Advantech PCA-6178 Bedienungsanleitung

PCA-6178

Full-size socket 370 Intel®

Pentium®III

processor-based

PCI/ISA-bus CPU card

This document is copyrighted, 2000, by Advantech Co., Ltd. All

rights are reserved. Advantech Co., Ltd. reserves the right to make

improvements to the products described in this manual at any time

without notice.

No part of this manual may be reproduced, copied, translated or

transmitted in any form or by any means without the prior written

permission of Advantech Co., Ltd. Information provided in this

manual is intended to be accurate and reliable. However, Advantech

Co., Ltd. assumes no responsibility for its use, nor for any in-

fringements upon the rights of third parties which may result from its

use.

Acknowledgements

• AWARD is a trademark of AWARD Software, Inc.

• IBM and PC are trademarks of International Business Machines

Corporation.

• Intel and Celeron are trademarks of Intel Corporation.

• MS-DOS is a trademark of Microsoft Corporation.

• SMC is a trademark of Standard Microsystems Corporation.

• WinBond is a trademark of Winbond Corporation.

• SYMBIOS is a registered trademark of Symbios, Inc.

• ATI is a registered trademark of ATI Technologies, Inc.

All other product names or trademarks are the properties of their

respective owners.

Part No. 2006617801

2nd Edition Printed in Taiwan Jan. 2001

A Message to the Customer

Advantech customer services

Each and every Advantech product is built to the most exacting

specifications to ensure reliable performance in the harsh and

demanding conditions typical of industrial environments. Whether

your new Advantech equipment is destined for the laboratory or the

factory floor, you can be assured that your product will provide the

reliability and ease of operation for which the name Advantech has

come to be known.

Your satisfaction is our primary concern. Here is a guide to

Advantech’s customer services. To ensure you get the full benefit of

our services, please follow the instructions below carefully.

Technical support

We want you to get the maximum performance from your products.

So if you run into technical difficulties, we are here to help. For the

most frequently asked questions, you can easily find answers in your

product documentation. These answers are normally a lot more

detailed than the ones we can give over the phone.

So please consult this manual first. If you still cannot find the answer,

gather all the information or questions that apply to your problem, and

with the product close at hand, call your dealer. Our dealers are well

trained and ready to give you the support you need to get the most

from your Advantech products. In fact, most problems reported are

minor and are able to be easily solved over the phone.

In addition, free technical support is available from Advantech

engineers every business day. We are always ready to give advice on

application requirements or specific information on the installation

and operation of any of our products.

elbatnosirapmoc1B00-seireS8716-ACP

ledoM 1B00-V8716-ACP1B00-EV8716-ACP1B00-SV8716-ACP1B00-F8716-ACP1B00-L8716-ACP

:UPC letnI

muitneP

™noreleC/III

073tekcos

!! !!

✓

:tespihcmetsyS letnI

XB044 !! !!

✓

:SOIB SOIBhsalFP&PdrawA !! !!

✓

:ehcac2L )UPCno(BK821 !! !!

✓

:MARmetsys.xaM BM867 )stekcosMMIDnip-861x3( !! !!

✓

:evirDhgiHASI Am46otpU !! !!

✓

tropBSU !! !!

✓

srotcennocEDIE2 !! !!

✓

:ksidetatsdiloS 'smetsyS-MstroppuS

COD

BM441otpuksidhsalF0002 !! !!

✓

stroplellarap1,laires2 !! !!

✓

:AGV )LX™EGARD3ITA(AGV/PGA !! !!

:NAL tenrehtET-esaB001/01

letnI(

)tespihc95528 -!-!-

:ISCS ISCS2artlUICPtib-23 )tespihc598C35SOIBMYS( --!!

MARAGV BM4BM4BM4BM4-

elbatnosirapmoc1B20-seireS8716-ACP

ledoM 1B20-V8716-ACP1B20-EV8716-ACP1B20-SV8716-ACP1B20-F8716-ACP

:UPC letnI

muitneP

™noreleC/III

073tekcos

!! !!

:tespihcmetsyS letnI

XB044 !! !!

:SOIB SOIBhsalFP&PdrawA !! !!

:ehcac2L )UPCno(BK821 !! !!

:MARmetsys.xaM BM867 )stekcosMMIDnip-861x3( !! !!

:evirDhgiHASI Am46otpU !! !!

tropBSU !! !!

srotcennocEDIE2 !! !!

:ksidetatsdiloS 'smetsyS-MstroppuS

COD

BM441otpuksidhsalF0002 !! !!

stroplellarap1,laires2 !! !!

:AGV )LX™EGARD3ITA(AGV/PGA !! !!

:NAL tenrehtET-esaB001/01

letnI(

)tespihc95528 -!-!

:ISCS ISCS2artlUICPtib-23 )tespihc598C35SOIBMYS( --!!

MARAGV BM8BM8BM8BM8

Product warranty

Advantech warrants to you, the original purchaser, that each of its

products will be free from defects in materials and workmanship for

one year from the date of purchase.

This warranty does not apply to any products which have been

repaired or altered by persons other than repair personnel authorized

by Advantech, or which have been subject to misuse, abuse, accident

or improper installation. Advantech assumes no liability under the

terms of this warranty as a consequence of such events.

If an Advantech product is defective, it will be repaired or replaced at

no charge during the warranty period. For out-of-warranty repairs,

you will be billed according to the cost of replacement materials,

service time and freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For

example, type of PC, CPU speed, Advantech products used, other

hardware and software used, etc.) Note anything abnormal and list

any on-screen messages you get when the problem occurs.

2. Call your dealer and describe the problem. Please have your

manual, product, and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return

material authorization) number from your dealer. This allows us to

process your return more quickly.

4. Carefully pack the defective product, a fully-completed Repair and

Replacement Order Card and a photocopy proof of purchase date

(such as your sales receipt) in a shippable container. A product

returned without proof of the purchase date is not eligible for

warranty service.

5. Write the RMA number visibly on the outside of the package and

ship it prepaid to your dealer.

Initial Inspection

Before you begin installing your card, please make sure that the

following materials have been shipped:

• 1 PCA-6178 socket 370 Pentium III®/ Celeron™ processor-based

single board computer

• 1 Pentium III®/Celeron™ processor (optional)

• 1 cooling fan

• 1PCA-6178User'sManual

• 1CDdriveutility

• 4 SCSI driven disks (optional)

• 1FDDcable

• 2EIDEHDDcables

• 1 printer (parallel port) cable

• 1 ATX-to-PS/2 power cable

• 1 ivory cable for PS/2 keyboard and PS/2 mouse

• 1SCSI cable(optional,P/N 1701060000)

• 1USB cable(optional,P/N 1700100170)

If any of these items are missing or damaged, contact your distributor

or sales representative immediately.

We have carefully inspected the PCA-6178 mechanically and

electrically before shipment. It should be free of marks and scratches

and in perfect working order upon receipt.

As you unpack the PCA-6178, check it for signs of shipping damage.

(For example, damaged box, scratches, dents, etc.) If it is damaged or

it fails to meet the specifications, notify our service department or

your local sales representative immediately. Also notify the carrier.

Retain the shipping carton and packing material for inspection by the

carrier. After inspection, we will make arrangements to repair or

replace the unit.

