AERMEC MODUCONTROL Bedienungsanleitung
SUMMARIZED USER MANUAL
WATER
CHILLER
MODUCONTROL
CHILLERS
REVERSIBLE HEAT PUMPS
CONDENSING UNITS
• EXTERNAL UNITS
• HIGH EFFICIENCY
• HOT WATER PRODUCTION
UP TO 50ºC
READINGMENU•USERMENU•ERRORMENU
EN
READINGS MENU
Reading menu
The reading menu gives the user the option to read all parameters
Lista indici e relative letture MENÚ LETTURE (nessuna password)
Index - String Meaning of the reading
Water output temperature
Water input temperature
Coil temperature
Force gas temperature
Outside air temperature
Delivery pressure
Suction pressure
Thermostat
CP times
Hours of operation (thousands)
Hours of operation (units)
Compressor pickup current
(thousands)
Index - String Meaning of the reading
Compressor pickup current (units)
Software release
Minor software releases
Setting currently in use
DCP pressure setting
Operating hours
COMPRESSOR 2 (thousands)
Operating hours
COMPRESSOR 2 (units)
Compressor pickup current
COMPRESSOR 2 (thousands)
Compressor pickup current
COMPRESSOR 2 (units)
Power fraction
Required frequency (INVERTER)
Pressure drop
Parameters only visible in heat pump models
Parameters only visible in models set for hot domestic
water production
Parameters only visible in the models with DCP installed
Parametes only visible in bicompressor models
Parameters only visible in the models with inverter
compressor
USER MENU
User menu
The user menu gives the user the option to change settings
1. press the srewdriver symbol
2. 000 apears
3. Press the srewdriver again
4. Use up and down keys to nd a setting
5. Press the screwdriver again (blinking of index nr)
6. Change the setting with up and down keys
7. Conrm with screwdriver
For Opticlimate set:
1 STF on 26°C
2 BNF on 1°C
-
- -
SF1: index (6) user menu;
SF2: index (8) user menu;
TF1: index (7) user menu;
TF2: index (9) user menu;
In cooling mode, the work setting is calculated au-
tomatically on the basis of the outside temperature,
following the logic highlighted in the diagram.
SC1: index (A) user menu;
SC2: index (C) user menu;
TC1: index (B) user menu;
TC2: index (d) user menu;
In heating mode, the work setting is calculated au-
tomatically on the basis of the outside temperature,
following the logic highlighted in the diagram.
USER MENU
-
-
USER MENU
-
-
rature (depending on the type of control set by parameter (0) in the installer menu) is less than the hot
Lista indici e relative letture MENÚ LETTURE (nessuna password)
Index - String Meaning of the reading
Water output temperature
Water input temperature
Coil temperature
Force gas temperature
Outside air temperature
Delivery pressure
Suction pressure
Thermostat
CP times
Hours of operation (thousands)
Hours of operation (units)
Compressor pickup current
(thousands)
Index - String Meaning of the reading
Compressor pickup current (units)
Software release
Minor software releases
Setting currently in use
DCP pressure setting
Operating hours
COMPRESSOR 2 (thousands)
Operating hours
COMPRESSOR 2 (units)
Compressor pickup current
COMPRESSOR 2 (thousands)
Compressor pickup current
COMPRESSOR 2 (units)
Power fraction
Required frequency (INVERTER)
Pressure drop
Parameters only visible in heat pump models
Parameters only visible in models set for hot domestic
water production
Parameters only visible in the models with DCP installed
Parametes only visible in bicompressor models
Parameters only visible in the models with inverter
compressor
USER MENU
ERROR MENU
Error
An error can be reset by switching the main power of the unit off for 5 seconds.
When there is air trapped inside the system E104 will appear. Bleed the system and switch the power off to reset.
After rst time operation E104 will appear several times until all air is out.
We advise to use automatic bleeders at the highest point of the water-system.
-
-
-
-
-
Notes
-
-
-
-
-
-
-
-
-
122
ERROR MENU
--
-
--
-
ERROR MENU
Andere Handbücher für MODUCONTROL
2
Inhaltsverzeichnis
Andere AERMEC Steuereinheit Handbücher
AERMEC
AERMEC MODUCONTROL Stücklistenhandbuch
AERMEC
AERMEC WMT 10 Technische Daten
AERMEC
AERMEC VHL22 Bedienungsanleitung
AERMEC
AERMEC VCZ41 Bedienungsanleitung
AERMEC
AERMEC VCFD 1 Bedienungsanleitung
AERMEC
AERMEC RTE240 Bedienungsanleitung
AERMEC
AERMEC MCR Bedienungsanleitung
AERMEC
AERMEC VMF-E5 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
