77
NOTE: Be careful not to position the panel light in such a way that
prevents normal operation or damages the cord.
WARNING
Only hang or mount the panel light in an area where no electrical
wires, utility cables, pipes, or other obstructions are located.
&RQWDFW\RXUORFDOXWLOLW\FRPSDQ\RUDTXDOL¿HGHOHFWULFLDQLI\RX
are unsure. Do not hang panel light from any electrical power
cord. Ensure panel light is securely installed to prevent falling
object hazard. Failure to follow these instructions can result in
electrocution, electrical shock, or other serious personal injury.
Hanging the panel light using the keyholes:
ŶInstall two screws approximately 12mm apart.
ŶPlace the wide portion of the keyholes over the heads of screws.
ŶSlide the panel light down until the screws are inside the narrow
portion of the keyholes and the panel light is secure.
Hanging the panel light using the hooks:
Ŷ +DQJWKHSDQHOOLJKWIURPDVWXUG\ORFDWLRQOLNHDIHQFHXVLQJ
WKHEXLOWLQKRRNV
Mounting the panel light to a rod using the rod pocket:
ŶThe panel light can be mounted on rebar, a rod or tube using the
pocket on the base of the panel light.
NOTE: The mounting post must have a diameter less than
PP
OVER TEMPERATURE PROTECTION
If overheating occurs, the panel light will attempt to cool itself by
GLPPLQJ,IGLPPLQJGRHVQRWFRROWKHOLJKWVXI¿FLHQWO\LWZLOOVKXWRII
As soon as the unit reaches normal operating temperature, it can be
WXUQHGRQDJDLQ,IWKHSDQHOOLJKWVKXWVRIIDOORZDSSUR[LPDWHO\
PLQXWHVRIFRROGRZQWLPHEHIRUHDWWHPSWLQJWRUHVXPHRSHUDWLRQ
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
7HPSHUDWXUHVLQH[FHVVRI& ) UHGXFH WKH SHUIRUPDQFH
of the battery pack. Avoid extended exposure to heat or sunshine
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
)RUDQRSWLPXPOLIHWLPHWKHEDWWHU\SDFNVKDYHWREHIXOO\FKDUJHG
after used.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
6WRUH WKH EDWWHU\ SDFN ZKHUH WKH WHPSHUDWXUH LV EHORZ &
and away from moisture.
6WRUHWKHEDWWHU\SDFNVLQDFKDUJHGFRQGLWLRQ
Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
/LWKLXPLRQ EDWWHULHV DUH VXEMHFW WR WKH 'DQJHURXV *RRGV
Legislation requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
ŶThe user can transport the batteries by road without further
requirements.
Ŷ &RPPHUFLDOWUDQVSRUWRI/LWKLXP,RQEDWWHULHVE\WKLUGSDUWLHVLV
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately.
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
ŶEnsure that battery contact terminals are protected and
insulated to prevent short circuit.
ŶEnsure that battery pack is secured against movement within
packaging.
ŶDo not transport batteries that are cracked or leak.
Check with forwarding company for further advice
BATTERY PACK PROTECTION
The battery pack has overload protection that protects it from being
overloaded and helps to ensure long life. Under extreme stress the
battery electronics switch off the machine automatically. To restart,
switch the machine off and then on again. If the machine does not
start up again, the battery pack may have discharged completely. In
this case it must be recharged in the battery charger.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only AEG accessories and AEG spare parts. Should
components need to be replaced which have not been described,
please contact one of our AEG service agents (see our list of
JXDUDQWHHVHUYLFHDGGUHVVHV
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label and
order the drawing at your local service agents or directly at:
Techtronic Industries (Australia) Pty. Ltd.
32%R[
Mount Waverley VIC 3149
7HOQR
Australia
Techtronic Industries N.Z. Ltd.
32%R[
3HQURVH$8&./$1'
7HOQR
New Zealand
SYMBOLS
Safety alert
Regulatory Compliance Mark (RCM). Product
meets applicable regulatory requirements.
Please read the instructions carefully before
starting the machine.
Class II, double insulated
Do not dispose of electric tools together with
household waste material. Electric tools and
electronic equipment that have reached the end of
their life must be collected separately and returned
to an environmentally compatible recycling facility.