Contents

Chapter 1 Hardware Configuration.............................. 1

1.1 Introduction........................................................................2

1.2 Features...............................................................................3

1.3 Specifications ......................................................................5

1.3.1 System.........................................................................5

1.3.2 Memory.......................................................................5

1.3.3 Input/Output ................................................................6

1.3.4 VGA interface .............................................................6

1.3.5 SCSI interface .............................................................6

1.3.6 Ethernet LAN (PCA-6178E/6168F only) ...................6

1.3.7 Solid state disk ............................................................6

1.3.7 Industrial features .......................................................7

1.3.8 Mechanical and environmental specifications............7

1.4 Board Layout: Main Features ..........................................8

1.5 Jumpers and Connectors...................................................9

1.6 Board Layout: Jumper and Connector locations ........11

1.7 Safety Precautions............................................................12

1.8 Jumper Settings................................................................13

1.8.1 How to set jumpers ...................................................13

1.8.2 CPU clock ratio setting (SW1) .................................13

1.8.3 CPU type select (SW2) .............................................14

1.8.4 CMOS clear (J1) .......................................................15

1.8.5 Watchdog timer output (J2) ......................................15

1.8.6 DiskOnChip® 2000 Flash disk address select (J3)...16

1.9 System Memory................................................................18

1.9.1 Sample calculation: DIMM memory capacity..........18

1.9.2 Supplementary information about DIMMs ..............19

1.10 Memory Installation Procedures ....................................20

1.11 Cache Memory .................................................................20

1.12 CPU Installation...............................................................21

Chapter 2 Connecting Peripherals ............................ 23

2.1 Primary (CN1) and Secondary (CN2) IDE Connectors24

2.2 Floppy Drive Connector (CN3).......................................25

2.3 Parallel Port (CN4) ..........................................................25

2.4 SCSI Connector (CN5) ....................................................26

2.5 USB Port (CN6) ................................................................27

2.6 VGA Connector (CN7) ....................................................27

2.7 10/100Base-T Ethernet Connector (CN8) ......................28

2.8 Serial Ports (CN9: COM1; CN10: COM2)....................28

2.9 PS/2 Keyboard and Mouse Connector (CN11) .............29

2.10 External Keyboard Connector (CN12) ..........................29

2.11 Infrared (IR) Connector (CN13) ....................................30

2.12 CPU Fan Connector (CN14) ...........................................30

2.13 Front Panel Connectors (CN16, CN17, CN18, CN19 and

CN21).................................................................................31

2.13.1 Keyboard lock and power LED (CN16) .................31

2.13.2 External speaker (CN17).........................................31

2.13.3 Reset (CN18)...........................................................31

2.13.4 HDD LED (CN19) ..................................................32

2.13.5 ATX soft power switch (CN21)..............................32

2.14 ATX Power Control Connectors (CN20 and CN21).....32

2.14.1 ATX feature connector (CN20) and soft power

switch connector (CN21) ...................................................32

2.14.2 Controlling the soft power switch...........................33

Chapter 3 Award BIOS Setup ..................................... 35

3.1 Introduction......................................................................36

3.2 Entering Setup..................................................................36

3.3 Standard CMOS Setup....................................................37

3.3.1 CMOS RAM backup.................................................37

3.4 BIOS Features Setup .......................................................38

3.4.1 Virus Warning...........................................................38

3.4.2 Quick Power On Self Test ........................................39

3.4.3 Boot Sequence...........................................................39

3.4.4 Boot Up Floppy Seek ................................................40

3.4.5 Boot Up NumLock Status .........................................40

3.4.6 Gate A20 Option .......................................................40

3.4.7 Typematic Rate Setting.............................................40

3.4.8 Typematic Rate (Chars/Sec) .....................................40

3.4.9 Typematic Delay (msec) ...........................................41

3.4.10 Security Option .......................................................41

3.4.11 PCI/VGA Palette Snoop..........................................41

3.4.12 OS Select for DRAM > 64MB................................41

3.4.13 Video BIOS Shadow ...............................................41

3.4.14 C8000-CBFFF Shadow / DC000-DFFFF Shadow .42

3.5 Chipset Features Setup....................................................42

3.5.1 SDRAM RAS to CAS Delay ....................................43

3.5.2 SDRAM RAS Precharge Time .................................43

3.5.3 SDRAM CAS Latency Time ....................................43

3.5.4 DRAM Data Integrity Mode .....................................43

3.5.5 16 Bit I/O Recovery Time / 8 Bit I/O Recovery.......43

3.5.6 Memory Hole At 15M-16M .....................................43

3.5.7 AGP Aperture Size (MB)..........................................44

3.6 Power Management Setup ..............................................44

3.6.1 Power Management ..................................................44

3.6.2 HDD Power Down ....................................................44

3.6.3 Soft-Off by PWR-BTTN...........................................45

3.7 PCI Configuration Setup.................................................45

3.7.1 IRQ-xx assigned to : PCI/ISA PnP ...........................45

3.7.2 DMA-x assigned to : PCI/ISA PnP...........................46

3.7.3 Used MEM base addr : N/A......................................46

3.8 Load BIOS Defaults .........................................................46

3.9 Load Setup Defaults.........................................................46

3.10 Integrated Peripherals.....................................................47

3.10.1 IDE HDD Block Mode ...........................................47

3.10.2 IDE Primary Master/Slave PIO/UDMA Mode,

IDE Secondary Master/Slave PIO/UDMA Mode (Auto) ..47

3.10.3 On-Chip PCI IDE Primary/Secondary....................47

3.10.4 Onboard FDC Controller ........................................48

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Advantech Computerhardware Handbücher

Advantech

Advantech PCA-6186 Bedienungsanleitung

Advantech

Advantech PCA-6742 Series Bedienungsanleitung

Advantech

Advantech PCA-6743 Installations- und Betriebshandbuch

Advantech

Advantech PCE-GIGE2 Installations- und Betriebshandbuch

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Advantech

Advantech ASMB-831 Series Installations- und Betriebshandbuch

Advantech

Advantech PCLD-8811 Installations- und Betriebshandbuch

Advantech

Advantech MIO-2363 Bedienungsanleitung

Advantech

Advantech PCM-4153 Bedienungsanleitung

Advantech

Advantech PCE-7B13-0AA1 Installations- und Betriebshandbuch

Advantech

Advantech ASMB-610V3 Installations- und Betriebshandbuch

Advantech

Advantech ACP-2020G Bedienungsanleitung

Advantech

Advantech PCE-3026 Installations- und Betriebshandbuch

Advantech

Advantech PCA-6190 Bedienungsanleitung

Advantech

Advantech MIO-2375 Installations- und Betriebshandbuch

Advantech

Advantech PCIE-1730H Installations- und Betriebshandbuch

Advantech

Advantech PCA-6742 Series Bedienungsanleitung

Advantech

Advantech AiMC-2000 Bedienungsanleitung

Advantech

Advantech AMAX-4817 Installations- und Betriebshandbuch

Advantech

Advantech MIO-4370 Bedienungsanleitung

Advantech

Advantech PCA-6740 Bedienungsanleitung

Advantech

Advantech IDK-2119 Series Bedienungsanleitung

Advantech

Advantech PCL-734 Bedienungsanleitung

Advantech

Advantech MIC-710AIL Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung