ADT DSC 9047 Bedienungsanleitung
DSC 9047 Quick Guide
https://alpha.adt.com/help/144[11/12/2018 10:33:41 PM]
DSC 9047 - Quick Guide
For a detailed review of the entire system, please view the DSC 9047 manual.
« Help Center
Arm &
Disarm the
System
Battery Bypass
Protected
Areas
Date &
Time
Settings
Chimes &
Beeps
Reset Security
Codes
Trouble
Conditions
Volume
Arm and Disarm
Arm:
To arm all sensors in AWAY mode when you are leaving the premises, press and hold the [AWAY]
key for two seconds or enter your [security code] and exit before the exit delay expires.
To arm all sensors in STAY mode without interior sensors armed, press and hold the [STAY] key for
two seconds or enter your [security code] and do not leave the premises.
Disarm:
To disarm, enter your [security code] before the entry delay expires.
Select
DSC 9047 Quick Guide
https://alpha.adt.com/help/144[11/12/2018 10:33:41 PM]
For more information on this topic please visit the complete DSC 9047 manual.
Battery
The DSC Power Series 9047 operates on the Battery Replacement Page.
Bypass Protected Areas
Bypassing a zone allows you to arm your system with certain protected areas intentionally unarmed or to
access a protected area when the system is armed.
To bypass a zone, enter the function menu by pressing [*]. Press [*] again to reach [Zone Bypass].
Press either [1] or [*], then your [security code].
Enter the zone number to be bypassed or use the [<>] keys to locate the zone number + [*].
When a zone is correctly bypassed, a [B] will appear next to the zone number on the display.
Press [#] to exit.
To unbypass, repeat the bypass procedure or arm and disarm your system.
For more information on this topic please visit the complete DSC 9047 manual.
Change Date and Time
To change the date and time:
Press [*] + [6] + [Master security code] + [1].
Use the [<>] to find the menu [Time and Date] menu option, then press [*] to select.
Enter the minutes and hours in 24 hour format, i.e., 16:45 for 4:45pm.
Enter the date, months, and year in MM:DD:YY format, i.e., 082315 for August, 23, 2015.
Press [#] to exit.
Chimes and Beeps
When your system is in chime mode, a chime alert will sound three tones whenever a protected
door/window is opened.
To turn the door chime function on and off, hold [Chime] for several seconds or press [*] + [4].
For more information on this topic please visit the complete DSC 9047 manual.
Reset
DSC 9047 Quick Guide
https://alpha.adt.com/help/144[11/12/2018 10:33:41 PM]
Return to Top
To clear the display after an alarm event, arm and disarm your system.
Security Codes
You can program up to 16 additional user codes and attributes, however only the Master user can
program user codes and attributes.
To program a new user, press [*] + [5] + [Master security code].
Enter the two digit number to be programmed, i.e., 06 for Access Code 6.
Enter the new user’s new code.
Continue adding additional user codes or press [#] to exit.
To erase an access code, press [*] + [5] + [Master code] + [user access code] + [*].
Press [# to exit.
For a list of user attributes, please view the DSC 9047 manual.
Trouble Conditions
When a Trouble Condition is detected, the word ‘FAULT’ will be displayed on the panel.
To view the Trouble Condition, press [*] + [2] and use the [<>] to scroll.
To silence the Trouble Condition beeps, press [#].
For a list of Trouble Conditions other than CHECK, please see your DSC 9047 manual.
Volume
To adjust the buzzer volume level, press [*] + [6] + [Master code].
Use the [<>] keys to scroll to [Buzzer Control] and then press [*].
Once a volume has been selection, press [#] to save the selection.
How can we help?
Search
Inhaltsverzeichnis
Andere ADT Kamerazubehör Handbücher
