode or to copy a bank

of scenes from one to another in Program Mode.

10. BLACKOUT - Disables or enables all channel outputs.

11. TAP SYNC / DISPLAY - In Auto Chase mode used to change rate of chase. Also used to

change LCD Display in Manual Chase.

12. FADE TIME SLIDER - Used to adjust the FADE TIME. Fade Time is the amount of time it

takes the DMX Operator to completely change from one scene to another.

For example; if the fade time slider is set to 0 (zero) a scene change will be instant. If the

slider is set to ‘30s’ it will take the DMX Operator 30 seconds to complete the change

from one scene to the next.

13. SPEED SLIDER - Used to adjust the rate of chase speed in Auto Mode.

14. PAGE SELECT - Used to switch between PAGE A (1-8) & PAGE B (9-16) channel banks.

15. FADERS (1-8) - Used to adjust the channel/values from 0% to 100%.

ADJ Products, LLC - www.adj.com - DMX Operator User Manual Page 8

PUSH

DMX Operator Rear Connections

16 17 18 19

16. MIDI IN - Receives MIDI data.

17. DMX OUT - Used to send DMX signal to fixtures or Packs.

18. USB INTERFACE - This USB INTERFACE has 3 uses:

• Connect a USB LED lamp, with MAX output current of 500mA (Light Not Included).

• Connect a USB stick (not included) and backup all controller settings

(chases/scenes/other settings). You are able to backup 12 files (fixtures 1-12).

Please see page 16 for backup instructions.

• Contact a USB stick (not included) to upload new controller firmware.

NOTE: Please contact ADJ customer support for more details.

19. DC INPUT - Accepts a DC 9~12V, 300 mA minimum, power supply.

ADJ Products, LLC - www.adj.com - DMX Operator User Manual Page 9

DMX Operator DMX Addressing

ADDRESSING FIXTURES

In order to have individual control of each fixture with the DMX Operator, the fixture address-

es should be addressed as follows.

Fixture Button # 1 starts at 1

Fixture Button # 2 starts at 17

Fixture Button # 3 starts at 33

Fixture Button # 4 starts at 49

Fixture Button # 5 starts at 65

Fixture Button # 6 starts at 81

Fixture Button # 7 starts at 97

Fixture Button # 8 starts at 113

Fixture Button # 9 starts at 129

Fixture Button # 10 starts at 145

Fixture Button # 11 starts at 161

Fixture Button # 12 starts at 177

Inhaltsverzeichnis

Andere ADJ Aufnahmegeräte Handbücher

ADJ

ADJ American Audio XEQ-152B Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch