Advent CADNAV1 Bedienungsanleitung

CADNAV1 Advent Integrated Navigation

This interface is designed to integrate Navigation into select

Cadillac CUE, Buick, Chevrolet and GMC MyLink Systems.

This system is NOT applicable to vehicles that do not have

CUE or MyLink/Intelilink and will not operate in those

vehicles.

INSTALLATION GUIDE

What’s in the Box

The following items are supplied with the CADNAV1

• LVDS Video Cable

#31414170

• Aux Audio # 31514170

• CAN Module #33814170

• GPS Antenna #34914170

• CAD Power Harness #37514170 • USB Update Cable #32714170

• Buick Power Harness #37614170 • Map SD Card #35014170

• CAN to NAV

#30314170 • Speaker Wire Harness #31914170

• Switch

#34714170 • AUX Video #33914170

• Installation Guide

• External Speaker #33514190

NOTE: Not all parts are used in every installation.

Prior to Installation:

Care must be taken when installing this accessory to ensure damage does not occur to the vehicle.

The installation of this accessory should follow approved guidelines to ensure a quality installation.

Read entire instructions thoroughly before starting.

This document covers such items as:-

• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).

• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).

• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.)

NOTES:

Removed Parts:

Inspect the vehicle for any damage.

Place all removed parts on a protected surface in an area where they will not be damaged.

Connectors:

When disconnecting connectors, do not pull on the wires; pull on the connectors.

Vehicle Preparation and Protection

CAUTION!

• Do not touch the positive terminal with any tool when removing cable.

• Be sure ignition key is in the OFF position during install

• Do not disconnect ANY airbag connectors or indicators. Doing so may result in activating a diagnostic code. These codes

will require the dealer to perform the reset procedure and may be charged a dealer fee.

• If you are unsure of any vehicle trim removal process consult the OEM service manual.

• Removing vehicle trim panels in extreme hot and cold climate could result in some vehicle damage. Use care when

removing all vehicle trim.

• Using tape on vehicle trim panels could help limit any scratches and or marring. Use plastic trim panel removal tools

whenever possible.

The instructions included in this kit are current at the time of printing. It is designed as a guide to help make the

installation of this product successful. Always use caution and ask for assistance if you are not sure how to proceed.

Voxx International is not responsible for any damage that may occur during installation or any changes to the vehicle

interior.

Installation:

Removal of the Radio control center is required for installation. Vehicle Specic instructions are available on-line at www.

voxxuniversity.com.

After the components are removed, connect the following:

1. The navigation module can be located behind the radio or to either side. Determine your exact mounting location to insure

you route your wires correctly.

2. Using the supplied T-harness power cable, disconnect the matching

cable from the rear of the main radio unit. Plug the T-harness in

the radio and the factory harness into the T-harness. (Yellow arrow).

3. Disconnect the USB type video cable from the rear of the radio.

(Red arrow). Plug the supplied LVDS cable in to the radio and the

factory cable into the LVDS cable. Connect the LVDS cable to the

Nav module.

Cadillac CUE system Shown above

NOTE: The Buick, GMC radio panel will look dierent than the picture above but the connections are the same.

4. Connect the CAN module to the power harness connection.

5. Connect the CAN to Nav interface cable to the main Nav module as shown in the wiring diagram.

6. The system utilizes either the center front speaker in the dash or an included external

speaker for easier installation or for vehicles that do not have a center channel speaker.

The Nav system will mute the radio audio in that speaker only when giving directions.

NOTE: The left dash speaker will also work if no center speaker is available.

To install using the factory speaker, remove the center channel speaker from the dash,

route the included speaker harness to the speaker location. Connect the supplied harness

to the speaker and the OEM wiring to the other harness connector. Route the wire to the

module and connect.

If using the included External speaker pick a location that is not obstructed and can be

heard easily by the driver. Remove the tape backing from the rear of the speaker and

attach to the mounting location. Route the wire to the module and connect.

• If needed or for custom installation this can be wired to any standard 4 ohm

speaker. The Green and Gray colored wires are the audio output.

The Nav module has the ability to add a backup camera and 2 AV inputs. The module

will support the factory backup camera if the vehicle is equipped with this.

If you are adding a camera or aux inputs, use the supplied cables and connect as needed.

7. Aux Video: 8. Aux Video: Aux Audio:

Red: Backup Camera Input See attached labels

Yellow: Aux 1 Video Input

White: Aux 2 Video Input

Gray: Not used

9. USB Update Cable: This is used for map updates. Route the cable from the

module to the glove box for future use as needed. Connect to the Nav module.

10. GPS Antenna: The antenna must be mounted in a location where it has a clear view of the sky. Center of the dash by the glass is

recommended.

NOTE: If reception is poor re-locate to another area and re-test. The GPS antenna cannot be blocked by metal surfaces

and should be visible for best reception.

11. Nav activation switch: In Cadillac vehicles with CUE, the nav is activated by pressing the NAV icon on-screen. In other vehicles

the nav will be activated by pressing a set position on the screen or using the included wired switch. If using the switch nd

a proper location for the switch to be mounted and then route the wire to the Nav Module. Note: The switch also allows

switching through the AUX inputs if they are utilized.

DIP Switch Settings:

Up is OFF; Down is ON for Dip Switches.

12. Check the DIP Switch settings:

Dip 1: UP External RGB input-Not Used

Dip 2: UP Video Input 1 O

Dip 3: UP Video Input 2 O

Dip 4: DOWN High Resolution On for OEM Screen

Dip 5: UP On for OEM Camera, O for after market camera

Dip 6: UP Not used.

Dip 7: UP Up 8” screen, Down for 4” screen

Dip 8: UP Up 8” screen, Down for 4” screen

13. Check to be sure the Map SD Card is installed in the Navigation unit.

Double check all connections, and then reconnect the vehicle battery.

Navigation Interface Operation:

CUE Equipped Vehicles:

To change the OEM radio to Navigation mode press

the Navigation icon on the main screen.

Exit Navigation by pressing the home key on the radio

face (see circled area). The nav will continue to operate

unless you have selected to stop the route or used the

Navigation Exit icon in the Nav application.

MyLink Equipped Vehicles:

If you have installed the switch, the NAV will be selected by

pressing each time to enter or exit the Nav application.

To enter the Nav application from the touch screen, press

the location on the screen noted by the star

for about 2 seconds. This location will work in any screen

or menu. Exit Navigation by pressing the same location again.

NOTE: When a call is received on Bluetooth the caller

information is displayed on the driver information center

above the steering column, use the SWC controls to answer calls.

For Navigation operation see the included quick start guide or download a full user’s manual from

WWW.ADVENTPRODUCTS.COM .

If the picture is not centered or does not ll the screen correctly you can adjust the picture size. Access the settings menu by

pressing the Menu button on the side of the Nav Interface Module.

Use the Menu button to scroll through the options and “+” or “-” buttons to adjust the value.

1. Contrast, Brightness and Saturation are all screen adjustments for picture quality.

2. Position H and V are for Horizontal and Vertical Position, use to adjust to t factory screen as needed.

3. IR-AV1, IR-AV2: NOT USED. Select NONE to insure proper operation.

4. Guide-L, Guide-R-CNTRL -These are controls for the position of the Parking Lines. By selecting + or - you can move the

position of the lines to match the vehicle width.

