AEC NS Series Bedienungsanleitung

NS Series

Uninterruptible Power Supply

User Manual

NS1500/2200/3000-1T

SAVE THIS MANUAL

This manual contains important instructions that should be followed during

installation, operation, and storage of this UPS. Please read these

instructions carefully before installation and start-up of the UPS.

Rev. 11/2005

Table of Contents

1. Introduction ________________________________________________________1

2. Safety Instructions __________________________________________________4

3. Installation _________________________________________________________6

3.1 Unpacking_______________________________________________________6

3.2 Installation ______________________________________________________6

4. Operation __________________________________________________________7

4.1 Control Panel ____________________________________________________7

4.2 Turn On the UPS__________________________________________________7

4.3 Turn Off the UPS__________________________________________________7

4.4 LED Indicators ___________________________________________________8

4.5 Control Panel Buttons_____________________________________________8

4.6 Audible Alarms__________________________________________________10

4.7 Communications Interface ________________________________________11

5. Storage ___________________________________________________________15

6. Troubleshooting____________________________________________________16

6.1 General Problems _______________________________________________16

7. Specifications______________________________________________________18

FCC Part 15 NOTICE: Pursuant to section 15 of the FCC rules, this product has been tested and thereby

complies with the conditions of a Class B digital device, which have been established for offering

sufficient protection against dangerous interference for installation in a residential area. Installation and

use of the equipment should comply with the instructions provided in order to avoid such interference

due to the amount of radio frequency energy that is radiated and generated by the equipment. In spite

of this, we cannot assure that a certain amount of interference may not occur in some installations. If, by

turning on and off, it can be deduced that your radio or television reception is found to be influenced by

harmful interference from the equipment, it is recommended to use one of the following preventive

measures: Place the receiving antenna in a separate location or orientation. Ensure a greater distance is

achieved between the receiver and the equipment. Ensure that your equipment is connected to an outlet

on a separate circuit than the receiver. Contact a technician experienced with radio and TV or a dealer

for further assistance.

User Manual NS1500/2200/3000-1T

1. Introduction

The NS series UPS are advanced true On-Line uninterruptible power supplies

which produce reliable and pure sine-wave power to equipment, ranging from

computers and telecommunication systems to industrial automated equipment.

The On-Line design enables the UPS to adjust and filter power fluctuations

continuously and automatically under normal power conditions. During a power

failure, it can provide immediate back-up power from the batteries without any

interruption. When an overload or UPS malfunction occurs, the system will

automatically transfer to bypass mode and continue supplying output equipment

with utility power. When the overload is removed, the UPS will automatically

transfer back to inverter mode. Malfunctions may be resolved by restarting the

UPS. All the transferences are achieved within 4 ms without interruption.

Nomenclature

Front & Rear Panel of NS2200

1 Rev. 11/2005

Control Panel

User Manual NS1500/2200/3000-1T

Front & Rear Panel of NS1500

Rear Panel of NS1500

2 Rev. 11/2005

Control Panel

User Manual NS1500/2200/3000-1T

3 Rev. 11/2005

Standard Outlets of NS1500

Standard Outlets of NS2200/NS3000

User Manual NS1500/2200/3000-1T

4 Rev. 11/2005

2. Safety Instructions

This manual contains important instructions that should be followed during

installation, operation, maintenance, and storage of this UPS.

IMPORTANT SAFETY WARNINGS AND INFORMATION

WARNING! DO NOT USE FOR LIFE-SUPPORT EQUIPMENT

•DO NOT use this UPS for applications in which a malfunction or failure of the UPS

would cause failure or alter the performance of a life-support equipment.

WARNING! RISK OF ELECTRICAL SHOCK

•The outlet receptacles may be electrically live even when the UPS is disconnected

from the AC power source.

•This UPS contains potentially hazardous voltages. Do not open the UPS. There

are no user-serviceable parts inside.

•For service personnel, the battery and input circuits are not isolated. High voltage

may exist between the battery terminal and ground; use an electric meter to check

the voltage before beginning any repairs.

•Apart from battery replacement, all maintenance and service work should be

performed by qualified service personnel.

•Turn off the UPS and unplug it from the AC power source before battery replacement.

•Do not connect your UPS to an outlet that is not properly grounded.

•Do not remove the ground connection from the UPS’ power plug.

UPS LOCATION PLACEMENT AND CONNECTION

•Install the UPS in a clean indoor environment, away from excess moisture or heat,

dust or direct sunlight, flammable gases or fumes.

