aegex 10 Bedienungsanleitung
USER GUIDE
aegex10 USER GUIDE
www.aegex.com
USER GUIDE
2
REGULATORY STATEMENTS
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. How-
ever, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful inter-
ference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modications not expressly approved by the party responsi-
ble for compliance could void the user’s authority to operate this equipment.
This device complies with FCC and Industry Canada RF radiation exposure
limits set forth for general population (uncontrolled exposure). This device
must not be collocated or operating in conjunction with any other antenna
or transmitter.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, includ-
ing interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Hereby, Aegex Techologies LLC declares that all CE Marked Aegex products incorporating Radio and Telecoms Terminal Equipment functionally
are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
FCC & IC STATEMENTS
CE STATEMENT
USER GUIDE
FRONT
12
3
4
5
6
Ambient Light Sensor
Recognizes the ambient light and adjusts
the display brightness if enabled in the
operating system
Front Microphone Outlet
Front Camera
2MP camera for video conferencing
Camera Indicator LED
Lights up if camera is activated and
during device boot and shutdown
Windows Button
Touch it to return to the start menu
3
Charging Indicator LED
OFF not connected to charger
ORANGE charging
GREEN fully charged
RED charge error
USER GUIDE
TOP SIDE
4
Volume Keys
Push the left button (-) to reduce the volume,
use the right button (+) to increase the volume
On / Off Button
Push it once to start the tablet; push it again
to enable the sleep mode. Push and hold it to
shut down the device. You will be instructed on
screen to slide to shut down your device.
7
8
USER GUIDE
RIGHT AND BOTTOM SIDE
5
CTIA Audio Jack
Combined microphone &
speaker connector
Docking Connector 9
Securing Kensington Locks
Charging Pads 11
MicroSDXC Card Slot
13
MicroUSB Interface For charging only
14
USB 2.0 Port
15
16
10
Stereo Speakers (on the sides) 12
USER GUIDE
REAR VIEW
6
NFC Antenna Position
Can be used to read NFC & RFID tags
with appropriate software
17
Rear Microphone Outlet
Camera Flash LED 19
Rear Camera
8MP camera for high resolution images & video
20
Battery Lid
21
18
USER GUIDE
REPLACING BATTERY / ADDING SIM CARD
7
1. Remove the 4 hex screws from the
corners of the battery cover using the
provided hex tool.
TO REPLACE THE BATTERY:
2. Take off the battery cover by pulling on the
lid carefully – specically on the corner
with the slant.
USER GUIDE
REPLACING BATTERY / ADDING SIM CARD
8
3. Release locking by pulling on the battery
holder hook (A) towards the bottom of
the device then pull the battery up (B).
Repeat process for other battery
holder hook.
4. Enter the Micro SIM card into the slot in
the center of the right side. Make
sure you have the Micro SIM card in
the correct direction (chip facing down).
(B)
1.RELEASE LOCKING
(A)
2. LIFT UP1.RELEASE LOCKING2. LIFT UP
(B)
(A)
USER GUIDE
REPLACING BATTERY / ADDING SIM CARD
9
REPLACING BATTERY / ADDING SIM CARD
2. Replace battery cover by pushing down on the lid carefully by
following the steps illustrated in the image:
A) Align the battery door to the back housing. The corner with the
slant is positioned to align with the enlarged access point in the
lower left corner of the case.
B) Engage the battery cover snaps by:
i. Snapping in the middle top snaps rst
ii. Pressing down the battery cover edge by using two hands
a) Moving out symmetrically from the top center
to the top left and right corners
b) Then from top to bottom on both side edges
c) And then from the bottom corners in to the
bottom middle symmetrically
d) Finish at the bottom middle snaps
C) Verify that the battery cover is ush with the rear housing on
all edges and conrm that there is no bulge or gap. If you feel
resistance, check pin alignment. Do not force the cover down as
damage to connecting pins will occur.
When putting the battery back in place:
1. Make sure the battery securely clicks in
place on both sides.
End
3. Then replace the 4 corner hex screws
of the battery cover using the provided
hex tool. The recommended torque for
the screw is 10-12Ncm.
1.RELEASE LOCKING 2. LIFT UP1.RELEASE LOCKING2. LIFT UP
USER GUIDE
USING THE TABLET FOR THE FIRST TIME
10
Connect power supply for the rst time by opening
the right hand door and connecting the micro
USB and make sure battery is fully charged before
disconnecting. While the cable is connected to the
micro USB, it should be handled with care to avoid
connector damage
Press the power button
Follow the instructions in the operating system
to complete the setup
1
2
3
Andere Handbücher für 10
1
Inhaltsverzeichnis
Andere aegex Tablette Handbücher