5. H-Size, V-Size: This will adjust the picture to meet the full screen size of the OEM panel.

Setup Menu

Contrast----------------------------50

Brightness-------------------------50

Saturation-------------------------62

Position-H-------------------------23

Position-V-------------------------3

IR-AV1------------------------------NOT USED

R-AV1-------------------------------NOT USED

Guide-L-----------------------------0

Guide-R----------------------------3

Guide-CNTRL---------------------OFF

H - SIZE-----------------------------16

V - SIZE-----------------------------40

Specications:

No. Name Parameters

1 Video input 0.7Vpp with 75 Ω impedance

2 Synchronized signal strength 3‐5Vpp with 5K impedance negative pulse synchronization.

3 RGB resolution By changing DIP4 user can select HD/VGA or normal

HD : 800X480 or VGA :640X480

Normal NTSC‐vertical 240 (or 234)

4 Av1, Av2, cam video 0.7Vpp with 75 Ω impedance

5 Av1, Av2, cam format NTSC/PAL/SECAM Automatic switch

6 Normal power 4.8W [0.4A @12V]

7 Stand by current < 10mA

8 Trigger level threshold (Reverse and

switching)

>5V trigger

9 Output current of additional control

port 1.2.7

Maximum current of 2A.

10 Operating temperature range ‐40 +85C

11 Dimensions 15.6 X 9.2 X 2.2 Cm

For Technical Support Please Call 1- 800-323-4815.

Vehicle Specic Instructions, Tech Tips, and Installation notes can be found at

WWW.AUDIOVOXUNIVERSITY.COM

128-9394

Voxx Electronics Corporation

Hauppauge, NY 11788

Technical Assistance: 1-800-323-4815

WWW.ADVENTPRODUCTS.COM .

Printed in China

Inhaltsverzeichnis

Andere Advent Auto-Navigationssystem Handbücher

Advent

Advent TOCLJ-OE100 Bedienungsanleitung

Advent

Advent GMCNAV2 Bedienungsanleitung

Advent

Advent CADNAV2 Bedienungsanleitung

Advent

Advent ESCNAV2 Bedienungsanleitung

Advent

Advent NM102 Bedienungsanleitung

Advent

Advent OTOTUN1 Bedienungsanleitung

Advent

Advent CHRYNAV1 Bedienungsanleitung

Advent

Advent AMN101 Bedienungsanleitung

Advent

Advent Navigation Bedienungsanleitung

Advent

Advent OVW1 Bedienungsanleitung

Advent

Advent CADNAV2 Bedienungsanleitung

Advent

Advent CHVNAV2 Bedienungsanleitung

Advent

Advent ADVUNI300 Bedienungsanleitung

Advent

Advent UV630I Bedienungsanleitung

Advent

Advent NAV102 Bedienungsanleitung

Advent

Advent GMNAV1 Bedienungsanleitung

Beliebte Auto-Navigationssystem Handbücher anderer Marken

Clarion

Clarion Navigation In-Car Entertainment Bedienungsanleitung

Rosen

Rosen DP-1001 Bedienungsanleitung

Alpine

Alpine INE-W970HD Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot DX-N Bedienungsanleitung

Pioneer

Pioneer MZ360500EX Bedienungsanleitung

Sanyo

Sanyo NVM-4030 - Easy Street - Automotive GPS... Bedienungsanleitung

AvMap

AvMap Geosat 2C Bedienungsanleitung

Eonon

Eonon GE01B Bedienungsanleitung

Pioneer

Pioneer AVIC-Z920DAB Bedienungsanleitung

Nextar

Nextar M3-MX - Automotive GPS Receiver Bedienungsanleitung

Furrion

Furrion NV2200 Bedienungsanleitung

Mio

Mio MOOV 200-Series Bedienungsanleitung

Prestigio

Prestigio GeoVision 5150 Bedienungsanleitung

Magellan

Magellan Maestro 4210 - Automotive GPS Receiver Konfigurationshandbuch

Garmin

Garmin StreetPilot c510 Bedienungsanleitung

Garmin

Garmin nüvi 2200 Bedienungsanleitung

Garmin

Garmin 2610/2650 Bedienungsanleitung

Mazda

Mazda 107006AN Bedienungsanleitung