•Place and operate the UPS where the surrounding temperature range is from 32°F to

104°F (0 - 40°C). Optimal battery life is obtained if the temperature does not exceed

86°F (30°C).

•Keep the UPS on a flat, stable surface with adequate space around it for proper

ventilation. Do not block the vents.

•The UPS must be powered from a single phase grounded wall outlet; not a surge

protector or power strip. Avoid storage locations that are excessively humid, near

water, near heat sources or in direct sunlight.

•Do not plug appliances such as electric heaters, toasters and vacuum cleaners into

the UPS.

User Manual NS1500/2200/3000-1T

5 Rev. 11/2005

•Do not connect inductive loads, such as laser printers, to the UPS.

BATTERY WARNING

•This UPS contains a sealed lead-acid battery. DO NOT open the battery.

•DO NOT short or bridge the battery terminals with any object.

•Once the battery has reached the end of its life, ensure that they are properly

disposed. REFER TO YOUR LOCAL LAWS AND REGULATIONS FOR BATTERY

DISPOSAL REQUIREMENTS.

User Manual NS1500/2200/3000-1T

6 Rev. 11/2005

3. Installation

3.1 Unpacking

Examine the packing carton for damage. Notify the carrier immediately if damage is

present. Retain the package for future use.

3.2 Installation

1. Before making any connection and switching on the UPS, please check the

following conditions: (1) your AC power source should be 120 volts and 60Hz and

(2) all the equipment connected to the UPS does not exceed the maximum output

power of the UPS (as indicated on the UPS rear panel and specifications shown

in Section 7).

2. Connect the power cord of the UPS to a working, grounded AC wall socket.

3. Charge the batteries for 8 hours before use. When the power cord is plugged

into the wall outlet and AC power is available, the UPS will automatically recharge

its batteries. You may use the UPS immediately without recharging, but the

backup time may be less than the rating.

4. Connect the power cord of your equipment to the output receptacles of the UPS.

Check the type of power cord before

connecting the plug to the outlet. The

power cord plug should mate with the

outlet.

User Manual NS1500/2200/3000-1T

7 Rev. 11/2005

4. Operation

4.1 Control Panel

4.2 Turn On the UPS

1. Turn on the utility power to the UPS.

2. Turn on the input switch from the rear panel.

3. The UPS begins its auto-start sequence. This takes about ten seconds.

4. When the LINE and INVERTER LEDs are lit, the UPS will be ready for use.

4.3 Turn Off the UPS

1. Press ON/OFF button. The INVERTER LED will turn off and the BYPASS LED

turns on.

2. Turn off the input switch from the rear panel. All LEDs will turn off.

User Manual NS1500/2200/3000-1T

8 Rev. 11/2005

4.4 LED Indicators

FAULT – UPS is abnormal.

CHARGER – Charger is working.

PFC OL – Input current too large due to low input utility power.

GREEN – UPS is in green mode.

LINE – Utility power is normal. Input relay is in closed state.

BOOST – Booster is working. (During start up and DC mode)

INVERTER – Inverter is working.

BYPASS – Load is supplied with utility power when the input relay is in closed state.

LOAD 25/50/75/100% – Output load at 25, 50, 75, 100%.

BATTERY 25/50/75/100% – indicates the status of the batteries.

100% – Battery is fully charged.

75% – Battery is in normal voltage state.

50% – Battery is going to enter low voltage state.

25% – Battery is going to enter cut-off state.

The battery voltage level for each LED indication is as follows:

NS1500 NS2200 NS3000

100% >52.8V >79.2V >105.6V

75% 49.6V~52.8V 74.4V~79.2V 99.2V~105.6V

50% 44.0~49.6V 66.0~74.4V 88.0~99.2V

25% 42.0~44.0V 63.0~66.0V 84.0~88.0V

4.5 Control Panel Buttons

ON/OFF –

1. When utility power is available, the UPS can be turned on or shut off by

pressing the ON/OFF button.

2. When the UPS is operating normally in the inverter mode, pressing the

ON/OFF button will be change the UPS to BYPASS mode. The UPS will

stop supplying power to the connected equipment if the utility power is

unstable.

FUNCTION (TEST) –

While the UPS is working under normal status, pressing the Function Button will

test the batteries for 10 seconds. The batteries, instead of the utility power,

will supply power to all circuits. If the UPS switches back to Normal Mode after

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung