Aeotec 2E Bedienungsanleitung

17-08-13

Micro Smart Dimmer 2E manual - Aeotec

aeotec.com/z-wave-in-wall-switches/877-micro-sei-2e-manual-instructions.html

1/10

Micro Smart

Dimmer 2E

manual

IMPORTANT

The electricity to the circuit must be shut off during installation

for safety and to ensure that wires are not short circuited

during installation which will cause damage to the Micro

Module.

The following instructions have been designed to assist in the

installation of the Aeotec by Aeon Labs Z-Wave in wall Smart

Dimmer. Please note that the instructions are for the 2nd

Edition of the Micro Smart Dimmer.

In-Wall Electrical

Installation Instructions:

17-08-13

Micro Smart Dimmer 2E manual - Aeotec

aeotec.com/z-wave-in-wall-switches/877-micro-sei-2e-manual-instructions.html

2/10

Remove the two screws securing the cover plate.

Remove the wall switch cover plate.

Remove the two screws securing the wall switch to the wall

box. Disconnect both wires from the wall switch.

Dismounting In Wall Box.

17-08-13

Micro Smart Dimmer 2E manual - Aeotec

aeotec.com/z-wave-in-wall-switches/877-micro-sei-2e-manual-instructions.html

3/10

Live – Hot wire (Black wire) Connect to Live terminal of Micro

Smart Energy Illuminator G2.

Neutral (White wire) Note! If this wire is not present in the

box, a neutral wire must be pulled into the box.

Load wire – Connect to Load terminal of Micro Smart Energy

Illuminator G2.

Preparing and Connecting

Wires

The Aeotec Micro Smart Energy Illuminator G2 must first be

diagram is as follows:

Note

The “3V Out” terminal should be used only with the Aeon

Micro Touch.

17-08-13

Micro Smart Dimmer 2E manual - Aeotec

aeotec.com/z-wave-in-wall-switches/877-micro-sei-2e-manual-instructions.html

4/10

Signal connection – Using two 18 AWG copper wires,

connect the terminals of the wall switch to Micro Smart

Energy Illuminator G2 as shown.

Make sure that the ends of the wires from the wall

box are straight (cut if neccessary).

Remove insulation from each wire and the wall box

as shown.

Side wire connection

Position all wires to provide room for the device. Place Micro

Smart Energy Illuminator G2 inside the wall box towards the

back of the box.

Position the antenna towards the back of the box, away from

all other wiring.

Reinstall the wall switch to the wall box.

Mounting In Wall Box.

17-08-13

Micro Smart Dimmer 2E manual - Aeotec

aeotec.com/z-wave-in-wall-switches/877-micro-sei-2e-manual-instructions.html

5/10

Reinstall the cover plate onto the wall box.

Restore Power

Restore power at the circuit breaker or fuse. Installation is

complete.

Z-Wave Network

Instructions:

The Aeotec Micro Smart Energy Illuminator G2 must be

paired (included) into a Z-Wave network before it can receive

Z-Wave commands to turn on/off/dim and report its energy

usage. The Micro Smart Energy Illuminator G2 can only

communicate to devices within it’s own Z-Wave network.

Note

The LED on the Micro Smart Energy Illuminator G2 will blink

17-08-13

Micro Smart Dimmer 2E manual - Aeotec

aeotec.com/z-wave-in-wall-switches/877-micro-sei-2e-manual-instructions.html

6/10

Press the button labeled “Include” on the Aeotec Minimote to

begin the Z-Wave inclusion process.

Note

To include the Aeotec Micro Smart Energy Illuminator G2

with other controllers, please consult the operation manual for

these controllers on how to include Z-Wave products into an

existing network.

While the Micro Smart Energy Illuminator G2 is powered in a

3-wire system, the external switch/button can be toggled to

initiate pairing into the Z-Wave network. Or the internal button

can be pushed to initiate pairing into the Z-Wave network, if

Micro Smart Energy Illuminator G2 was not put into in-wall

box.

if it is currently not paired into a Z-Wave network.

Adding/Including/Pairing the

Micro Smart Energy Illuminator

G2 into a Z-Wave Network

17-08-13

Micro Smart Dimmer 2E manual - Aeotec

aeotec.com/z-wave-in-wall-switches/877-micro-sei-2e-manual-instructions.html

7/10

Troubleshooting

If the Aeotec Micro Smart Energy Illuminator G2 was not

successfully included into any Z-Wave network, the LED will

be blinking slowly continually. If the Aeotec Micro Smart

Energy Illuminator G2 was successfully included to a Z-Wave

network, the Status Indication LED will either be solid on or

off (depending on if the switch is on or off).

Press the button labeled “Remove” on the Aeotec Minimote

to begin the Z-Wave removal process.

Note

Removing/Resetting the Micro

Smart Energy Illuminator G2

from your Z-Wave Network

17-08-13

Micro Smart Dimmer 2E manual - Aeotec

aeotec.com/z-wave-in-wall-switches/877-micro-sei-2e-manual-instructions.html

8/10

To remove the Aeotec Micro Smart Energy Illuminator G2

from other controllers, please consult the operation manual

for these controllers on how to remove Z-Wave products from

an existing network.

While the Micro Smart Energy Illuminator G2 is powered in a

3-wire system, the external switch/button can be toggled 10

times in quick succession to initiate removing from the Z-

Wave network. or the internal button can be pushed to initiate

pairing into the Z-Wave network, if Micro Smart Energy

Illuminator G2 was not put into in-wall box.

Troubleshooting

If the Aeotec Micro Smart Energy Illuminator G2 was

removed from the Z-Wave network, the Status Indication LED

will be blinking. If the Aeotec Micro Smart Energy Illuminator

G2 was not successfully removed from the Z-Wave network,

the Status Indication LED will either be solid on or off

(depending on if the switch is on or off).

Note

Another way to reset Aeotec Micro Smart Energy Illuminator

G2 is pressing and holding the button which is on Micro

Smart Energy Illuminator G2 20 seconds, if Micro Smart

Energy Illuminator G2 was not put into in-wall box.

Turning On/Off/Dim the Micro

17-08-13

Micro Smart Dimmer 2E manual - Aeotec

aeotec.com/z-wave-in-wall-switches/877-micro-sei-2e-manual-instructions.html

9/10

Smart Energy Illuminator G2

Use any of the below methods to allow power through or cut

power from the Micro Smart Energy Illuminator G2.

Through the usage of Z-Wave commands built into Z-

Wave certified controllers and gateways. (The specific Z-

Wave commands supporting this function are the Basic

Command Class

Pressing the button on the Micro Smart Energy Illuminator

G 2 will toggle power flow (on/off) through the Micro

Smart Energy Illuminator G2. By holding the button, the

lamp will be dimmed up or down.

Change Mode on the External

Switch/Button Control

The Aeotec Micro Smart Energy Illuminator G2 is set to

be controlled via 2-state(flip/flop) external wall switch by

default. Pushing and holding the button 6 seconds on the

Micro Smart Energy Illuminator G2 will swap between this

default mode and the momentary push button external

wall switch mode.

Through the usage of Z-Wave command built into Z-Wave

certified controllers and gateways. (The specific Z-Wave

command supporting this funtion is Configuration

Command Class) Please consult the operation manual

for these controllers for specific instructions on changing

external wall switch mode of the Aeotec Micro Smart

Energy Illuminator G2.

Monitoring Energy

Consumption

The Aeotec Micro Smart Energy Illuminator G2 can report

wattage energy usage or kWh energy usage to a Z-Wave

gateway or controller when requested. If this function is

supported by the gateway/controller, the energy consumption

will be displayed in the user interface of the

gateway/controller. (The specific Z-Wave commands

supporting energy monitoring are the Meter Command

17-08-13

Micro Smart Dimmer 2E manual - Aeotec

aeotec.com/z-wave-in-wall-switches/877-micro-sei-2e-manual-instructions.html

10/10

Class. Automatic reports are sent to association group 1,

which is setup via the Association Command Class.) Please

consult the operation manual for these gateways/controllers

for specific instructions on monitoring the Micro Smart

Energy lluminator G2.

Note

The Micro Illuminator G2 (without the words “Smart Energy”)

does not have the ability to monitor energy consumption.

Inhaltsverzeichnis

Andere Aeotec Dimmer Handbücher

Aeotec

Aeotec Smart Dimmer 6 Bedienungsanleitung

Beliebte Dimmer Handbücher anderer Marken

ZooZ

ZooZ ZEN54 LR Bedienungsanleitung

Lex

Lex 6KW Bedienungsanleitung

DIODE LED

DIODE LED TOUCHDIAL Mini Bedienungsanleitung

Viessmann

Viessmann 5590 Bedienungsanleitung

Teleco

Teleco TVSTICK868RGB29 Bedienungsanleitung

INSTEON

INSTEON LampLinc 2457D2 Bedienungsanleitung

LEGRAND

LEGRAND WattStopper RH703PTU Bedienungsanleitung

ADB

ADB EURODIM TWIN TECH Bedienungsanleitung

Sinope

Sinope DM2550ZB-C4 Bedienungsanleitung

SkyLink

SkyLink SK7 Bedienungsanleitung

Makel

Makel RC Bedienungsanleitung

Lightronics

Lightronics XC-62 Bedienungsanleitung

Triton Blue

Triton Blue DM-1225 Bedienungsanleitung

ETC

ETC ES750 Betriebsanleitung

NA OMEGA + Bedienungsanleitung

GE ZB3001 Bedienungsanleitung

LSC

LSC DP-1210 Bedienungsanleitung

Leviton

Leviton DDS8800 Betriebsanleitung