The LED will not flash during transmission if the battery is low. Replace the
battery as follows.
1. Remove the screw from the case back and remove the case back.
2. Insert the blade of a small screwdriver under the battery as shown.
3. Twist the screwdriver to release the battery.
4. With the Positive (+) end of a new battery facing UP, insert the battery as
shown, sliding it under the gold tab, then pressing down to snap into
place.
IMPORTANT: Positive (+) end must face up.
Use Panasonic CR2032, Duracell DL2032, or SENER CR2032 lithium
battery only.
5. Replace the case back and replace the screw to secure the case.
!
Improper installation will result in damage to the battery.
•Do not remove the printed circuit board.
Failure of Replaceable Batteries
This Wireless Key is designed to provide several years of battery life under
normal conditions. The expected battery life is a function of the device
environment, usage and type. Ambient conditions such as high humidity,
high or low temperatures, or large temperature fluctuations may reduce the
expected battery life.
If the batteries need to be replaced, this device reports a low battery
condition to the Base unit as a trouble condition when a button is pressed. In
addition the LED will not flash when a button is pressed. However, if the
device is unused for a long period of time, it may fail to operate as expected.
Regular testing and maintenance will keep the system in good operating
condition for the lifetime of the product.
IMPORTANT! This Wireless Key is intended as a convenience to the user
and should not be considered as a life safety device.
tssc-002-V0
BATTERY
GOLD
TAB
TO REMOVE
BATTERY,
GENTLY SLIDE
SCREWDRIVER
BLADE UNDER
BATTERY HERE
Removing the Battery
REMOVE
SCREW
TO OPEN
CASE
BATTERY
INSTALL WITH POSITIVE (+) SIDE UP.
SLIP BATTERY UNDER GOLD
TAB THEN PRESS DOWN.
IMPORTANT
POSITIVE (+)
SIDE MUST
FACE UP
INSTALL UNDER
GOLD TAB
THEN PRESS
DOWN
Installing the Battery
tssc-003-V0
SPECIFICATIONS
Unit Dimensions: 2.33" x 1.33" x 0.54" (59.2mm x 33.8mm x 14mm)
Battery: 3V, 210mAh, Panasonic CR2032, Duracell DL2032, or
SENER CR2032
WARRANTY INFORMATION
For the latest warranty information, please go to: http://www.security.honeywell.com/hsc/resources/wa
Refer to the Installation Instructions for the TSSC-BASE with which this device is used for limitations of the entire Alarm System.
IMPORTANT SECURITY NOTICE
Please inform the User about the security importance of their wireless key, and what to do if it is lost.
Explain that the wireless key is similar to their keys or access card. If lost or stolen, another person can compromise
their security system. They should immediately notify the Dealer/Installer of a lost or stolen wireless key. The
Dealer/Installer will then remove the wireless key programming from the security system.
FEDERAL COMMUNICATIONS COMMISSION STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the installation Instructions or User's
Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.
FCC/IC STATEMENT
This device complies with Part 15 of FCC Rules, and RSS-210 of IC. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device must accept any interference received, including interference that
may cause undesired operation.
Cet appareil est conforme àla partie 15 des règles de la FCC & de RSS-210 des industries Canada. Son fonctionnement est soumis
aux conditions suivantes: (1) Cet appareil ne doit pas causer d'interférences nuisibles. (2) Cet appareil doit accepter toute
interférence reçue y compris les interférences causant une réception indésirable.
800-13960V2 3/16 Rev. A
ADT Security Services
1501 Yamato Rd
Boca Raton, FL 33431
Copyright © 2013
The FCC ID and IC Certification Number
can be found in the battery compartment.
