Advanced Elements AE2042 Bedienungsanleitung

Inflatable Kayak

Accessory Frame System

Instruction Manual

MODEL AE2042

IMPORTANT!

PLEASE READ THIS MANUAL CAREFULLY BEFORE PROCEEDING. AFTER READING

THIS MANUAL, SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

ADVANCED ELEMENTS, INC. 2011 REV 04-2011

Thank you for your purchase of the Advanced Elements Accessory Frame System!

Simply follow the instructions below to properly install your Accessory Frame.

Once installed, add any aermarket 1” rail mounts and customize with your

choice of rod holders, a sh nder, or other accessories. As an added convenience,

this kit comes with 2 sets of 4 grommets so that you can use your Accessory

Frame on two dierent kayaks or to set up two locations on one kayak.

The Accessory Frame System can be installed on the following Advanced

Elements Models as well as many other boats:

• FireFly: AE1020

• Lagoon 1: AE1031/DragonFly: AE1001 and AE1021

• Lagoon 2: AE1033/DragonFly 2: AE1003 and AE1023

• All AdvancedFrame Models: AE1017, AE1012, AE1009, AE1007

• StraitEdge Kayak: AE1006

• StraitEdge 2 Kayak: AE1014

If you do not have an Advanced Elements kayak, make sure to measure

your specic boat for proper t: the layout paern is 22” wide for the

front grommets and 23” wide for the rear grommets.

Items included in this package:

• Accessory Frame

• 8 Mounting Grommets (2 sets of 4 for multiple applications)

• 2 tubes of Application Glue

• 1 Plastic Cuing Mat

• Instructions with Mounting Templates

GROMMET APPLICATION FOR THE FOLLOWING AE MODELS:

• FireFly

• Lagoon 1 and 2

• DragonFly 1 and 2

• All AdvancedFrame models.

For this application you will need the following items from this package:

• 4 Mounting Grommets

• Application Glue

• Plastic Cuing Mat

• Both Mounting Templates

Additional Items you will need for proper installation:

• Exacto or Mae Knife with a new blade

• Fabric chalk or pencil

• Metal straight edge ruler

• Scotch Tape and Duct Tape

• 4 small sheets of cardboard approx. 5”x”5 in size

Your Accessory Frame should be in three parts (the main frame body,

and 2 detachable arms). Before starting, inate your kayak so that you

can have it ready for positioning the Accessory Frame and for gluing the

Mounting Grommets into place.

Positioning the Mounting Grommets:

1. Slide two of the Mounting Grommets onto the main Frame Body and

position them so that they are just past the holes in the frame.

SEE IMAGE 1.

2. Slide one Mounting Grommet onto each of the Detachable Arms and

position them so that they are at the same end of the arm as the black

pole cap. SEE IMAGE 2.

Image 1

Accessory Frame System Instruction Manual

Image 2

3. Once the Mounting Grommets are in place, aach the Frame Arms

to the Frame Body.

4. Place the assembled Accessory Frame (with the Mounting Grommets

in place) on a at surface and rotate the Mounting Grommets so that

the disk portion of each grommet lays at and even on the surface.

Continued on Next Page

6. With the Mounting Grommets still on the Accessory Frame, locate

the two Mounting Templates included with these instructions and

place them underneath the grommets, aligning the circular shapes

on the templates with the disk portion of the grommets. Align the

front grommets rst (these are the grommets nearest to the push

buons on the frame assembly), then slide the rear grommets (these

are the grommets on the detachable arms) as needed to align them

with the other set of circles on the templates.

7. Once you have aligned the grommets on the Mounting Templates,

use your scotch tape to tape the templates into place under the

grommets. Be sure to tape the templates to the grommets so that you

will be able to peel the tape up later without damaging the templates,

trust us, this will be important later.

8. Now that the templates are in place, position the Accessory Frame

where you would like it on your kayak and rotate the grommets as

necessary to conform to the contours of the boat. Use a pencil or fabric

chalk to mark the corner edges of the templates onto your boat.

NOTE: The Accessory Frame should be placed with the ends of the

frame arms facing towards the cockpit of the kayak.

NOTE: When placing your Accessory Frame on your kayak, keep in

mind your paddle stroke (so the frame will not get in the way),

reachability from the cockpit, and any potential positioning that may

prevent you from easily entering and exiting your kayak.

9. Aer marking the edges of the Mounting Templates on your boat,

separate the templates from the grommets and re-align the templates

with the markings on your boat. Use your pencil/chalk to mark the

position of the two rectangles in the middle of the templates onto the

deck of your boat and remove the templates.

10. Use your Exacto/Mae knife to cut out the marked rectangles on the

deck of your kayak.

NOTE: Place the Plastic Cuing Mat that has been supplied with this

kit under the deck of the kayak and position it under each of the

rectangles as you cut them out. Make sure that the Cuing Mat is

in-between the outer cover and the main tube of the kayak.

Accessory Frame System Instruction Manual

Aer Cuing the openings for the Mounting Grommets, position each

Mounting Grommet so that it is popping up through the newly cut

openings from the underside of the deck of the kayak. SEE IMAGE 3.

Install the Accessory Frame by inserting the Fame Body and the Detachable

Arms through the grommets and connecting all parts. This will ensure

proper placement before gluing the Mounting Grommets in place.

Gluing the Mounting Grommets:

Aer ensuring proper t and alignment of the Mounting Grommets,

remove the Accessory Frame, set it aside, and pull all of the grommets

out of their newly cut holes.

1. Place your four sheets of cardboard on the inside of your kayak deck

and position them under each of the newly cut rectangular grommet

holes.

2. Starting with ONE Mounting Grommet at a time: In a well-ventilated

area, apply enough glue to the top side of the Mounting Grommet disk

to spread around so that the glue is evenly applied on the disk.

3. Position the Mounting Grommet so that it is popping up through the

newly cut hole in the deck of your kayak, SEE IMAGE 3. Make sure

you have your cardboard in place. Place your hand underneath the

sheet of cardboard to ensure that it is in contact with the boom of

the grommet and apply pressure to aen out the grommet disk

while making sure that the disk is in full contact with the deck material

of the kayak.

4. Once you have good contact between the deck material of the kayak

and the Mounting Grommet, remove your hand from under the

cardboard and proceed to apply duct tape around the perimeter of

the grommet hole on the outside of the kayak. Apply the duct tape

so that it aens out the material around the base of the grommet

meanwhile ensuring good contact between the material and the

grommet disk. SEE IMAGE 4.

Image 3 Image 4

Continued on Next Page

5. Repeat steps 2-4 for the next three Mounting Grommets.

6. Aer gluing and taping all four Mounting Grommets, leave the glue to

cure for at least 12 hours before installing the Accessory Frame for use.

7. Once the glue has dried, remove the duct tape, install the Accessory

Frame, and you are ready to go!

-------------------------------------------------------------------------------------------------

GROMMET APPLICATION FOR THE FOLLOWING AE MODELS:

• StraitEdge 1

• StraitEdge 2

You can use this application method for other PVC inatables (where

you will need to glue to the outer PVC skin), as well as many hard-shell

kayaks. For hard-shells, check with the manufacturer for the appropriate

glue to use.

For this application you will need the following items from this package:

• 4 Mounting Grommets

• Application Glue

• Both Mounting Templates

Additional Items you will need for proper installation:

• Exacto or Mae Knife with a new blade

• Pencil

• Duct Tape

Accessory Frame System Instruction Manual

Before starting, inate your kayak so that you can have it ready for

positioning the Accessory Frame and for gluing the Mounting Grommets

into place.

1. Important: Begin by using your Exacto/Mae knife to cut a small notch

in to each of your 4 Mounting Grommets. This notch will be used to

mark for proper alignment of the grommets when gluing. SEE IMAGE 5.

Image 5

2. Slide two of the Mounting Grommets onto the main Frame Body and

position them so that they are just past the holes in the frame.

SEE IMAGE 1.

3. Slide one Mounting Grommet onto each of the Detachable Arms and

position them so that they are at the same end as the black pole cap.

SEE IMAGE 2.

4. Once the Mounting Grommets are in place, aach the Frame Arms

to the Frame Body and place the assembled Accessory Frame (with

the Mounting Grommets in place) on a at surface and rotate the

Mounting Grommets so that the disk portion of each grommet lays

at and even on the surface.

5. Locate the two Mounting Templates included with these instructions

and place them underneath the grommets, aligning the circular shapes

on the templates with the disk portion of the grommets. Align the front

grommets rst (these are the grommets nearest to the push buons on

the frame assembly), then slide the rear grommets (these are the

grommets on the detachable arms) as needed to align them with the

other set of circles on the templates; this will ensure proper spacing

between the two grommets on each side of the frame.

6. Position the Accessory Frame where you would like it on your kayak

and rotate the grommets as necessary to conform to the contours of

the boat. Use a pencil to trace around the disk portion of the four

Mounting Grommets. NOTE: Make sure to also mark the notches that

you cut into the grommets in step 1, this is very important for proper

alignment of the grommets when gluing them to your boat!

NOTE: The Accessory Frame should be placed with the ends of the

frame arms facing towards the seating position of the kayak.

NOTE: When placing your Accessory Frame on your kayak, keep in

mind your paddle stroke (so the frame will not get in the way), and

any potential positioning that may prevent you from easily entering

and exiting your kayak.

7. Once you have marked the Mounting Grommet placement on your

boat, remove the grommets from the Accessory Frame and set the

Accessory Frame aside.

8. Starting with ONE Mounting Grommet at a time: In a well-ventilated

area, apply enough glue to the boom side of the Mounting Grommet

disk to spread around so that the glue is evenly applied on the disk.

9. Choose one of the four marked out grommet placements on your

kayak, apply a thin layer of glue and spread it around to cover the

marked out area. Proceed to apply the Mounting Grommet to the

surface of the kayak, making sure that you have aligned the notch in

your grommet to the notch mark that you made on the kayak.

10. Apply constant pressure for a few minutes to allow for the glue to set.

11. Apply duct tape around the perimeter of the grommet. Make sure to

apply the duct tape so that it aens out the grommet disk.

12. Repeat steps 7-11 for the next three Mounting Grommets.

13. Aer gluing and taping all four Mounting Grommets, leave the glue

to cure for at least 12 hours before installing the Accessory Frame for use.

14. Once the glue has dried, remove the duct tape, install the Accessory

Frame, and you are ready to go!

Accessory Frame System Instruction Manual

Installing the Accessory Frame on your kayak:

Once the glue on your Mounting Grommets has dried, follow these steps

for installing your Accessory Frame for use.

1. Make sure that the Accessory Frame is in 3 parts. If the Accessory

Frame is assembled:

I. Locate the push-buons at the sockets of the Detachable Arms.

II. Depress the push-buons and separate the Detachable Arms from

the Frame Body.

2. Once you have the Accessory Frame in 3 parts, slide the Detachable

Arms through the grommets located at the front of the kayak. Make

sure that the push-buon sockets are pointed to the front of the kayak.

(See Illustrations 1 and 2)

3. Socket the Frame Body onto the Detachable Arms. Make sure that the

push-buons pop up through the holes on the Frame Body. At this

same time, make sure that the push-buons are positioned in between

the two grommets, not in front of the forward grommets.

(See Illustrations 1 and 2)

4. To remove the Accessory Frame, press the push-buons in at the sockets

and separate the Frame Body from the Detachable Arms, then slide

the Detachable Arms out of the grommets.

Frame Body

Detachable Arm

Illustration 1

Frame Body

Detachable Arm

Illustration 2

Andere Advanced Elements Boot Handbücher

Advanced Elements

Advanced Elements STRAITEDGE AE1006 Owner's Bedienungsanleitung

Advanced Elements

Advanced Elements Firefly AE1020 Bedienungsanleitung

Advanced Elements

Advanced Elements STRAITEDGE AE1006 Owner's Bedienungsanleitung

Advanced Elements

Advanced Elements AdvancedFrame AE1012 Bedienungsanleitung

Advanced Elements

Advanced Elements DRAGONFLY AE1001 Bedienungsanleitung

Advanced Elements

Advanced Elements AE2040 Bedienungsanleitung

Advanced Elements

Advanced Elements Packlite Inflatable Kayak AE3021 Bedienungsanleitung

Advanced Elements

Advanced Elements STRAITEDGE2 PRO Bedienungsanleitung

Advanced Elements

Advanced Elements Sland Voyage 2 AE3023 Bedienungsanleitung

Advanced Elements

Advanced Elements ATTACK PRO Bedienungsanleitung

Advanced Elements

Advanced Elements Packlite Inflatable Kayak AE3021 Bedienungsanleitung

Advanced Elements

Advanced Elements AirFusion AE1040-Y Bedienungsanleitung

Advanced Elements

Advanced Elements Lagoon2 AE1033 Bedienungsanleitung

Advanced Elements

Advanced Elements AdvancedFrame AE1017 Bedienungsanleitung

Advanced Elements

Advanced Elements ADVANCEDFRAME ELITE Bedienungsanleitung

Advanced Elements

Advanced Elements AdvancedFrame AE1012 Bedienungsanleitung

Advanced Elements

Advanced Elements StraitEdge Kayak Bedienungsanleitung

Advanced Elements

Advanced Elements AE1009-XE Bedienungsanleitung

Advanced Elements

Advanced Elements StraitEdge AE1008 Bedienungsanleitung

Advanced Elements

Advanced Elements AIRFUSION EVO AE1042 Bedienungsanleitung

Advanced Elements

Advanced Elements ADVANCEDFRAME SPORT Bedienungsanleitung

Advanced Elements

Advanced Elements AdvancedFrame AE1007 Bedienungsanleitung

Advanced Elements

Advanced Elements Lagoon1 AE1031 Bedienungsanleitung

Advanced Elements

Advanced Elements StraitEdge AE1006-ANG Bedienungsanleitung

Beliebte Boot Handbücher anderer Marken

Raymarine

Raymarine ST70 Instrument Bedienungsanleitung

Jeanneau

Jeanneau CAP CAMARAT 8.5 CC Bedienungsanleitung

Tiara Yachts

Tiara Yachts C49 2024 Bedienungsanleitung

J 105 Bedienungsanleitung

Monterey Boats

Monterey Boats Sport Yacht 330 Bedienungsanleitung

PURSUIT

PURSUIT OS 335 Bedienungsanleitung

Boston Whaler

Boston Whaler CONQUEST 345 Bedienungsanleitung

Jeanneau

Jeanneau SUN ODYSSEY 41 DS Bedienungsanleitung

Meridian

Meridian 490 Pilothouse Bedienungsanleitung

Robo Marine Indonesia

Robo Marine Indonesia GEOMAR Bedienungsanleitung

Swallow Boats

Swallow Boats BayRaider Bedienungsanleitung

Intex

Intex Excursion 5 Set Bedienungsanleitung

X SHORE

X SHORE EELEX 8000 Bedienungsanleitung

ISLAND PACKET

ISLAND PACKET 370 Bedienungsanleitung

Sea Ray

Sea Ray 175 Sport Bedienungsanleitung

Regal

Regal 2300 Bedienungsanleitung

Mercury

Mercury Sport 220/240 Bedienungsanleitung

Marquis

Marquis 720 FLY Bedienungsanleitung